Page 1
NQUIRE SERIES Micro Kiosk User Guide Version: V1.0...
Page 2
The products depicted in this manual may include software copyrighted by Reg. nr. 17109876 Newland Europe BV or a third party. The user, corporation or individual shall not duplicate, in whole or in part, distribute, modify, decompile, disassemble, decode, reverse engineer, rent, transfer, or sublicense such software without prior written consent from the copyright holders.
Page 3
Revision History Version Description Date V1.0 Initial release. Feb 29th, 2024...
Hardware Instruction & Operations (Installation & Uninstallation) 1. LED Indicator Power Red LED is solid on Power supply is on. Status Red LED is Off Power supply is off. Ethernet Green LED flashes constantly Network connected Connection Green LED is solid on Network disconnected 2.
4. Expansion Slots & Add-on modules ODULES MSR M NFC M ODULE ODULE INSTALLATION (Enable the NFC/MSR in the system setting first) Below is an example of NFC installation Unscrew and remove the covering part. Gently lift the cover up with your hand.
Page 8
Plug the jack of the antenna into the socket, then install the cover. Remove the cover of the NFC antenna and secure it with a screw to ensure the fixation of NFC and NQuire Install the cover of the NFC antenna Notes: The installation steps for MSR are similar to NFC.
7. DC-In Jack Plug the power adapter into the power jack, and fix the position with a bracket to prevent it from loosening. DC-In Jack bracket 8. Barcode Scanner The scan engine is set up in auto mode as the default setting. LED will light up when any object shows in front of the barcode scanner within proper distance, and the barcode engine will automatically scan when a barcode showed within a proper distance.
9. Control I/O Ports & Cover There are control IO ports (RS-232 & GPIO) under the Control IO cover (#22 in Quick Start). From left to right From left to right Typical Application Circuit for General Purpose Output (GPO):...
Page 13
Electrical Characteristics: GPIO1_3V3, GPIO2_3V3, and GPIO3_3V3 voltage requirements are equal to 3.3V. OUT VCC (external connection required) should be externally connected and requires an external series circuit. The series circuit size is set based on current requirements. The voltage requirement for OUT VCC is not greater than 24V. It is required that the current into the device from OUT-A and OUT_B inputs be less than 80mA at 60 degrees Celsius (subject to temperature variations, refer to above diagram).
and not greater than 20V. (External series circuit can increase input power supply voltage, with the requirement that the input current does not exceed 50mA.) 10. Interface The interfaces are shown as below :...
Chapter 2 Accessory & Installation VESA Wall Mount Installation & Operation 1. Select a mounting location that is convenient for operation. 2. Remove the screw attaching the bracket to the chassis of The VESA 75 mount. 3. For wall mounting, install the four plastic wall anchors in a wall and then secure the bracket of VESA 75 mount to the wall using the four large screws.
Chapter 3 Feature Programming Home Screen Open an app: Tap it. View all apps/Open apps list: Swipe up from the bottom of the screen to view all the apps. Swipe up Apps list...
Connected Device -> “Connected devices”, and set USB, Bluetooth, and NFC parameters according Tap the app icon to your needs. Apps -> “Apps”, then view app usage and handle special app access. Tap the app icon...
Notification -> “Notification”, then manage device notifications, including notification history, Tap the app icon notification on lock screen, do not disturb mode, and other parameter settings.
Display -> “Display”, and set the brightness level, dark theme, night light, and other Tap the app icon parameters on the screen shown below as per your needs.
About Phone -> “About phone”, then view information such as the device name, product model, Tap the app icon MEID, Android version, build number, and software updates.
Infrared Sensing , and tap “Infrared sensing” to manually set the Tap the app icon on the Home screen then infrared sensing distance (7cm to 30cm from near to far).
Ethernet Tap the app icon on the Home screen then to set ethernet parameters. Currently, the default setting is a static IP. Note: If you intend to connect the device to the internet via Ethernet, ensure Wi-Fi is turned off and insert the Ethernet cable into the device's Ethernet port.
Chpter 4 Important Safety and Handling Information Please read the instructions carefully before equipment installation and using the device. Do not install the product at a height exceeding 2 meters. Do not put the product in a high-temperature, humid, or dusty environment. ...
Page 32
SCANNING MADE SIMPLE Newland EMEA Rolweg 25 +31 (0) 345 87 00 33 4104 AV Culemborg info@newland-id.com The Netherlands @NewlandEMEA...