1. Manuals
  2. Brands
  3. wallPen Manuals
  4. Printer
  5. E2
  6. User manual

wallPen E2 User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
USER MANUAL E2
E2
USER MANUAL E2
User Manual
USER MANUAL wallPen E2
USER MANUAL E2

Advertisement

Table of Contents
loading

Summary of Contents for wallPen E2

  • Page 1 USER MANUAL E2 USER MANUAL E2 User Manual USER MANUAL wallPen E2 USER MANUAL E2...
  • Page 3 E2 User Manual wallPen GmbH Version 2.0.4 | © 2016-2021 wallPen GmbH...

  • Page 5: Table Of Contents

    General Print Advisories ..................69 6.2.2 Results not Satisfactory ..................70 6.2.3 Working with the Reference Point ................. 71 6.2.4 Wall-to-Wall Printing ..................... 74 6.2.5 Print as High as Possible ..................83 Color Management Version 2.0.4 | © 2016-2021 wallPen GmbH...
  • Page 6 Wifi Network Connection ..................117 10. Miscellaneous 10.1 Suitable Substrates ....................122 10.2 wallPen Glass Magic ....................124 10.3 Recommended Software ................... 126 10.4 Technical Data & Dimensions ..................128 11. Change Log 12. Notes Index wallPen E2 | User Manual...

  • Page 7: Preface

    Preface...
  • Page 8 All texts, photos and graphic designs used in this manual are protected by copyright. If you wish to use parts of this manual, please contact wallPen GmbH as the author. No part of this publication may be reproduced in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of the publisher.

  • Page 9: Scope Of Delivery

    Scope of Delivery...
  • Page 10 Scope of Delivery Scope of Delivery wallPen E2 printer /w 70 cm vertical extension axis  One 7 Inch Android Tablet  Four Ink Bottles à 200 ml (One of each color CMYK)  One Bottle with 0,5l Print Head Flushing-Liquid ...

  • Page 11: Safety Information

    Safety Information...

  • Page 12: Mechanical Hazards

    Safety Information Safety Information Mechanical Hazards When operating the wallPen, there is a risk of unprotected parts moving in a controlled manner. During operation, the wallPen printer must always be protected against unauthorized access and well monitored. The emergency stop switch must be freely accessible at all times! The wallPen must always be secured and monitored during operation.

  • Page 13: Uv Ink Hazards

    The wallPen printer is only suitable for UV ink from the manufacturer. Printheads are very sensitive devices. Do not use any other ink than original wallPen ink. The use of other ink does not guarantee a proper functionality of the printer and will void any warranties.
  • Page 14 · Always wear protective gloves and goggles when handling UV ink. · It is important to consult a doctor as soon as possible, even if the symptoms subside after a few minutes wallPen E2 | User Manual...

  • Page 15: Uv Ink Expiration

    Always wear special UV safety glasses when operating the printer. Such UV safety goggles are supplied with every printer. If in doubt, consult a doctor as soon as possible. Talk to your wallPen partner about which protective goggles from specialist retailers are recommended.

  • Page 16: Disposal Of Consumables

    Liquid UV ink is hazardous material. Please do not dispose of UV ink in household waste, as these residues can contaminate the environment. UV ink must be disposed of as hazardous waste. Please inform yourself about the regulations and disposal options at your local disposal company. wallPen E2 | User Manual...

  • Page 17: Hardware

    Hardware...

  • Page 18: Components

    Hardware Hardware Components The wallPen E2 consists of the following components: 1. Platform Unit (A) Base frame with two drive wheels in the rear and two steered wheels in the front. 2. Cabinet Unit (B) Aluminium frame system with control cabinet. The unit is placed on the platform and fastened with two screws.

