Advertisement
Quick Links
Advertisement
Summary of Contents for AMobile SM1200 EVK
- Page 1 SM1200 EVK Development Kit Quick Inatallation Guide Version 1.0 2023.10...
- Page 3 User Guide Revision History Version Release Time Description 2023.10 Initial release Copyright Copyright© 2023 All Rights Reserved. This document contains proprietary information protected by copyright. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.
-
Page 4: Table Of Contents
User Guide Table of Contents 1 Packing List .......................3 2 SM1200 EVK System Setup..................4 3 SM1200 EVK Board Overview ..................5 4 Camera Installation....................7 5 MIPI DSI Panel FPC and Touch Cable Connection ...........7 6 How to Power Up the System..................8 7. -
Page 5: Packing List
1. Packing List SM1200 EVK Packing List Item# Item Name Remark Usage SM1200 EVK DEV KIT BOX PACKAGE SM1200 SoM Board (MB) SM1200 CB100 Carrier Board 8" Touch Display w/ FPC FPC Installed 13MP Camera FPC, SONY IMX214 SM1200 Heat Sink Plate... -
Page 6: Sm1200 Evk System Setup
User Guide Preface 2. SM1200 EVK System Setup The SM1200 EVK, the entire peripherals include: 1. 8" Touch panel with FPC pre-installed 2. Camera FPC x1 3. M.2 Wi-Fi 6/BT5.2 module pre-installed with 2 antenna cable sets 4. Power adapter with power cord plug 5. -
Page 7: Sm1200 Evk Board Overview
Audio line 40-pin Expansion Header Micro SD card HDMI RX Out/In (I2C/GPIO/UART/SPI) 20-pin Expansion Header (GPIO) Figure 3-1 SM1200 EVK Top View M.2 5G Module M.2 Wifi6 / BT Module M.2 SSD Module Figure 3-2 SM1200 EVK Bottom View - 5 -... - Page 8 User Guide SIM Card Slot Figure 3-3 SM1200 EVK Bottom View A/V Intput I/F A/V Output I/F Peripheral MIPI CSI 4L eARC RX MIPI DSI 4L eDP TX UART HDMI RX PDM In DP TX HDMI TX SDIO S/PDIF In...
-
Page 9: Camera Installation
User Guide 4. Camera Installation Please connect and snap-in the Camera FPC onto the connector as indicated by the red circle location. Figure 4-1 D2/D6 Board Installation 5. MIPI DSI Touch Panel FPC Cable Connection Installation procedure: Step1. Find the MIPI display connector and turn up the flip cover. Step2. -
Page 10: How To Power Up The System
User Guide 6. How to Power Up the System Procedure: Step1. After installing camera and display, continue to install the power cord plug to the DC Jack and LAN cable to RJ45 port. Step2. Use a jumper or tweezers to short the two pins few second to power up the system Step3. -
Page 11: Debug Pins Definition
User Guide 7. Debug Pins Definition ADB TYPC-C USB port Serial RX Serial TX - 9 -... -
Page 12: Exhibit 1 Terms And Conditions
User Guide Exhibit 1 Terms and Conditions Your access to and use of this document and the information contained herein (collectively this “Document”) is subject to your (including the corporation or other legal entity you represent, collectively “You”) acceptance of the terms and conditions set forth below (“T&C”). By using, accessing or downloading this Document, You are accepting the T&C and agree to be bound by the T&C.
Need help?
Do you have a question about the SM1200 EVK and is the answer not in the manual?
Questions and answers