Table of Contents
Advertisement
Quick Links
Maintenance Manual
Read the instructions in this manual before beginning installation.
Save these instructions and refer to them for inspection,
maintenance, and troubleshooting information.
For questions regarding the operation, installation or maintenance of this product, visit
Product warranties and parts information may also be found under "Resources" on our website at bradleycorp.com/customerservice/warranty.
P20-225 Rev. D: ECO 24-15-009
© 2024 Bradley
Page 1 of 19
3/25/2024
Installation and
Verge
Verge™ Soap Dispenser
Verge™ Soap Dispenser - Metro Series (6-3300)
Verge™ Soap Dispenser
Verge™ Soap Dispenser
Table of Contents
Safety Information ............................................................................ 2
Supplies Required ............................................................................ 2
Components ..................................................................................... 3
Dimensions ....................................................................................... 4
Soap Spout Mounting ...................................................................... 5
Control Box Mounting ...................................................................... 6
Control Box & Soap Supply Connections ........................................ 7
Multi-Feed Soap Tank Assembly Mounting ..................................... 8
Soap Supply Connections ............................................................. 12
Power Supply Connections ............................................................ 16
Adding Soap to Multi-Feed Soap Tank Assembly ......................... 17
Operation Mode ............................................................................. 18
Cleaning and Maintenance for Soap Dispenser ............................ 19
Liquid Soap Recommendations & Dispenser Maintenance .......... 19
bradleycorp.com
Multi-Feed Soap
®
-
Crestt Series (6-3100)
-
Linea Series (6-3500)
-
Zen Series (6-3700)
Scan or click to view
Installation Guide for
Individual Automatic
Top-Fill Soap Dispensers
or call 800.BRADLEY (800.272.3539).
P.O. Box 309
Menomonee Falls, WI 53052 USA
800 BRADLEY (800 272 3539)
+1 262 251 6000
bradleycorp.com
Tank
Advertisement
Table of Contents
Summary of Contents for Watts Bradley Verge Crestt Series
-
Page 1: Table Of Contents
Installation and Maintenance Manual Verge Multi-Feed Soap ® Tank Verge™ Soap Dispenser Crestt Series (6-3100) Verge™ Soap Dispenser - Metro Series (6-3300) Verge™ Soap Dispenser Linea Series (6-3500) Verge™ Soap Dispenser Zen Series (6-3700) Table of Contents Safety Information ................2 Supplies Required ................ -
Page 2: Safety Information
Verge Multi-Feed Soap Tank ® Installation & Maintenance Safety Information Caution A DC plug-in adapter (supplied by Bradley) should be used in conjunction with the Bradley soap dispenser products. The DC plug-in adapter supplied by Bradley is 6V DC regulated. Direct connection to 120V/22V 50/60Hz could result in personal injury and will damage the sensor. -
Page 3: Components
Verge Multi-Feed Soap Tank Installation & Maintenance ® Components Power Supply Options AC Adapter Soap Spout Assembly Allen Key Silicone Washer Battery Pack Locking Tab w/Batteries Wing Nut AC Adapter Splitter Assembly Spacer Multi-Feed Control Box Soap Pump (Foam w/Tube) Soap Pump (Liquid w/Tube) Multi-Feed... -
Page 4: Dimensions
Verge Multi-Feed Soap Tank ® Installation & Maintenance Dimensions (mm) IMPORTANT: THE 6-3300, 6-3500 & 6-3700 SERIES SOAP DISPENSERS CANNOT BE MOUNTED DIRECTLY ON A DECK DUE TO THE REQUIRED 5-1/8" (130MM) MINIMIUM SENSOR CLEARANCE. THESE DISPENSERS MUST BE MOUNTED OVER A LAV BOWL. The 6-3100 Series soap dispenser can be mounted directly on a deck with the use of Crestt - Spout Spacer (P15-576). -
Page 5: Soap Spout Mounting
Verge Multi-Feed Soap Tank Installation & Maintenance ® Soap Spout Mounting Repeat this procedure for each soap spout assembly (maximum of 6 per system). Soap Spout Assembly Place the silicone washer under the soap spout assembly. Align with the Carefully insert the soap emboss on the bottom side supply &... -
Page 6: Control Box Mounting
Verge Multi-Feed Soap Tank ® Installation & Maintenance Control Box Mounting Locate the mounting position for the control box assembly. Top mounting holes need to be mounted between 4½" & 9½" from the top of the deck, and 2½" right or left of center of shank. 4¹⁄₂"... -
Page 7: Control Box & Soap Supply Connections
Verge Multi-Feed Soap Tank Installation & Maintenance ® Control Box & Soap Supply Connections Soap Supply Tube from Soap Spout Power Supply Assembly Connection Low Soap & Overflow Sensors NOTE: Not used in Multi-Feed installation. Verify the soap pump is positioned below the control box lever. -
Page 8: Multi-Feed Soap Tank Assembly Mounting
Verge Multi-Feed Soap Tank ® Installation & Maintenance Multi-Feed Soap Tank Assembly Mounting Before mounting the soap tank assembly, drill a 2-3/8" diameter hole through the deck that is 2‑3/8" Dia. positioned 2-1/2" from the adjacent back wall. Mounting Hole This will ensure proper clearance of the soap tank. - Page 9 Verge Multi-Feed Soap Tank Installation & Maintenance ® Carefully remove the fill port hub assembly from the soap tank assembly. Fill Port Hub LED and sensor wires are not shown in this Assembly view for clarity purposes. Mounting Nut U‑Cup Remove the mounting nut from the fill port hub assembly.
