Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for CTI Rogue-X NVMe Breakout
Summary of Contents for CTI Rogue-X NVMe Breakout
- Page 1 Rogue-X NVMe Breakout CTIM-00022 Revision 0.00 2023-10-17...
-
Page 2: Table Of Contents
Rogue-X NVMe Breakout Users Guide www.connecttech.com TABLE OF CONTENTS Table of Contents ........................2 Preface ............................3 Disclaimer ............................3 Customer Support Overview ......................3 Contact Information ......................... 3 Limited Product Warranty ....................... 4 Copyright Notice ..........................4 Trademark Acknowledgment ......................4 ESD Warning ............................ -
Page 3: Preface
Rogue-X NVMe Breakout Users Guide www.connecttech.com PREFACE Disclaimer The information contained within this user’s guide, including but not limited to any product specification, is subject to change without notice. Connect Tech assumes no liability for any damages incurred directly or indirectly from any technical or typographical errors or omissions contained herein or for discrepancies between the product and the user’s guide. -
Page 4: Limited Product Warranty
Rogue-X NVMe Breakout Users Guide www.connecttech.com Limited Product Warranty Connect Tech Inc. provides a one (1) year Warranty for this product. Should this product, in Connect Tech Inc.'s opinion, fail to be in good working order during the warranty period, Connect Tech Inc. will, at its option, repair or replace this product at no charge, provided that the product has not been subjected to abuse, misuse, accident, disaster or non-Connect Tech Inc. -
Page 5: Esd Warning
Rogue-X NVMe Breakout Users Guide www.connecttech.com ESD Warning Electronic components and circuits are sensitive to ElectroStatic Discharge (ESD). When handling any circuit board assemblies including Connect Tech COM Express carrier assemblies, it is recommended that ESD safety precautions be observed. ESD safe... -
Page 6: Introduction
Users Guide www.connecttech.com INTRODUCTION Connect Tech’s Rogue-X NVMe Breakout has been developed for when one M.2 storage slot is not enough. This product is ideal for adding additional storage capacity for embedded vision and multi- camera applications. Product Features and Specifications... -
Page 7: Product Overview
Rogue-X NVMe Breakout Users Guide www.connecttech.com PRODUCT OVERVIEW Block Diagram Document: CTIM-00022 Page 7 of 12 Date: 2023-10-17 Revision: 0.00... -
Page 8: Connector Summary & Locations
Rogue-X NVMe Breakout Users Guide www.connecttech.com Connector Summary & Locations Designator Description Rogue-X (AGX103) connector M.2 M-Key (NVMe) connector 12V Barrel Jack input, 2.1mm centre positive Jumper Summary & Locations Designator Description GPIO 0.1” header LED Summary Designator Description D1, D2 … D8 GPIO LEDs M.2 connector (P2) activity... -
Page 9: Detailed Feature Description
Rogue-X NVMe Breakout Users Guide www.connecttech.com 12V power good Voltage regulator fault 3.3V good DETAILED FEATURE DESCRIPTION Connectors & Jumpers Rogue-X Connector Function Rogue-X Connector Location Type 51 Position Receptacle Connector Surface Mount, Right Angle Connector Part Number: FI-RE51S-HF-R1500 Manufacturer: JAE Electronics... - Page 10 Rogue-X NVMe Breakout Users Guide www.connecttech.com where x = 2,3,4 for 20,30,40cm versions Pinout Connector Pins Function / Description 1,3,5,9,12,15,18,21,24,28, 31,34,37,40,43,47,49,51 GPIO #5 GPIO #6 GPIO #4 GPIO #3 PCIe PERST# active low reset signal PCIe Ref Clkp PCIe Ref Clkn...
-
Page 11: M.2 M-Key - Nvme
Rogue-X NVMe Breakout Users Guide www.connecttech.com GPIO #7 Notes Mating cable is rated to 0.3A per contact for 0.9A total GPIO 1-6: Pulled up to 3.3V w/1K resistor, 25mA open-drain output GPIO 7-8: Pulled up to 5V w/1K resistor, 25mA open-drain output M.2 M-Key - NVMe... -
Page 12: Typical Installation
5. Power on Rogue-X POWER CONSUMPTION & THERMALS The Rogue-X NVMe breakout has an operating temperature range of -40°C to 85°C. Please note that NVMe modules will have thermal preoperties separate to that of the NVMe breakout. MECHANICAL DRAWINGS & MODELS Links to models and drawings will be included in a future document update.
Need help?
Do you have a question about the Rogue-X NVMe Breakout and is the answer not in the manual?
Questions and answers