1. Manuals
  2. Brands
  3. CE+T Power Manuals
  4. Racks & Stands
  5. T306730001
  6. System manual

CE+T Power T306730001 System Manual

Tsi manual bypass rack 20a -1u
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
S
Y
S
T
E
M
M
A
N
U
A
L
S
Y
S
T
E
M
M
A
N
U
A
L
S
Y
S
T
E
M
M
A
N
U
A
L
TSI Manual Bypass Rack 20A -1U
T306730001
TSI_MBP Rack User Manual_Rev06-Sept-2015
This document is subject to modification without prior notice from the manufacturer.
The present equipment is protected by several international patents and trademarks.

Advertisement

Table of Contents
loading

Summary of Contents for CE+T Power T306730001

  • Page 1 TSI Manual Bypass Rack 20A -1U T306730001 TSI_MBP Rack User Manual_Rev06-Sept-2015 This document is subject to modification without prior notice from the manufacturer. The present equipment is protected by several international patents and trademarks.

  • Page 2: Table Of Contents

    Tables of contents SYSTEM MANUAL ..............1 0 Safety Recommendations ............... 2 1 Introduction ..................3 1.1. Overview: ............................3 1.2 Product Description: ........................3 2 Product Constitution ............... 5 2.1 TSI MBP Rack Identification Plate ....................5 2.2 Package Includes .......................... 5 3 Installation ..................

  • Page 3: Safety Recommendations

    0 Safety Recommendations Your safety is our major concern. Read carefully all safety aspects listed in this manual prior any intervention on the appliance. The manufacturer declines all responsibilities if equipment has not installed by skilled technician and in a proper way according to local safety regulation and as it is described herein. TSI Manual Bypass Rack is not supplied with internal disconnect devices.

  • Page 4: Introduction

    1 Introduction This document applies to the TSI System. For product description, please refer to related document. The information provided in this manual covers single phase Manual Bypass Rack 20A 1U Unit, their basic functions, operating procedures, options available and emergency situations. It also includes information electrical connections, cabling,...
  • Page 5 The MBP unit provides an isolation path of power for Inverter system for preventive maintenance or service. There are both normal and Bypass modes of operation as described as below 1. Under normal operation, the Mains AC Input flows through the MBP unit to the Inverter/UPS and then out to the Connected Loads.

  • Page 6: Product Constitution

    Please check that operating manual version you are reading is corresponding to TSI version running in your installation. TSI Manual Bypass Rack for the Bypass of UPS/TSI Inverter. Part Description and Number: TSI Manual Bypass Rack 20A – 1U T306730001 2.1 TSI MBP Rack Identification Plate 2.2 Package Includes  TSI Manual Bypass Rack 20A-1U ...

  • Page 7: Installation

    3 Installation Caution: Installation and commissioning must be done and conducted by trained people fully authorized to act on installation. 3.1 Overview The Manual Bypass Racks are foreseen to be recessed into an electrical cabinet of 19” standard. 3.2 System dimensions The picture shows the front, side and rear view of the MBP Rack.

  • Page 8: Fixing

    FRONT VIEW SIDE VIEW REAR VIEW 3.3 Fixing A full range of accessory is ready made to allow easy integration of the TSI MBP in almost any kind of standard cabinets. Among other we provide fixing set for:  19” – 600mm depth cabinets (most standard solution, which is supplied by default) ...

  • Page 9: Wiring

    3.4 Wiring Caution: The TSI MBP Rack does not include any protecting and/or disconnecting devices on AC input. Before any intervention on the TSI MBP Rack, operator has to make sure that power is removed from AC input mains. All breakers, cables and wires must be CE and classified for min 90°C (194°F) operation All DC cables and alarm cables as well must be kept minimum 10mm away AC cables...

  • Page 10: Ac Input Connection Of Tsi Inverter

    3.4.1.2. AC input connection of TSI Inverter For single-phase equipment, the disconnect device shall disconnect both poles simultaneously. Except that a single-pole disconnect device can be used to disconnect the line conductor where it is possible to rely on the identification of the neutral in the AC MAINS SUPPLY. 230 Vac model AC breaker Cable size...

  • Page 11: Ac Connection Of Mbp

    3.4.1.4. AC Connection of MBP Four wago connectors available for the AC Connection 1) The AC Mains Input to Manual Bypass Rack (PL1) will be connected directly through AC Breaker. 2) The AC/TSI OUT (PL2) is the output for the load from the MBP. 3) The Inverter TSI Out (PL3) in the MBP will be connected to TSI Inverter (AC OUT).

  • Page 12: Use Of Manual Bypass

    4 Use of Manual Bypass Caution Before connecting any power DC or AC to the system, Make sure you have followed instructions of previous section “Installation”. Equipment does not require any particular maintenance, but when environment is dirty, before cleaning, inverters can be removed only after action on Manual By-Pass.
  • Page 13 MBP ON: 1. Switch ON S1 - Mains input is ready for connecting to the output 2. Switch OFF S2 - TSI OUTPUT available at the output connector is diverted to the Mains Input supply 3. Switch OFF S3 - AC Supply to the inverter is cut off.(Inverter may be ON due to DC SUPPLY) 4.

  • Page 14: Troubleshooting

    The purpose of remote emergency stop connector is to switch off the inverter output under the emergency conditions. The Remote emergency connector (PL6) has a parallel connection with the emergency stop push button of the MBP Rack. The customer can operate the emergency stop push button in the rack directly to stop the Inverter output in case of emergency or can take the connection from the connector PL6 and connect to the same type of push button switch arrangement to operate in a remote place.

  • Page 15: Commissioning

    Check if Manual By-Pass sequence is not engaged Check if output Manual By-Pass switch (S2) is ON Check if the AC output breaker is ON Check if no short circuit is present on the output Check status on inverter Refer T2S or T1S operating manual for additional troubleshooting 6 Commissioning Caution: Installation and commissioning must be done and conducted by trained...

  • Page 16: Commissioning

    (check individual connection) Check cross section and breaker protection for AC input and output cables AC input connection properly done (L+N+PE) on input terminal of Inverter and other end connected to PL4 connector of MBP Rack (use cable D1) AC output connection properly done (L+N+PE) on output terminal of Inverter and other end connected to PL3 connector of MBP Rack (use cable C1) PE connection properly done even if mains is not connected AC/TSI Inverter output (PL2) of the MBP Rack connected to the load output...

  • Page 17: Alarm Test

    Switch OFF system and start on DC only Test on load (if available) 6.3 Alarm test DEFAULT Switch ON AC input and DC input and check that no alarm are present Switch ON S1 Manual by-pass (AC IN) Switch OFF AC input (commercial power failure) and check the alarm according to the configuration Switch OFF DC input (DC power failure) and check that the alarm according to the configuration...

  • Page 18: Technical Data Sheet

    7 Technical Data sheet NVIRONMENT ENERAL <1500m Connection I/O Wago connector Altitude above sea Protected against inversion of polarity n x 1500VA -20 to 50 °C Ambient temperature (**) Pmax at 100% LOAD Enclosure IP20 Derating up to 65°C -40 to 70 °C Storage temperature AC I NPUT...

  • Page 19: Schematic Drawing

    8 Schematic Drawing...

Table of Contents