Alloy Leak Sensor+ Next-generation 800 Series Quick Start Manual

Hide thumbs

Table of Contents

Quick Links

Download this manual

Alloy Leak Sensor+

Quick-Start Guide

Table of Contents

Need help?

Do you have a question about the Leak Sensor+ Next-generation 800 Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Alloy Leak Sensor+ Next-generation 800 Series

Page 1 Alloy Leak Sensor+ Quick-Start Guide...
Page 2 MEET YOUR ALLOY LEAK SENSOR+ Next-generation 800 series leak sensor with longer battery life. This product can be operated in any Z-Wave network with other Z-Wave ® ® certified devices from other manufacturers. All mains operated nodes within the network will act as repeaters regardless of vendor to increase...
Page 3 TAMPER button INCLUSION/ADD button HUMIDITY & TEMPERATURE sensor WALL MOUNTING plate...
Page 4: Installation
- 2 x Dry wall screws - Safety user manual 1.1. WALL MOUNTING Drill two holes and screw the Alloy Leak Sensor+ back plate onto the wall. Make sure that it is leveled. The Wall-plate allows for simple, error-free installation.
Page 5 1.2. POWER UP Alloy Leak Sensor+ will turn ON when you plug Leak detect probe or sensor wire. Alloy Leak Sensor+ won’t go into sleep state until: included, and mounted on a wall plate. Warning! When Alloy Leak Sensor+ is turned ON, it remains ON until manually included or included through SmartStart, and properly mounted (battery drain).
Page 6 SMARTSTART This device supports SmartStart. The QR code can be found on the Alloy Leak Sensor+, below the lid and on the packaging. The device will enter SmartStart if the device is not included in the network after power up. And if the device is not included successfully during 10 seconds, it will enter sleep mode.
Page 7: Power Down
Hold the inclusion button for 7 seconds and Alloy Leak Sensor+ will Factory reset. Alloy Leak Sensor+ will beep and red LED will flash 4 times to indicate the Factory reset was successful. Please use this procedure only when the network’s primary controller is missing or otherwise inoperable.
Page 8 1 second. 1.9. TAMPER Alloy Leak Sensor+ will stay awake as long as it’s not mounted, i.e., until the tamper button isn’t pressed. It will beep 5 times every 2 minutes to indicate incorrect installation. When correctly installed, the Alloy Leak Sensor+ will beep once.
Page 9: Specifications
2.0. | SPECIFICATIONS RADIO FREQUENCY MODEL NUMBER 908.40MHz, 916.00MHz - US, als+zw8us RADIO PROTOCOL 921.00 MHz - US ® Z-Wave RANGE Z-Wave Plus ® Up to 45m (147 ft) indoors (depending POWER SUPPLY on the building structure), and up to 60m CR-2/3 battery (196 ft) outdoors.
Page 10 COMMAND CLASSES COMMAND CATEGORY SUPPORTED • DT:13.11.0001.1 Z-Wave Plus ® Command classes Device Type Specification • Main Endpoint The Notification Sensor Device Type MUST use the following Device Classes: • GENERIC_TYPE_SENSOR_NOTIFICATION 4.6.3.1 Generic and Specific Device Class (0x07) • SPECIFIC_TYPE_NOTIFICATION_SENSOR (0x01) •...
Page 11: Configuration Parameters
CONFIGURATION PARAMETERS CURRENT CONFIGURATION PARAMETER SIZE AVAILABLE DEFAULT PARAMETERS NUMBER (BYTE) SETTINGS VALUE 1. Alarm Duration Time This configuration value can be used to set the total duration of the audio (buzzer) and visual warning (LED) when flood / water leakage is detected. If this 0 ~ 120 configuration is set to ‘0’, both warnings will be active until water leakage is...
Page 12 CURRENT CONFIGURATION PARAMETER SIZE AVAILABLE DEFAULT PARAMETERS NUMBER (BYTE) SETTINGS VALUE 5. Disable Water Leakage Detection If this configuration value is set to ‘0’, it will disable the flood detection function. 6. Disable Audio / Beep Alarm If this configuration value is set to ‘0’, it will disable the audible buzzer / beeping when flood is detected.
Page 13 10. Delay flood notification feature Delay sending flood notification. Unit s (seconds). 0 ~ 255 Value 0 disables the delay. 11. Flood alert re-send interval Indicates a time interval for re-sending 1 ~ 255 flood notification. Unit minutes Value 0 disables the re-send feature.. First 4 parametres combined define the flood warning alarm behavior like this:...