  • Page 19: Assembly

    Assembly 4.2.1 Basic Assembly Before you start setting up, make sure that there is enough room for the wallPen to do the printing you plan to do. · Are there any obstacles? · Is the ceiling height above the entire print area sufficient? ·...
  • Page 20 Hold the slide - as shown in the figure - approx. 3 cm above the platform against the control cabinet profile. Here, the slide profile is guided by two locating pins. Now carefully lower the slide onto the platform. wallPen E2 | User Manual...
  • Page 21 Here, the axis is guided by two locating pins. Carefully lower the base axis onto the slide profile und gently tighten screw "A" and then the two screws "B". Version 2.0.4 | © 2016-2021 wallPen GmbH...
  • Page 22 Hold one of the two extension axis approx. 3 cm above the base axis as shown in the figure ..and gently lower it onto the base axis. Gently tighten the screw as shown on the left. wallPen E2 | User Manual...
  • Page 23 Assembly Put the strut into position and tighten the two screws gently. Version 2.0.4 | © 2016-2021 wallPen GmbH...
  • Page 24 Hardware Hold the second extension axis approx. 3 cm above the first extension axis as shown in the figure ... wallPen E2 | User Manual...
  • Page 25 ... and gently lower it onto the base axis. Gently tighten the screw as shown on the left. Check that the EMERGENCY STOP switch (A) is unlocked and the main switch (B) is switched off. Version 2.0.4 | © 2016-2021 wallPen GmbH...
  • Page 26 · Remove the magnetic metal cover in front of the printheads. · Open the left front flap and loosen all four/five white plastic pipe clamps and holding it in place (A) and pressing the lock in the direction of the arrow wallPen E2 | User Manual...

  • Page 27: Print-Head Assembly Front

    Print-head Assembly Front Attach the cross profile extension to the cross profile. Slightly tighten the two screws integrated in the extension at the top and bottom to attach it to the cross profile Version 2.0.4 | © 2016-2021 wallPen GmbH...

  • Page 28: Print-Head Assembly Half-Front

    Prepare to release the break by holding the slide with your left hand (red marker) to avoid it to drop down, once the break is released Push the "Brake Release Button" with your right hand ... wallPen E2 | User Manual...
  • Page 29 25 cm as shown on the left. Turn the power switch to OFF. Place the print-head at the front end of the axis across profile, hold it in place and lead it sideways onto the two guiding pins. Version 2.0.4 | © 2016-2021 wallPen GmbH...

  • Page 30: Print-Head Assembly Rear

    4.2.4 Print-head Assembly Rear Attach the cross profile extension to the cross profile. Slightly tighten the two screws integrated in the extension at the top and bottom to attach it to the cross profile wallPen E2 | User Manual...
  • Page 31 Slightly tighten the screw to fix the printhead unit in place Route the cable from the slide unit to the printhead as shown in the figure, plug it into the back of the printhead and lock it. Version 2.0.4 | © 2016-2021 wallPen GmbH...

  • Page 32: Print-Head Assembly Half-Rear

    Push the "Break Release"-button with your right hand ..and keep it pushed while pulling the slide unit up for about 25 cm as shown on the left. Turn the power switch to OFF. wallPen E2 | User Manual...
  • Page 33 Gently tighten the screw as shown in the image. Route the supply cable from the slide to the printhead as shown in the figure, then plug its connector into the rear printhead socket and lock it with the black handle. Version 2.0.4 | © 2016-2021 wallPen GmbH...

  • Page 34: Disassembly

    Disassembly 4.3.1 Printhead Disassembly Select "Shutdown" from the main menu of the wallPen Control software (see Chapter "Software / wallPen Control / Settings") Wait about 10 seconds and switch off the device at the main switch. No matter in which of the four possible...
  • Page 35 · Loosen the two screws as shown in the figure on the left. · Carefully pull the extension sideways from the locating pins and stow it in its transportation bag. Version 2.0.4 | © 2016-2021 wallPen GmbH...
  • Page 36 "Park Profile" (C). Allow the slide to slide down at least far enough to safely reach the screw hole on the side for disassembly, so that the screw can be loosened there later. wallPen E2 | User Manual...

  • Page 37: Basic Disassembly

    Disconnect the power cable (B) from the power outlet and from the rear left jack of the platform. To remove the power cord, pull up the small locking lever (1), turn the plug housing 45 degrees counterclockwise (2), Version 2.0.4 | © 2016-2021 wallPen GmbH...
  • Page 38 (3). Loosen the two screws of the strut, carefully lift it upwards and store it in its transport bag. Loosen the screw of the upper extension. wallPen E2 | User Manual...
  • Page 39 Loosen the screw "A" and the two screws "B". Carefully lift the base axis by approx. 3 centimeters (A), move it away from the control cabinet (B) and stow it in its transportation bag. Version 2.0.4 | © 2016-2021 wallPen GmbH...
  • Page 40 Hardware Loosen the two screws (A and B). Carefully lift the slide by approx. 3 centimeters ..move it away from the control cabinet and stow the slide in its transport bag. wallPen E2 | User Manual...
  • Page 41 Lift the control cabinet carefully and parallel upwards without tilting it and store it in its transportation bag. Lift up the platform and finally store it also in its transportation bag. Version 2.0.4 | © 2016-2021 wallPen GmbH...

