boytone BT-48UM - Microphone System Manual

Parts checklist

Before installing your wireless microphone, Here are a few things you should do/know:
Receiver
Handheld microphone
DC power adapter
1/4" male to male cable
AA battery
User manual

*Be sure to keep original packaging in case of re-shipping is needed.

Matters Need Attention

1. Check to see whatever the local voltage accord with operating receiver voltage (Wrong selection may lead to burn out of receiver)
2. Do not dismantle the machine on your own. For internal repairing, please contact the local distributor or accepted service center.
3. When the machine will not be used for a long time, please disconnect the power plug from the receiver.
4. Do not recharge your batteries unless the batteries are rechargeable.

Cleaning

Please make sure the power is disconnected before cleaning or repairing the machine. The machine can be cleaned by using a soft cloth with water. Dry the machine with a dry cloth and let it air dry for 15 minutes.
Please do not use volatile gasoline, diluents or other chemicals to clean the machine or the surface will be damaged.

Receiver Front Panel

1. Power switch: turn on or turn off
2. Display panel: show all kinds or information (such group, signal, frequency and RF, AF etc)
3. Volume control
4. IR window
5. Menu button: From Left to right, IR sync, left button, SET button, right button

Receiver Rear Panel

6. Antenna
7. Balance audio output
8. Mix out
9. DC input jack: 12-15V

Transmitters

10. LCD screen
11. Power switch
12. IR window
13. Antenna
14. Power Switch: Press the button for 2-3 seconds to turn on, the LED lights. Press again for 2-3 seconds to turn off.
15. Audio Input Interface.
16. LED Indicator: Light when turn on. Flashes when low power.
17. LCD Display: Display frequency in formation.
18. Adjustment Button Set: Set button is in the middle. Touch it to enter and adjust the volume menu. Touch the left and right buttons to adjust.
19. Infrared Data Receive Window: receive data transmitted signal.
20. Battery Store.
21. Battery Cover.

Function Descriptions

1. Select the frequency: Press SET button, when FRE flashing, press right or left button to adjust it
2. Choose the Channel: in the Select the frequency menu, press SET button, CH flashing, meanwhile press right or left button to choose the channel.
3. IR sync: Press IR button to send the IR data

Installation

1. Contact with 12-15V 1000mA DC adaptor.
2. Connect one end of a 1/4" TO 1/4" CABLE to the receiver's UNBALANCE AUDIO OUTPUT (MIX) and the other end to a karaoke mixer, karaoke player or karaoke power amplifier 1/4" microphone input. If you are using the BALANCE AUDIO OUTPUT, use a XLR to XLR cable or XLR to 1/4" cable.
3. Unscrew the microphones handle cover(counter-clockwise) to check to see if there are batteries. If not, put the batteries into the microphones with the negative and positive end of the battery correspond the negative and positive end of the microphone. Screw the microphone handle back on.

Connected

1. The power supply is connected to the power input jack of the receiver. The input voltage of the power adapter must be consistent with the local power specifications.
2. XLR balanced output and 6.3mm unbalanced output jack on the rear panel of the receiver, based on the need to be connected.

Troubleshooting

If you are having operating problems, or suspect something wrong with the unit, please check the troubleshooting list below to see if the issue is a result of incorrect operation rather than equipment malfunction.

Features

• Microphone and receiver channels auto-sync via infrared
• Two high densitive microphones with LCD indicators
• Noise reduction technology
• Uni-Directional rechargeable battery design
• Applicable for medium&small stages, karaoke halls and home entertainment etc.

Specifications

Receiver

• Carrier Wave Frequency Range: UHF 470-608MHz 470-608MHz
• Carrier Wave Stability: 10PPM
• Sensitivity: -105dB @ sinad=12dB
• S/N Ratio: >105dB
• T.H.D.: <0.5% @ 1KHz
• Image Rejection: 85 dB typical
• Spurious Rejection: 75 dB typical
• Frequency Responses: 40Hz~18KHz
• Working Distance: >200 feet
• AF Output Impedance: 2.2KΩ
• Max. Output Level: Balance: 0-400mv, Unbalance: 0-200mv
• Display: LCD
• Power Supply: External DC Power Supply, 1A, 12~15V DC
• Output Connector: XLR Balanced Socket, Unbalance TRs 6.35mm Socket

Transmitter

• Transmitter Power: 30mW
• Spurious Emission: <40dB(with carrier)
• Display: LCD
• Battery Voltage: 1.5V x 2
• Battery Life: 6-8 hours

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download boytone BT-48UM - Microphone System Manual