- Page 10 Verge Multi-Feed Soap Tank ® Installation & Maintenance Install Fill Port Hub Assembly on Lav Deck Install the fill port assembly through the 2-3/8" diameter hole in the lav deck. Fill Port Hub Assembly Spacer Position spacer and mounting bracket over fill port assembly and slide upward until spacer is in contact with under side of counter.
- Page 11 Verge Multi-Feed Soap Tank Installation & Maintenance ® Reconnect Soap Sensors & LED Connector LED Connector (White) Soap Overflow Sensor (Black) Low Soap Level Sensor (Red) Power Supply Connection Bradley • P20-225 Rev. D: ECO 24-15-009 3/25/2024...
-
Page 12: Soap Supply Connections
Verge Multi-Feed Soap Tank ® Installation & Maintenance Soap Supply Connections End Tank Configuration Installation See page 13 for an overview of the end tank configuration installation. Insert 3/8" diameter tubing into the elbow as shown. Connect the supply tube to the nearest control box, cutting the supply tube to the shortest length between units. - Page 13 Verge Multi-Feed Soap Tank Installation & Maintenance ® Bradley • P20-225 Rev. D: ECO 24-15-009 3/25/2024...
- Page 14 Verge Multi-Feed Soap Tank ® Installation & Maintenance Mid Tank Configuration Installation See page 15 for an overview of the mid tank configuration installation. Insert 3/8" diameter tubing into tee fitting as shown. Tubing will slide 3/4" into the fittings. Soap Supply Tube Soap supply valve is...
- Page 15 Verge Multi-Feed Soap Tank Installation & Maintenance ® Bradley • P20-225 Rev. D: ECO 24-15-009 3/25/2024...
-
Page 16: Power Supply Connections
Verge Multi-Feed Soap Tank ® Installation & Maintenance Power Supply Connections The multi-feed soap tank assembly and each of the control boxes require a power supply connection. The power supply can be a Bradley supplied battery pack, a single AC adaptor, or an AC adapter splitter assembly kit (see page 3), depending on the selection made at time of purchase. -
Page 17: Adding Soap To Multi-Feed Soap Tank Assembly
Verge Multi-Feed Soap Tank Installation & Maintenance ® Adding Soap to Multi-Feed Soap Tank Assembly When the soap level is at approximately 25% capacity, the LED indicator on the fill port hub assembly will flash red, indicating low soap levels. Soap tank capacity is 166.5 oz (5026 mL). -
Page 18: Operation Mode
Verge Multi-Feed Soap Tank ® Installation & Maintenance Operation Mode Operation mode is the normal dispensing mode automatically activated when the soap dispenser is in use. All of the sensors are active in this mode. While in operating mode: • Soap is activated when IR sensor is triggered. •... -
Page 19: Cleaning And Maintenance For Soap Dispenser
Verge Multi-Feed Soap Tank Installation & Maintenance ® Cleaning and Maintenance for Soap Dispenser Wipe top and underside of soap dispenser with a mild neutral based cleaner. Dry with a soft cloth to avoid micro scratches in the soap dispenser finish and sensor plate. Liquid Soap Recommendations &...