  • Page 42: Transport

    Take good Care! :-) Treat & maintain your wallPen well! The machine is a sensitive technical device and can quickly take damage if it is handled rough or treated with too little care. · Clean all components thoroughly after use! ·...
  • Page 43 Do not use these tissues to clean the printhead nozzles! You should try to find a similar product in your country or purchase these wipes directly from wallPen or from your wallPen partner. Version 2.0.4 | © 2016-2021 wallPen GmbH...

  • Page 45: Software

    Software...

  • Page 46: Wallpen Processor

    (photo) templates represent. In this respect, "ripping" is always just a compromise for such technical reasons. In order to rip a graphic file with the wallPen Processor, certain requirements have to be met for the image file. In general we recommend a current version of the software "Adobe...
  • Page 47 CMYK, RGB or RGB(A) · Compression: · Color Depth: 8 bit · Layers: None · Resolution: 300 DPI The Splash Screen At software start, a splash screen is displayed. During the display the system is initialized. Version 2.0.4 | © 2016-2021 wallPen GmbH...
  • Page 48 Software After the first start After the initial start-up of the software, a preset for at least one printer must be created. To do this, select "Add a new preset"and enter a suitable name. wallPen E2 | User Manual...
  • Page 49 "A-Z" , letters "a-z", numbers "0 to 9", underscore "_" and dash /minus "-". Once the new preset is shown in the list, select "Edit" The following dialog will appear: Version 2.0.4 | © 2016-2021 wallPen GmbH...
  • Page 50 D - Horizontal Calibration - This setting is obsolete and can be ignored for the wallPen E2 model. You can find a better procedure to calibrate the printer in the chapter "Software | wallPen Control". This section explains how to calibrate the machine by respecting the exact wheel diameter, so that both horizontal calibration settings can be left at 1000.
  • Page 51 You can find a better procedure to calibrate the printer in the chapter "Software | wallPen Control". This section explains how to calibrate the machine by respecting the exact wheel diameter, so that both horizontal calibration settings can be left at 1000.
  • Page 52 Bulgarian, Dutch, English, French, German, Greek, Italian, Norwegian, Polish, Portuguese, Russian, Slovak, Spanish, Swedish and Turkish. If your language is not yet available and you would like to help, please contact us directly or via your wallPen E2 | User Manual...
  • Page 53 Processor wallPen partner. It's easy to add new languages and will help a lot to improve the software accordingly. b - Import Path - Which directory should be opened by default to select PNG or TIF files for import? c - Export Path - Which directory should be used by default for saving in order to create ".wallpen"...
  • Page 54 This function is identical with the possibility to drag and drop an image into the upper left area of the main screen of the wallPen Processor. Use the mouse to drag and drop the desired PNG or TIF file according to the above specifications to determine an image for calculation.
  • Page 55 Some sketches, comics and drawings appear somewhat more intense and strong without "ICC Processing", however with possibly deviating colors. If the switch is activated, the image is compared with the defined ICC input and output profiles below. Version 2.0.4 | © 2016-2021 wallPen GmbH...
  • Page 56 "Knowledge Base / Download"-Section on https://service.wallpen.com but you are also very welcome to share own profiles you may have measured in and created on different substrates and environments for the public use of other wallPen users. G - Print Settings a - Multi Pass Printing - Select whether the design is to be printed in one, two, four or eight pass mode.
  • Page 57 In the printer options (see section "Software - wallPen Control", a compensation value can almost eliminate this offset, so that most motifs are printed bidirectionally.

  • Page 58: Wallpen Control

    Once the correct configuration has been selected, select "CONTINUE" at the bottom right. to proceed to the positioning dialog. (see Chapter "Software / wallPen Control / Positioning" below) wallPen E2 | User Manual...

