Table of Contents
Advertisement
Quick Links
B B I I O O K K O O P P R R I I K K f f t t . .
HACO, spol. s r.o.
BIOKOPRI Kft.
Add.:6500 Baja,Mártonszállási út 10.
Tel.: 0036 79 / 468-890 or +36 79 / 320-058
Svobody 826/88
Add.:6500 Baja,Mártonszállási út 10.
Web:www.biokopri.hu
460 15 Liberec 15
Tel.: 0036 79 / 468-890 or +36 79 / 320-058
Email: info@biokopri.hu
Czech Republic
Web:www.biokopri.hu
Email: info@biokopri.hu
tel. / phone: +420 482 750 620 - 21
fax: +420 482 750 619
Instruction Manual
Single Room
Energy Recovery
Ventilator
DYAP06K01201
Technical Manual of FALCON
Single Room Heat Recovery Ventilator
Model No.: SRJ 3W
Models:
FALCON HRV SOLO 64
Attention
Please read this manual carefully before using the equipment. For safety precautions,
please read carefully before construction or use, and use the equipment safely.
Advertisement
Table of Contents
Summary of Contents for Haco SRJ 3W
- Page 1 Single Room Heat Recovery Ventilator Ventilator B B I I O O K K O O P P R R I I K K f f t t . . Model No.: SRJ 3W HACO, spol. s r.o. BIOKOPRI Kft.
-
Page 2: Table Of Contents
Content SAFETY REQUIREMENTS INTRODUCTION PACKING LIST MAIN TECHNICAL PARAMETERS DESIGN AND OPERATION INSTALLATION DRAWING OPERATION MODES VENTILATOR INSTALLATION FUNCTION DESCRIPTION REMOTE CONTROLLER MASTER-SLAVE LINKAGE SYNCHRONIZATION FUNCTION MASTER UNIT SETTINGS SLAVE UNIT SETTINGS MASTER AND SLAVE UNITS RESET AND CANCELLATION IOT NETWORKING FEATURES WIFI CONNECTION STEPS MAINTENANCE STORAGE AND TRANSPORTATION RULES... -
Page 3: Safety Requirements
SRJ 3W. understand the hazards involved. operation of open flue gas appliances should... -
Page 4: Introduction
Instruction Manual Instruction Manual for the user and the qualified installer for the user and the qualified installer INTRODUCTION Do not use damaged Do not wash the ventilator equipment or conductors with water. Protect the This user’s manual includes technical to connect the ventilator ventilator electric parts description operation, installation and... -
Page 5: Main Technical Parameters
Instruction Manual Instruction Manual for the user and the qualified installer for the user and the qualified installer MAIN TECHNICAL PARAMETERS • The ventilator is designed for indoor application with the ambient temperature ranging from Voltage 100-240 V AC -20°C (-4F) to +50°C (+122F) and relative humidity below 80%. •... -
Page 6: Design And Operation
Instruction Manual Instruction Manual for the user and the qualified installer for the user and the qualified installer DESIGN AND OPERATION INSTALLATION DRAWING • The ventilator consists of a telescopic air duct with adjustable length regulated by the position Silicone waterproof circle of the inner air duct inside the outer air duct, the ventilation unit, and the ventilation hood. -
Page 7: Ventilator Installation
Instruction Manual Instruction Manual for the user and the qualified installer for the user and the qualified installer OPERATION MODES VENTILATOR INSTALLATION Ventilation Mode. The ventilator runs in the air extract or air supply mode with a set speed. In 1. -
Page 8: Function Description
Instruction Manual Instruction Manual for the user and the qualified installer for the user and the qualified installer FUNCTION DESCRIPTION 4. Fix the fan and the bracket by the nut, put 6. Install the fan on the wall surface. fix the fan the fan into the inner duct, mark the drilling to the bracket by the nut. -
Page 9: Master-Slave Linkage Synchronization Function
Instruction Manual Instruction Manual for the user and the qualified installer for the user and the qualified installer MASTER-SLAVE LINKAGE SYNCHRONIZATION FUNCTION MASTER UNIT SETTINGS 1. Feed power to the ventilator but in OFF state, use a needle to press the Reset button twice Master Unit Suggested maximum distance 15 meters Slave Unit... -
Page 10: Slave Unit Settings
Instruction Manual Instruction Manual for the user and the qualified installer for the user and the qualified installer SLAVE UNIT SETTINGS MASTER AND SLAVE UNITS RESET AND CANCELLATION 1. The same steps as the MASTER setting. Feed power to the ventilator but in the OFF state, use a Feed power to the ventilator but in OFF state, use a needle to press the Reset button over 10 needle to press the Reset button twice quickly (as shown in the figure). -
Page 11: Iot Networking Features
Instruction Manual Instruction Manual for the user and the qualified installer for the user and the qualified installer IOT NETWORKING FEATURES WIFI CONNECTION STEPS Scan the QR code and search “Smart Vent” from 1. Before linkage connection, please connect the Google Play or App store to download the App. - Page 12 Instruction Manual Instruction Manual for the user and the qualified installer for the user and the qualified installer 3. Open the mobile app, enter the operation 4. At this time, the app receives the signal 5. Find the same wifi signal as the mobile 6.
-
Page 13: Maintenance
Instruction Manual Instruction Manual for the user and the qualified installer for the user and the qualified installer MAINTENANCE Clean the filter as often as it gets dirty, but at least 3-4 times a year. Clean Clean the impeller blades. Use a soft Disconnect The Ventilator From the filters, let them get dry, and install the dry filters inside the air duct brush, doth or a vacuum cleaner to clean... -
Page 14: Troubleshooting
Instruction Manual for the user and the qualified installer TROUBLESHOOTING Fault Possible reasons Fault handling Make sure that the ventilator is properly No power supply. connected to the power and make any corrections, The fan does not if necessary. Start up during the Turn the ventilator off.