Advertisement
3. SPECIFICATION
MODEL NO.: ............................................. EVBT700.V2
Capacity: .............................................................. 700kg
Maximum Platform Height: ............................... 1500mm
Minimum Platform Height: .................................. 445mm
Platform Length: ............................................... 1220mm
Platform Width: .................................................. 610mm
Wheel Size: ..................................................... Ø125mm
4. ASSEMBLY
NOTE: The trolley comes fully assembled except for the handle
assembly and foot-pedal. Refer to Parts List.
4.1.
HANDLE
4.1.1.
Fit the handle to the frame using the supplied screws and washers.
4.2.
FOOT-PEDAL
4.2.1.
Insert the foot-pedal onto the drive shaft and fix in position using
the supplied fixings.
5. OPERATION
WARNING! Ensure you read, understand and follow the safety instructions. Ensure all Health and Safety, local authority, and general
‰
workshop practice regulations and recommendations are strictly adhered to when lifting or moving heavy loads. The lifting or
movement of heavy loads may be dangerous if not undertaken correctly.
‰
5.1.
RAISING THE PLATFORM
NOTE: Ensure that any obstructions are removed.
5.1.1.
When in position for lifting the platform, ensure that the castor wheels are locked in position.
5.1.2.
Pump the foot-pedal to raise the platform to the required height. If fully extended, the safety bars can be lowered into position to
prevent the platform from dropping.
5.2.
LOWERING THE PLATFORM
WARNING! Ensure the load will not foul on anything, and is clear of your hands and the handle when lowering.
‰
5.2.1.
If used, disconnect the safety bars by raising the table slightly and turning the bars back to the resting position.
5.2.2.
Squeeze the trigger to lower the platform.
5.2.3.
Unlock the castor wheels and transport the load to the required destination.
NOTE: With or without a load, always transport the truck with platform in its lowest position. When not in use, store the truck
with the platform in the lowest position.
6. MAINTENANCE
When the truck is not in use, the platform must be in the lowest position to minimise ram and piston corrosion.
9
Keep the truck clean and wipe off any oil or grease. Lubricate all moving parts with acid free oil.
9
DO NOT use truck if believed to have been subjected to abnormal load or shock load. Inspect and if necessary take
8
appropriate action.
Periodically check the pump piston and piston rod for signs of corrosion. Clean exposed areas with a clean oiled cloth.
9
IMPORTANT: Only fully qualified personnel should attempt maintenance or repair of the truck and it's hydraulic system.
The oil cylinder is a sealed unit and must not be accessed. For service contact your authorised dealer.
9
WARNING! Only a good quality hydraulic oil, such as Sealey hydraulic jack oil must be used, DO NOT use brake fluid.
‰
IMPORTANT: NO RESPONSIBILITY IS ACCEPTED FOR INCORRECT USE OF THE TRUCK.
Owing to their size and weight, hydraulic products should ideally be repaired by local service agents. We have service / repair agents in
9
most parts of the UK. Before returning your product please call our technical helpline on 01284 757505 for advice and troubleshooting
9
guidance.
Regularly grease the hinge points (fig.1).
9
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers
and dispose of the product and fluids according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call
our technical team on technical@sealey.co.uk or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
© Jack Sealey Limited
fig.1
sales@sealey.co.uk
Original Language Version
Lowering
Lever
Lifting
Foot Pedal
Grease nipple
REGISTER YOUR
PURCHASE HERE
www.sealey.co.uk
EVBT700.V2
Issue 1
04/04/23
Advertisement
