Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for SI Solo 3
Summary of Contents for SI Solo 3
- Page 1 Solo 3 - 375 Flown Kit Bracket Installation Instructions...
- Page 2 Thank you for purchasing an SI product. If you have any questions or need any assistance with your Solo 3 - 375 Flown Kit, we would love to help you. Technical Support: 512.832.6939 Hours of Support: 7:30am - 5pm CST screeninnovations.com...
- Page 3 CONTENTS Initial Consideration ......... Pg 1 Parts in the Box ..........Pg 2 Installation ............Pg 3 - 11 Warranty ............Pg 12...
-
Page 4: Initial Consideration
2''- 8'' from the end of the cassette. Standard kits come with 2 Solo 3 - 375 Flown Kit Bracket assemblies. Each bracket can hold 50 lbs safely. For screens over 100 lbs, a third bracket is required. -
Page 5: Parts In The Box
PARTS IN THE BOX (2) Solo 3 Flown (2) Solo 3 Flown Kit Kit 375 - Brackets 375 - Top Plates 3/32'' & 5/64'' hex keys (4) No.10 Screws for plate heads Steel Cable 1/16'' x 96'' Parts in the Box... -
Page 6: Installation
1. Determine the desired viewing area with vertical centerline of the projected viewing area. 2. The Solo 3 Flown Kit Brackets must be installed 2"- 8" from each end of the cassette. Measure the overall length of the cassette to determine the min. and max. - Page 7 Cassette Length 2'' to 8'' Decora Flying bracket secured to Viewing ceiling joist or Height structural supports. Viewing Width Center Line of Viewing Area Installation...
- Page 8 3. Run the provided cable through the top plates and install the top plates to structural supports. Each bracket & cable is capable of supporting up to 50 lbs. No.10 Screws for plate heads Installation...
- Page 9 4. Position the brackets on the cassette so that they will be in line with the hanging cables. 5. Loosen the set screw in the brackets so that the cassette hook is positioned all the way down. Installation...
- Page 10 6. Hook the cassette onto the bracket. Then use the 5/64'' hex key to turn the bottom screw untill the cassette bottoms out on the bracket. Installation...
- Page 11 7. Use the 3/32'' hex key to tighten the locking screw in the back of the bracket. Installation...
- Page 12 8. Insert the cables in receptacle on top of the pin and raise the cassette to the desired height. Pull the cable through the grip-lock while lifting to raise the cassette. Press the cap on the top of the grip-lock while pushing down on the bracket to lower the cassette.
- Page 13 9. Ensure the cassette is horizontally level by adjusting the verticle position of the brackets on the cables.. Installation...
- Page 14 10. Ensure the cassette is plumb by sliding it forward or backward on the bracket slots. Adjusting one side will affect the other side so fine tuning will be required between both the ends. Once the cassette is plumb on both ends then tighten the knurled nut onto the top of the bracket to lock the grip-lock into place.
-
Page 15: Warranty
WARRANTY New SI products carry a standard 1- year warranty on parts and labor. FCC INFORMATION This device complies with Part 15 of the FCC Results. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. - Page 16 Screen Innovations 9715-B Burnet Rd, Suite 400 Austin, TX 78758 512.832.6939 www.screeninnovations.com v.1.2 February 2024...
Need help?
Do you have a question about the Solo 3 and is the answer not in the manual?
Questions and answers