Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Steibel Eltron FET
Summary of Contents for Steibel Eltron FET
- Page 1 OPERATION AND INSTALLATION Remote control » FET...
-
Page 2: Table Of Contents
CONTENTS | OpEraTiON General information OpEraTiON OPERATION General information �����������������������������������������2 relevant documents 2 Safety instructions 2 General information Other symbols in this documentation 2 Units of measurement 3 The chapter "Operation" is intended for appliance users and qual- Safety ����������������������������������������������������������3 ified contractors. -
Page 3: Other Symbols In This Documentation
Material losses Appliance description (appliance damage, consequential losses and environmen- tal pollution) The FET digital remote control enables convenient operation of one appliance disposal heating zone. The remote control measures the relative humidity and room temperature. The software is divided into program menus and the SETTiNGS f This symbol indicates that you have to do something. -
Page 4: Start Screen
OpEraTiON Operation Start screen Touch-Wheel 16.06. 16.06. 22° 14° 1 Date 2 Weather 3 Outside temperature 4 Menu level 5 Time 6 room temperature / relative humidity 4.3.1 Program menus 7 active operating mode Swipe your finger clockwise or counter-clockwise around the 8 Day Touch-Wheel in the various program menus to set a different value for the relevant menu. -
Page 5: Menu
Note 5.1.2 ECO if summer mode is active on the heat pump manager, settings made at the FET remote control will not have in this menu, you can set heating operation and, under certain any effect. circumstances, also DHW to setback mode for a specific interval. - Page 6 OpEraTiON Menu f Swipe your finger around the Touch-Wheel to adjust the comfort temperature. f Take your finger off the Touch-Wheel. The display shows the selected setting for a few seconds before switching automati- cally to the relevant menu. The entry is saved. Note The value set in the heat pump manager for the comfort temperature has been changed for the assigned heating...
-
Page 7: Settings
OpEraTiON Menu Application … „ HEATING CIRCUIT For higher DHW demand (e.g. guests). This menu item tells you which heating circuit your device is set up for. SETTINGS Note in this menu, you can read the information and make certain The heating circuit was defined in the commissioning settings. -
Page 8: Heating
iNSTaLLaTiON Troubleshooting BRIGHTNESS OFF INTERVAL … …„ … …„ Select BriGHTNESS OFF to adjust the brightness of the display. if Select iNTErVaL to adjust the interval during which the change you do not make any entries on the device for a certain interval, in room temperature from the start screen applies (see chapter the brightness of the display is reduced to the value selected here. -
Page 9: Preparations
CAN-High CAN-High ranged either vertically or horizontally opposite one another. WpM heat pump manager FET remote control 9.2.2 Installation without a flush box f To secure the wall mounting enclosure, drill four holes Ø 3/16˝ (Ø 5 mm). f When routing the CaN bus cable, be careful not to damage it when drilling the fixing holes. -
Page 10: Commissioning
iNSTaLLaTiON Commissioning 1 Device 2 Wall mounting enclosure 3 6-pole CaN bus female connector f Connect the CaN bus cable to the female connector. f Connect the female connector to the back of the device. 11. Commissioning 11.1 Initial start-up Once the device has been wired to the heat pump manager, the commissioning wizard starts up. - Page 11 Guarantee The guarantee conditions of our German companies do not apply to appliances acquired outside of Germany. In countries where our subsidiaries sell our products a guarantee can only be issued by those subsidiaries. Such guarantee is only grant- ed if the subsidiary has issued its own terms of guarantee. No other guarantee will be granted.
- Page 12 Deutschland Verkauf Tel. 05531 702-110 | Fax 05531 702-95108 | info-center@stiebel-eltron.de STIEBEL ELTRON GmbH & Co. KG Kundendienst Tel. 05531 702-111 | Fax 05531 702-95890 | kundendienst@stiebel-eltron.de Dr.-Stiebel-Straße 33 | 37603 Holzminden Ersatzteilverkauf www.stiebel-eltron.de/ersatzteile | ersatzteile@stiebel-eltron.de Tel. 05531 702-0 | Fax 05531 702-480 info@stiebel-eltron.de www.stiebel-eltron.de Australia...
Need help?
Do you have a question about the FET and is the answer not in the manual?
Questions and answers