  • Page 59: Positioning

    G - Push (+) to move the printer stepwise away from the substrate. Each touch of the button moves the printhead by 0.5 mm. H - This switch activates the laser sensor's automatic wall distance system to maintain the current distance to the substrate in real time. Version 2.0.4 | © 2016-2021 wallPen GmbH...
  • Page 60 N - Enables precise approach to a freely definable vertical position. Enter the desired position in millimeters and press O - Continues to the image selection and the printing dialog (see Chapter "Software / wallPen Control / Printing" below) wallPen E2 | User Manual...

  • Page 61: Printing

    7 to 8 mm for a flat and vertical substrate to be printed. H - Preview of the current motif. The width of the image is displayed at the top and the height at the left. Version 2.0.4 | © 2016-2021 wallPen GmbH...
  • Page 62 STOP button and the main switch. Pressing the button briefly once pauses a print or resumes a paused print. If the button is held for more than two seconds, the pressure is canceled when it is released. wallPen E2 | User Manual...
  • Page 63 Control This abort is not reversible. Version 2.0.4 | © 2016-2021 wallPen GmbH...

  • Page 64: Settings

    B - Printer Settings a - Set the ink temperature in Celsius for each individual color. The default temperature for wallPen ink is 47°C. b - Changes the intensity of the UV lamps in real time, even during the printing process.
  • Page 65 Also, if your language is not yet implemented, please write us and we will check the possibilities of adding it. Thank you! Version 2.0.4 | © 2016-2021 wallPen GmbH...
  • Page 66 Software D - wallPen Control - This function allows you to jet ink for a set amount of time (3 seconds) to verify that the printheads are functioning properly. Be sure to cover each printhead with a soft, dust-free cloth before initiating the flushing process.

  • Page 67: Operation

    Operation...

  • Page 68: Tablet Operation

    3. Make sure that the EMERGENCY OFF switch is unsealed. 4. Connect the wallPen with the supplied power cord to a power outlet with ground fault circuit interrupter (RCD). 5. Switch on the device at the main switch.

  • Page 69: Best Practice

    With printers of the newest generation we have achieved very acceptable results in 4- pass printing with 600 DPI horizontally and 720 DPI vertically. This setting is in many cases an acceptable relation between quality and speed. Version 2.0.4 | © 2016-2021 wallPen GmbH...

  • Page 70: Results Not Satisfactory

    Is the ink expired? Was it stored too cold or too hot? · If all of the above suggestions do not lead to success, please contact your wallPen partner or wallPen directly. You may open a ticket or reach us by email at support@wallpen.com.

  • Page 71: Working With The Reference Point

    For this, the use of a is very helpful, which can be triangle ruler aligned at the bottom edge of the grid and both distances can be read quite exactly. Version 2.0.4 | © 2016-2021 wallPen GmbH...
  • Page 72 This example shows a result with a horizontal distance of 5.4 cm and a vertical distance of 8.0 cm. 7. Make a note of the values that you have determined for your reference. You may also enter them in this table: Date Machine Horizontal Distance Vertical Distance wallPen E2 | User Manual...
  • Page 73 4. Mark the exact position to the right below the desired image start point with a small pencil point (in our example 8 cm). 5. Move the printer and place the printer' laser dot exactly on the corresponding mark. 6. Print your image as usual. Version 2.0.4 | © 2016-2021 wallPen GmbH...

