ION EB-L2-W Operating Manual
  1. Manuals
  2. Brands
  3. ION Manuals
  4. Controller
  5. EB-L2-W
  6. Operating manual
ION EB-L2-W Operating Manual

ION EB-L2-W Operating Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
CONTROLLER
OPERATING MANUAL
PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION AND USE
Controller EB-L2-W
RJ9 (4P4C) plug
(connect to controller)
P.1
www.ionlight.com | info@ionlight.com | Exclusively Distributed by GGen Distribution Corp.
L I G H T I N G R E I M A G I N E D
ION EB-L2-W | 0-10V COMPATIBLE
PRODUCT COMPONENTS
5V DC
2x Temperature sensor
power adapter (2A)
with cable (5m/16ft)
RJ14 (6P4C) plug
(connect to ballasts)
CONTROLS
2x Controller cable
(5m/16ft)
Push the four wires into the middle openings
of a RJ14 plug. The orientation of the plug
does not matter as long as the wires are entered
in the central four openings.
KEY
A
Quick-key
View and adjust output level
B
Down
Navigate down in menu/decrease value
C
Enter
Go to menu/confirm
D
Up
Navigate up in menu/increase value
E
Back
Navigate back in menu/cancel/reset
F
M
0-10V main menu and PLC main menu conversion
Ionlight.com | Exclusively Distributed by GGen Distribution Corp.
Bracket

Advertisement

Table of Contents
loading

Related Manuals for ION EB-L2-W

Summary of Contents for ION EB-L2-W

  • Page 1 L I G H T I N G R E I M A G I N E D CONTROLLER OPERATING MANUAL ION EB-L2-W | 0-10V COMPATIBLE PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION AND USE PRODUCT COMPONENTS 2x Controller cable 5V DC...
  • Page 2 CONTROLLER L I G H T I N G R E I M A G I N E D CONNECTIONS A. 5V DC input B. Cage clamp connector ECM1 (output is active when main channel is on) C. Cage clamp connector ECM2 (output is active when main channel is off) D.

  • Page 3: Controlling Auxiliary Equipment In "Follow Mode" (One Room)

    CONTROLLER L I G H T I N G R E I M A G I N E D CONTROLLING AUXILIARY EQUIPMENT IN “FOLLOW MODE” (ONE ROOM) CONTROLLING AUXILIARY EQUIPMENT IN “FOLLOW MODE” (ONE ROOM) www.ionlight.com | info@ionlight.com | Exclusively Distributed by GGen Distribution Corp. www.ionlight.com | info@ionlight.com | Exclusively Distributed by GGen Distribution Corp.

  • Page 4: Connecting A Temperature Shutdown, Sensor Failure Or Power-Off Alarm To The Controller

    CONTROLLER L I G H T I N G R E I M A G I N E D CONNECTING A TEMPERATURE SHUTDOWN, SENSOR FAILURE OR POWER-OFF ALARM TO THE CONTROLLER The controller has two pairs of cage clamps marked “A-NC” (normally closed) and “A-NO” (normally open).

  • Page 5: Calibrating The Temperature Sensor(S)

    CONTROLLER L I G H T I N G R E I M A G I N E D 3. SWITCH PERCENT MODE BETWEEN 115% AND 100% • Press “enter”, the controller menu will open. Press the arrow keys ▲▼ to locate “100%” or “115%” and press “enter.” The “100%” or “115%” screen will open. •...

  • Page 6: Programming A Light Cycle

    CONTROLLER L I G H T I N G R E I M A G I N E D 2. PROGRAMMING A LIGHT CYCLE • Press “enter”, the controller menu will open. Press the arrow keys ▲▼ to locate “Light Cycle” and press “enter”. The “Light Cycle” screen will open. (23) In this screen the •...

  • Page 7: Setting Safety Shutdown Temperature

    CONTROLLER L I G H T I N G R E I M A G I N E D • Press “enter”, the controller menu will open. Press the arrow keys ▲▼ to locate “Auto-Dim Temp” and • press “enter”. •...
  • Page 8 CONTROLLER L I G H T I N G R E I M A G I N E D 6. ACTIVATE OR DEACTIVATE THE LIGHTS MANUALLY OR SET AUTOMATIC MODE • Press “enter”, the controller menu will open. Press the arrow keys ▲▼ to locate “Output mode” and press “enter”. •...

  • Page 9: Sensor Disconnected

    CONTROLLER L I G H T I N G R E I M A G I N E D INTERPRETING DISPLAY MESSAGES 1. SENSOR DISCONNECTED SENSOR FAILURE <- 0℃ OFF 22.5℃ -> 22.5℃ OFF • The message “Sensor failure” appears when the T1 temperature sensors are not plugged in. •...

Table of Contents