Page 14 1 associate node. Group 1 is a Lifeline Group; all nodes which are associated in this group will receive the messages sent by the Alloy Leak Sensor+ through Lifeline. Group 2 is a controlling group. All nodes associated in this group will be controlled through the BASIC_SET command by the Alloy Leak Sensor+ when it detects a water leakage event.
Page 15 STATE_IDLE (0x00) WAKE UP COMMAND CLASS Alloy Leak Sensor+ stays in sleep state for the majority of time in order to conserve battery life. The minimum wakeup interval is 20 sec. The maximum wakeup interval is 86400 sec (24 Hours). Allowable min step among each wake-up interval is 60 seconds, such as 1860 sec, 1920 sec,1980 sec…...
Page 16 BATTERY COMMAND CLASS The users can also inquire about the battery status of the Alloy Leak Sensor+ by sending the BATTERY GET command. Once the Alloy Leak Sensor+ receives the command, it will return the BATTERY REPORT command. The Alloy Leak Sensor+ will send...
Page 17: Led Indicator
LED INDICATOR Device action LED color LED display interval Inclusion/ Flashing every 2 seconds until included adding Blue Battery half full (on device Two 1s flashes power on) Inclusion/add Flash 6 times at 500 ms intervals success Green Battery full (on device power Two 1s flashes Wake up...
Page 18 • Do not install the Alloy Leak Sensor+ near any water vapor or smoke. • Do not submerge the Alloy Leak Sensor+ or the Leak detect probe in water. • Do not attempt to replace the battery, it can be replaced only by a certified installer.
Page 19: Disposing And Recycling Your Product
(Applicable in countries with separate collection systems) At Alloy Home, we understand and are committed to reducing any impact our operations and products may have on the environment. To minimize this impact Alloy Home designs and builds its products to be as environmentally friendly as possible, by using recyclable, low toxic materials in both products and packaging.
Page 20 (Applicable in countries with separate collection systems) At Alloy Home, we understand and are committed to reducing any impact our operations and products may have on the environment. To minimize this impact Alloy Home designs and builds its products to be as environmentally friendly as possible, by using recyclable, low toxic materials in both products and packaging.
Page 21: One (1) Year Limited Warranty
Warranty Period, then as your sole remedy (and Alloy Home’ sole liability), Alloy Home will at its option either 1) repair the defect at no charge, using new or refurbished replacement...
Page 22 Product that is used commercially or for a commercial purpose, in each case as determined by Alloy Home. EXCEPT FOR BODILY IN JURY, ALLOY HOME SHALL N OT BE LIABLE FOR (I) AN Y LOST PROFITS, COST OF PROCUREMENT OF SUBSTITUTE PRODUCTS, OR...
Page 23 To exercise your rights under this warranty, please follow the instructions above under the heading “Obtaining Service”, or contact Alloy Home, LLC, 8665 E. Hartford Drive, Suite 200, Scottsdale, AZ 85255. Alloy Home Hub is a registered trademark of Alloy...
Page 24: Declaration Of Conformity
6.0. | DECLARATION OF CONFORMITY We, Alloy Home, LLC, 8665 E. Hartford Drive, Suite 200, Scottsdale, AZ 85255, declare that the product Alloy Home Hub is in compliance with all the technical regulations applicable to the product within the scope of Council Directives 2014/53/EU.
Page 25 3. Adapter shall be installed near the equipment and shall be easily accessible. 4. The plug considered as disconnect device of an adapter. 5. The device complies with RF specifications when the device used at 0mm from your body. RF output power: This product can be used across EU member states. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Page 26 • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCC’s RF Exposure guidelines, this equipment should be installed and operated at distance greater than 20 cm from your body.
Page 27 applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) L’appareil ne doit pas produire de brouillage; (2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Page 28 make your home smart...

This manual is also suitable for:

Als+zw8us