  • Page 74: Wall-To-Wall Printing

    - partly overlapping (fade-in/fade-out) - over the left image and finally to finish it to the right end. Wall-to-wall printing therefore requires some preparatory work in the graphics software. In this example we use Adobe PhotoShop with the image above. wallPen E2 | User Manual...
  • Page 75 3. Duplicate the layer with the image and name one layer "left" and the other "right". 4. Define "White" (C=0, M=0, Y=0, K=0) as the foreground color. 5. In Photoshop select the "Gradient tool" and then the gradient type "Foreground to Transparent". Version 2.0.4 | © 2016-2021 wallPen GmbH...
  • Page 76 Operation 6. Switch the layer "right" to invisible and activate the layer "left". 7. Click and hold the mouse cursor somewhere on the right help line (the blue dot in the picture below). wallPen E2 | User Manual...
  • Page 77 9. The result be look something like this... 10. Next switch the layer "left" to invisible and activate the layer "right"..Version 2.0.4 | © 2016-2021 wallPen GmbH...
  • Page 78 14. The result be look something like this... wallPen E2 | User Manual...
  • Page 79 16. Save the result as "right.png". Now the right image to be printed is saved and ready. 17. Select "Edit / Undo Crop" in Photoshop to get back to the previous state. 18. Switch the layer "right" to invisible and activate the layer "left" again. Version 2.0.4 | © 2016-2021 wallPen GmbH...
  • Page 80 20. Zoom to the area where the left help line meets the bottom of the screen. 21. Mark this spot in Photoshop by eraser or brush by marking, removing or coloring a small area. wallPen E2 | User Manual...
  • Page 81 - after printing the left image - it is used to precisely determine the starting point of the right image. 22. Save the result as "left.png". 23. Now process both images in the wallPen Processor. Version 2.0.4 | © 2016-2021 wallPen GmbH...
  • Page 82 31. Now push the printer back so far that the laser dot is in the area of the reference point mark. 32. Now position the wallPen as exactly as possible with the laser dot in the pencil mark. Make sure that the device is again very precisely parallel to the wall.

  • Page 83: Print As High As Possible

    7. Move the Y-axis up by the value previously determined. 8. Deactivate the simulation and restart printing. The slide will now move to the extreme physical end of the vertical axis and print the image as high as possible on the wall. Version 2.0.4 | © 2016-2021 wallPen GmbH...

  • Page 85: Color Management

    Color Management...
  • Page 86 You should not underestimate and at least basically understand. So you will learn over time how to draw the right conclusions in certain cases and then deliver perfect printing results on as many different surfaces as possible. wallPen E2 | User Manual...

  • Page 87: Color Models

    Color Models Like most offset, laser and inkjet printers, finally the wallPen requires CMYK colors to work on. But why? Let's take a closer look at the differences between the two most common colour models "RGB" and "CMYK" to better understand the fundamental reason for most printers using CMYK and most monitors using RGB...
  • Page 88 But what about printers? Printers are usually expected to print on a white (or at least a light) background, so an additive color model like RGB would not work out and meaningful results are not possible. wallPen E2 | User Manual...
  • Page 89 For this reason the letter "K" in CMYK does not stand for "blacK", but for "Key", since "Black" is regarded as a "supportive color". Version 2.0.4 | © 2016-2021 wallPen GmbH...

  • Page 90: Color Spaces

    Color Management Color Spaces wallPen E2 | User Manual...
  • Page 91 Such a range is called a "color space". It is helpful to understand the fundamental relationships in order to better understand the limitations of different color spaces and the reasons for their limitations. Version 2.0.4 | © 2016-2021 wallPen GmbH...
  • Page 92 However, in practice many color tones that are displayed are only be close to the target and the image becomes a compromise! wallPen E2 | User Manual...
  • Page 93 CMYK, certain color deviations will occur. To avoid any unpleasant surprises, you should always use a well calibrated monitor with activated "Proof Colors" under the "View" menu within PhotoShop set as "Working CMYK" (also see Chapter "Color Management | Color Correction"). Version 2.0.4 | © 2016-2021 wallPen GmbH...

  • Page 94: Icc Profiles

    If colors are missing in the list, the correction for these "intermediate colors" wallPen E2 | User Manual...
  • Page 95 A collection of universally applicable ICC profiles can also be found on our service website at https://service.wallpen.com. Version 2.0.4 | © 2016-2021 wallPen GmbH...

  • Page 96: Dot Gain

    A seemingly logical correction at first glance by reducing the intensity in the wallPen Processor fades the image not only in the midtones, but overall. It is better to either leave the correction to a suitable ICC profile or to do it "manually" in a software like Photoshop.
  • Page 97 Dot Gain The "Curve"-function in PhotoShop CC... The "Curve"-function in Affinity Photo... Version 2.0.4 | © 2016-2021 wallPen GmbH...
  • Page 99 Ink System...

  • Page 100: Ink System Ink System And Air

    Ink System Ink System and Air The wallPen Ink System has been specially designed to ensure the most reliable ink supply in the tightest of spaces while making the ink refill as easy as possible. Anyway, ink supply has generally one main enemy: AIR ! If there are air bubbles in the pipe system, the failure of one or more nozzles is very likely.
  • Page 101 Printhead Unit Treatment before each new print job If the wallPen is not used for some time, if air pressure changes considerably or if the print head unit is shaken during transport, even small amounts of air may pass through the nozzles into the ink system.

