Advertisement
Quick Links
INSTALLATION INSTRUCTIONS
Please read these instructions throughout before installing as incorrect fitting will invalidate the guarantee.
We recommend that a technically competent installer/s undertake the installation.
If you are unsure about these instructions please contact Kudos Shower Products 01539 564040
The showertray must be checked thoroughly for defects. In the unlikely event that the product has a defect, it
must not be installed and you should contact your supplier.
Checks should include, but not limited to, the following:
Remove all packaging and the protective clear film on the showertray and ensure the colour and finish of the
showertray is acceptable.
Ensure the product is not cracked or chipped.
Ensure all visible surfaces are free from scratches.
Ensure that there is no twisting or distortions of the showertray.
Ensure that the showertray suitably drains water when levelled - refer to details below.
Ensure that the tray top surface is compatible with the intended shower enclosure, taking into account the loss of
dimensions from wall tiles - this is particularly important if you intend to recess the edges of the tray into the
walls.
INSTALLATION OF THE SHOWERTRAY WILL BE TREATED AS ACCEPTANCE OF QUALITY
No liabilities can be claimed for damages during or after the showertray has been installed
Prior to fitting the showertray, please check that it drains correctly.
Level the tray around the rim, place a large enough bowl under the tray and pour in water.
Due to surface tension, large droplets of water will remain but large pools should not be
evident (this excludes the rectangular shaped waste well of the showertray).
The connect2 showertray has been designed and developed to ensure
at least one of the two waste holes are not obstructed by floor joists
Joists running width of the tray
Where joists run parallel with the width
of the tray at least one waste hole will
always be clear for waste unit
joists under flooring
DUE TO THE WEIGHT & SIZE OF THE SHOWERTRAY
A MINIMUM OF TWO PERSONS ARE REQUIRED
TRAY MUST BE STORED FLAT ON A LEVEL SURFACE
PRIOR TO INSTALLATION
Where joists run parallel with the length of the tray and
both waste holes are obstructed, turn the tray 180 .
The unique offset position will ensure both will be free
HEALTH & SAFETY WARNING
TO MOVE AND INSTALL THIS ENCLOSURE
Joists running length of the tray
Rotate tray 180
to avoid joists
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for KUDOS Connect2 C2T90QSR
Summary of Contents for KUDOS Connect2 C2T90QSR
- Page 1 Please read these instructions throughout before installing as incorrect fitting will invalidate the guarantee. We recommend that a technically competent installer/s undertake the installation. If you are unsure about these instructions please contact Kudos Shower Products 01539 564040 PRIOR TO INSTALLATION The showertray must be checked thoroughly for defects.
- Page 2 IMPORTANT - fit only the waste unit/s supplied, CUT HOLE FOR WASTE fitting of any other wastes will nullify the guarantee. Refer to waste instructions in conjunction with these instructions. This showertray is suitable for installation on both cut hole wooden and solid floors.
- Page 3 RE-FIX FLOORBOARDS TO JOISTS LAY TRAY INTO POSITION Carefully lay tray into position against the walls. Tap down tray and check level of outer edges with spirit level. Showertray must be level. If fitting only one waste, carefully remove excess mix from redundant hole before it sets.
- Page 4 FIT WASTE COVER APPLY SILICONE SEALANT TO TRAY EDGES silcone sealant waste cover Fit waste cover into tray well, this is self-locating by means of Before tiling/panelling walls, any gap between the tray and walls concealed magnets. must be filled with silicone sealant flush to top of tray. FITTING BOTH WASTE UNITS TO TRAY Where joists run parallel with the length of the tray.
Need help?
Do you have a question about the Connect2 C2T90QSR and is the answer not in the manual?
Questions and answers