Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for Ripack MULTICOVER 960
- Page 1 ® MULTICOVER USER's GUIDE www.ripack.com...
-
Page 3: Table Of Contents
- 1 - ® MULTICOVER EALER UIDE Guarantee ............2 Warnings ............3 Technical Data ............4 Assembly ............5 Instructions for Use ..........6 Maintenance and Repair ........9 ® MULTICOVER is a product of RIPACK – 33185 France... -
Page 4: Guarantee
In case of dispute, jurisdiction lies solely with the Courts of Bordeaux, FRANCE. OR ANY CLAIM UNDER THE GUARANTEE PLEASE ENCLOSE THE COPY OF THE INVOICE FROM YOUR SUPPLIER OUR GUARANTEE BEGINS AT THE DATE OF INVOICE FROM YOUR SUPPLIER ® MULTICOVER is a product of RIPACK – 33185 France... -
Page 5: Warnings
SHRINK FILM A SEALING BY HEAT PROCESS ® MULTICOVER MUST BE USED ONLY INSIDE OF LOCATIONS DEVOID OF MOISTURE ORDER GUARANTEE DURABILITY YOUR EQUIPMENT ALWAYS DISCONNECT THE POWER AFTER WORK ® MULTICOVER is a product of RIPACK – 33185 France... -
Page 6: Technical Data
Power supply - Tension and welding Power 230 V (50/60 Hz) - 24 V . 0,5 KVA 4 rubber casters Ø 100 mm Mobility 2 fix casters + 2 swivel casters with lock ® MULTICOVER is a product of RIPACK – 33185 France... -
Page 7: Assembly
There is only to put it onto the appropriate support (photo 1) and connect it to the M (photo 2) then to the mains supply (photo 3). ULTICOVER The M is now ready for operation. ULTICOVER Photo 1 Photo 2 Photo 3 ® MULTICOVER is a product of RIPACK – 33185 France... -
Page 8: Instructions For Use
Lower the upper jaw with one of the two handles at the end of the bar • down to the triggering of the timer. A tone indicates the sealing phase. • ® MULTICOVER is a product of RIPACK – 33185 France... - Page 9 During high speed work, the sealing wire keeps residual heat; the sealing time can then be reduced consequently. Photo 6 Photo 7 ® MULTICOVER is a product of RIPACK – 33185 France...
- Page 10 Cut the film by actuating the guided knife and release the sleeve by • pulling it slightly. The anti-return rollers tight hold the film in position for the next bags. • Photo 8 ® MULTICOVER is a product of RIPACK – 33185 France...
-
Page 11: Maintenance And Repair
Replace the worn wire by a new one. Tighten the wire with the screw • at one end and by tightening it with pliers at the opposite end. Tighten the 2 other screws. • Silicone Teflon (x2) Screw (x4) Sealing wire ® MULTICOVER is a product of RIPACK – 33185 France... - Page 12 Retighten the whole onto the M • ULTICOVER Photo 9 Photo 10 Comments Burns marks on Teflon are normal after a certain period of use. An early wear is due to a wrong sealing time. ® MULTICOVER is a product of RIPACK – 33185 France...
- Page 13 - 11 - NOTES ® MULTICOVER is a product of RIPACK – 33185 France...
- Page 14 DECLARATION DE CONFORMITE CE 7 Rue de Betnoms 33185 LE HAILLAN FRANCE Déclare que le produit : MULTICOVER 960 correspond aux dispositions et aux normes harmonisées suivantes : complies with the following regulations and harmonized standards : Directive basse tension 2006/95/CE...
Need help?
Do you have a question about the MULTICOVER 960 and is the answer not in the manual?
Questions and answers