  • Page 102: Ink Refill

    Therefore, it is very important to keep air away from the printheads. The wallPen E2 uses aluminum bags as tanks, which can be refilled cleanly and quickly from bottles at the back of the printhead housing.
  • Page 103 Version 2.0.4 | © 2016-2021 wallPen GmbH...

  • Page 105: Service

    Service...

  • Page 106: Hardware Maintenance

    The system must be greased after a running distance of 2000 km or after 12 months - whatever comes first - to avoid abrasion and friction and to ensure smooth running. Only use the grease supplied by wallPen and the grease gun supplied.
  • Page 107 Allen key. 7. Repeat this procedure about every 100 km of running performance, or if you have the impression that the slide may run dry and rough. Better too often than too rarely! Version 2.0.4 | © 2016-2021 wallPen GmbH...

  • Page 108: Care Of The Toothed Belt

    The optimum tension is reached when the frequency is about 208 Hz. If the belt is significantly too tight, the motor bearing can be damaged over time. If the belt tension is too low, the entire platform may have some play and the print results may be negatively affected. wallPen E2 | User Manual...
  • Page 109 U-profile is still sufficiently lubricated. If the guide runs dry, spread some commercially available machine grease around the axis guide. Reattach the top cover. Version 2.0.4 | © 2016-2021 wallPen GmbH...

  • Page 110: Vertical Axis Brake Release

    9.1.5 Vertical Axis Brake Release The wallPen E2 is equipped with a high-quality motor brake on the vertical drive. In the de-energized state, the brake is closed, so it blocks the motor. This prevents the entire slide unit, including the print head, from falling down in the event of a power failure, possibly causing lasting damage or even injury.

  • Page 111: Calibration

    Calibration Calibration The wallPen E2 uses four (optionally expected to be available from Q4/2021 five) single printheads to print colors CMYK (W). Since these printheads are mounted separately and they must be calibrated to each other in order to achieve optimum printing results.
  • Page 112 Make sure "ICC color transformation" is disabled, process the image, copy the according ".wallpen" file onto a flash drive and load it on your wallPen printer. Prepare to print the processed file onto a smooth, white surface, best to use a blank paper sheet.
  • Page 113 +/- 30 pixels at 300 DPI for Magenta (D), Yellow (E) and Key (F). The lateral offsets are entered in the wallPen Processor Preset as they are read from the calibration image. Cyan should always be set to 0 as a reference and the values in the scale for magenta, yellow and key should be entered accordingly.
  • Page 114 For example, if magenta upwards (G) is in alignment with cyan at minus 3, then subtract the determined 3 from the cyan reference value of 10 and enter "7" in the settings for magenta printing upwards. wallPen E2 | User Manual...

  • Page 115: Printhead Replacement

    Insert the two supplied M4 screws into the now visible threaded holes by turning them 3-4 times. Lift the printhead at the front by approx. 5cm and place an object underneath. This prevents ink from leaking out of the ink bag when the tubing is loosened. Version 2.0.4 | © 2016-2021 wallPen GmbH...
  • Page 116 With a little practice, a good and secure connection is thus possible. Remove the object previously used to lift the printhead, lift the entire printhead and tilt it by approx. 45 degrees for a few seconds so that the printheads point towards wallPen E2 | User Manual...

  • Page 117: Wifi Network Connection

    "wallPen E2 XXXX", where "XXXX" are the last four characters of the wallPen mainboard serial number. If you need to reconnect to the wallPen WiFi network, please notice that the IP address to connect to the router is 192.168.0.1:9000 and the default Wifi connection password is "printingonwalls".
  • Page 118 Service Please do not change anything here without explicit instruction. A malfunction can be the result! wallPen E2 | User Manual...
  • Page 119 Wifi Network Connection Version 2.0.4 | © 2016-2021 wallPen GmbH...

  • Page 121: Miscellaneous

    Miscellaneous...

  • Page 122: 10.1 Suitable Substrates

    A big advantage of UV printing is the wide range of substrates that can be printed without problems. The wallPen UV ink is also particularly suitable for indoor printing, which, according to the manufacturer, contains hardly any chemical plasticizers and is therefore unlikely to evaporate.
  • Page 123 Version 2.0.4 | © 2016-2021 wallPen GmbH...

