Advertisement
Quick Links
C
Net to Net Technologies strongly recommends the use of proper electrostatic discharge (ESD) precautions when
AUTION
handling this equipment.
1.0 INSTALLATION
1.1 Unpack and Inspect the Equipment
The following components should be included:
1 UIM-1000F
4 #6 Phillips Panhead Nylon Locking Screws
2 #6 Phillips Beige Flathead Screws
If there is visible damage, do not attempt to install the UIM-1000F; contact Customer Support at 1-
877-638-2638 (1-603-427-0600 for international customers) or support@nettonet.com.
1.2 Install the UIM-1000F on a Multiplexer Uplink Module (MUM)
An uplink interface module (UIM) provides the upstream network connection, via a MUM, for Net to
Net Technologies' IP DSLAMs; neither an IP DSLAM nor a MUM can function without a UIM.
N
The MUM2000-2 is currently Net to Net's only multiplexer uplink module capable of supporting the UIM-1000F.
OTE
Select a port on the MUM2000-2 for installation of the UIM-1000F: either port (1 or 2) may be
used. Although not required for operational purposes, if redundancy is desired two UIMs may
be installed on a MUM2000-2, one in each port.
Remove the blanking plate from the selected port.
C
Blanking plates should be stored for possible future use: if a UIM-1000F is removed from the
AUTION
MUM2000-2, it must be replaced with either another UIM or a blanking plate. DO NOT
OPERATE THE MUM2000-2 WITH AN OPEN UIM PORT.
Carefully slide the faceplate of the UIM-1000F under the lip of the MUM2000-2 faceplate at
the selected port opening such that the UIM-1000F circuit board is facedown and the label
220-0000080 rev 01
UIM-1000F
Fiber Optic Gigabit Ethernet Uplink Interface Module
Installation Instructions
Advertisement
Summary of Contents for Net to Net Technologies UIM-1000
- Page 1 Fiber Optic Gigabit Ethernet Uplink Interface Module Net to Net Technologies strongly recommends the use of proper electrostatic discharge (ESD) precautions when AUTION handling this equipment. 1.0 INSTALLATION 1.1 Unpack and Inspect the Equipment The following components should be included: 1 UIM-1000F 4 #6 Phillips Panhead Nylon Locking Screws 2 #6 Phillips Beige Flathead Screws...
- Page 2 shows through the MUM2000-2 port opening with the UIM-1000F model name along the right- hand edge. Ensure that the mounting holes on the UIM-1000F are lined up with the corresponding pems on the MUM2000-2 circuit board and that the board-to-board connector key pins are properly aligned.
- Page 3 2.1.1 Current SFP Options 2.1.1.1 SFP-SMF10 Net to Net's small form factor pluggable, single-mode fiber module is required for single- mode fiber connections with the UIM-1000F. The SFP-SMF10 supports 1000Base-LX (long haul) connections with a maximum reach of 10 kilometers. 2.1.1.2 SFP-MMF Net to Net's small form factor pluggable, multi-mode fiber module is required for multi- mode fiber connections with the UIM-1000F.
- Page 4 3.2 Regulatory Compliance for Class A Equipment The following regulatory compliance information applies to the UIM-1000F as mounted on a MUM2000-2 and installed in one of Net to Net Technologies' IP DSLAMs. 3.2.1 US Federal Communications Commission (FCC) Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.