Advertisement
1.4.
OPERATIONAL PRECAUTIONS
The heater must only be used by people who have read these instructions and have been trained in its use.
9
DO NOT obstruct the air inlet and outlet sections of the heater.
8
WARNING: In order to avoid overheating DO NOT cover the heater.
‰
DO NOT use the heater without the grille fitted.
8
DO NOT use if the heater has been dropped.
8
DO NOT use if there are visible signs of damage to the heater.
8
DO NOT touch the heater casing or grille when first switched off, as these will be very hot and will take time to cool.
8
NOTE: Children of less than 3 years should be kept away unless supervised continuously.
Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its
intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and
understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or
perform user maintenance.
CAUTION: Some parts of this product can become very hot and cause burns. Particular attention has to be given where children
and vulnerable people are present.
NOTE: This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance
in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall
not be made by children without supervision.
2.
INTRODUCTION
Electric fan heater for industrial applications. Features two heat settings and adjustable thermostat control with fan only option. Auto
cooling system to prevent unit from overheating during use. Tilt function which enhances the distribution of heat. Robust and sturdy
frame with wheels to enables the user to transport it easily around the designated space. A totally dry heat with no condensation, no
gas, no fumes and no smell. Ideal for workshops and garages. Supply: 415V/3ph - 63A. Supplied with 3-phase chassis mounted
5-pin connector (extension cable required).
3.
SPECIFICATION
Model No.: ................................................. EH30001.V2
Heated Area: ........................................................ 600m³
Output: .....................................................102,500Btu/hr
Plug Type: ............................................ Red - 63A-4P+E
Power: ................................................... 15000/30000W
Supply: .................................................. 415V/3ph - 63A
IMPORTANT!
This unit is designed to raise the ambient temperature of an entire room, the temperature of the air coming out of the front of the
heater will be warmer than the general temperature of the room, but there may not be a significant increase owing to the large
volume of air passing over the element. For the same reason, the element is hot during operation, but does not glow. The room
temperature depends on room size, insulation and ambient temperature, which will increase as the room warms.
3.1.
ASSEMBLY OF THE WHEELS. (fig.2)
3.1.1.
Take the axle rod and insert it through the holes in the 'V' frames so that the threaded rod ends protrude equally either side. Retain
the axle rod in this position by inserting a split pin through the holes situated just on the inside of each leg frame.
3.1.2.
Slide a plain washer over each end of the axle rod, followed by a wheel then followed by another plain washer.
3.1.3.
Screw a nyloc nut onto each end of the axle by hand until it begins to bite. Hold one nut steady with a 19mm spanner and
progressively finger-tighten each nut until it bottoms out on the thread. Once the heater body is fitted between the legs tighten the nuts to
fix the wheels in position.
3.2.
ASSEMBLY OF THE LEGS TO BODY. (fig.1)
3.2.1.
Screw pivot bolt, lock washer and plain washer finger-tight into insert in body of heater via central hole in gusset at the top of legs.
3.2.2.
Screw thumbwheel into insert fitted to body via the slot in the gusset. Tighten all fixings once assembled.
3.2.3.
Note that the axle hole at the shorter end of the 'V' frames should be orientated towards the back of the heater.
3.3.
ASSEMBLY OF THE HANDLE. (fig.3)
3.3.1.
Slide a plain washer over each of the four M5 x 50mm bolts supplied.
3.3.2.
Lay the 'U' shaped handle frame onto the front face of the leg frames and align the two holes at each end of the handle frame with the two
holes in each leg frame. Insert two bolts at each joint as indicated in fig.3.
3.3.3.
Whilst continuing to support the handle frame slide a plain washer followed by a split washer onto the end of each protruding bolt
and retain them with a nut. Tighten all four nuts with an 8mm spanner.
fig.1
© Jack Sealey Limited
fig.2
Original Language Version
fig.3
EH30001.V2
Issue 2 (1,F)
07/11/23
Advertisement