  • Page 124: 10.2 Wallpen Glass Magic

    Miscellaneous 10.2 wallPen Glass Magic When to use Glass Magic? wallPen Glass Magic is used on smooth, non-absorbent surfaces such as glass or some ceramic tiles. What does Glass Magic? wallPen Glass Magic destroys the oxygen layer on surfaces. This creates the optimal basis for UV inks to bond firmly and permanently to the substrate.
  • Page 125 A simple and effective way to remove the UV ink applied to a smooth surface with wallPen Glass Magic is to use a ceramic field scraper or conventional razor blade. When using solvents, there is a risk that the dissolved UV ink will smear, making it even more difficult to remove the ink without leaving a residue.

  • Page 126: 10.3 Recommended Software

    10.3 Recommended Software We have made good experience with some software products that often help us in our daily work with the wallPen. Here we present some of these tools to you... Benvista PhotoZoom Pro Some thoughts about "resolution" & "DPI"...
  • Page 127 With this viewer software even very large image files can be viewed. https://www.irfanview.com The license is subject to a fee for non-commercial use. If you are interested in purchasing, please contact the author directly. Version 2.0.4 | © 2016-2021 wallPen GmbH...

  • Page 128: 10.4 Technical Data & Dimensions

    80 x 60 x 170 / 400 cm (W x D x H) Total Weight: approx. 84 kg (incl. consumable supplies) Warranty: 12 months Shipping: Dispatch by air freight on one euro pallet Shipping Dimensions: 120 x 80 x 60 cm Shipping Weight: approx. 120 kg wallPen E2 | User Manual...

  • Page 129: Change Log

    Change Log...
  • Page 130 Date Remarks 2.0.0 September 11th 2021 · Initial release 2.0.1 September 15th 2021 · Supplements 2.0.2 September 22nd 2021 · Chapter "Printing" added · Chapter "Printhead Replacement" added 2.0.4 September 23nd 2021 · Small fixes wallPen E2 | User Manual...

  • Page 131: Notes

    Notes...
  • Page 132 Notes Notes wallPen E2 | User Manual...
  • Page 133 Version 2.0.4 | © 2016-2021 wallPen GmbH...
  • Page 134 Notes wallPen E2 | User Manual...
  • Page 135 Version 2.0.4 | © 2016-2021 wallPen GmbH...
  • Page 136 Notes wallPen E2 | User Manual...
  • Page 137 Version 2.0.4 | © 2016-2021 wallPen GmbH...

  • Page 139: Index

    Color Space 46, 94 Backlash Colormodel Backlit Monitor Colorspace Bag System Components Bags Compression Banding Computer Base axis 18, 19, 34, 37 Connectors Belt Continue BenVista Continue Printing Best Practice Correcting the Steering Version 2.0.4 | © 2016-2021 wallPen GmbH...
  • Page 140 Environmental Impact Homogeneous Print Evaporation Horizontal Calibration Exit Horizontal Channel Shifting 46, 111 Expected Colors Horizontal Distance Expiration Horizontal Resolution Export Path - I - - F - Fade Falsification of Colors ICC Processing 46, 111 wallPen E2 | User Manual...
  • Page 141 Luer Lock connector PhotoZoom Physical End - M - Pipe System Platform 18, 19, 34, 37 Manual Correction Position an Image Material Safety Data Sheet Power Failure Measurements Power requirement Mechanical Hazards Preface Version 2.0.4 | © 2016-2021 wallPen GmbH...
  • Page 142 Reset X-Pos Tablet Operation Residual Air Teeth Resolution 46, 126 Tension Retrieve Air T-Handle Key 18, 19, 34, 37 87, 90, 94 Third-party Licenses RGB Colors Tif-Files RGB Monitor Tilting Tissues Risks Tools 19, 34, 37 wallPen E2 | User Manual...
  • Page 143 Voltage - W - Wall Distance Wall End face WallPen Control WallPen User Interface WallPen® Glass Magic WallPen® Processor Wall-to-Wall Printing Warranty Washed-Out Effekt Weather Weight Wet Cleaning Tissues wetransfer.com Wheels Wind Windows Version 2.0.4 | © 2016-2021 wallPen GmbH...

Table of Contents