1. Manuals
  2. Brands
  3. AccesStyle Manuals
  4. Grinder
  5. AG-A/125-750/PCS
  6. User manual

AccesStyle AG-A/125-750/PCS User Manual

Electric hand tool
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
ELECTRIC HAND TOOL
ACCESSTYLE
ANGLE GRINDER
Model AG-A/125-750/PCS
USER MANUAL
Dear buyer! Thank you for purchasing an Accesstyle brand tool. All our products are manufactured to the
highest quality requirements.
We hope that our tool will fully meet your expectations.
For long life, efficient and safe operation, please read this manual carefully and keep it for future reference.
When purchasing a product:
- require checking its operability by trial closing, as well as completeness, according to the delivery set given
in this manual;
- make sure that the warranty card is properly executed, contains the date of sale, the stamp of the store
and the signature of the seller;
Attention! Power tools are hazardous equipment. To avoid electric shock, fire and/or serious injury you
need STRICTLY respect the warnings and instructions. Read all safety warnings and all instructions before
operating a power tool. Save all warnings and instructions for future reference

Advertisement

Table of Contents
loading

Summary of Contents for AccesStyle AG-A/125-750/PCS

  • Page 1 ANGLE GRINDER Model AG-A/125-750/PCS USER MANUAL Dear buyer! Thank you for purchasing an Accesstyle brand tool. All our products are manufactured to the highest quality requirements. We hope that our tool will fully meet your expectations. For long life, efficient and safe operation, please read this manual carefully and keep it for future reference.

  • Page 2: General Power Tool Safety Warnings

    General Power Tool Safety Warnings Work area safety Keep work area clean and well lit. Cluttered or dark areas invite accidents. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. Keep children and bystanders away while operating a power tool.
  • Page 3 Use clips, adjusting clamps, a vice clamps, or other method to securely hold the workpiece. Holding the part with your hand or body is not secure and could result in loss of control, tool breakage, or injury. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed Do not use the power tool if the switch does not turn it on and off.

  • Page 4: Kickback And Related Warnings

    the mounting hardware of the power tool will run out of balance, vibrate excessively and may cause loss of control. Do not use a damaged accessory! Before each use inspect the accessory such as cutting or abrasive wheels for chips and cracks, backing pad for cracks, tear or excess wear, wire brush for loose or cracked wires. Do not use battered accessory.

  • Page 5: Brief Description Of The Product

    during start-up. The operator can control torque reactions or kickback forces, if proper precautions are taken. Never place your hand near the rotating accessory. Accessory may kickback over your hand Do not position your body in the area where power tool will move if kickback occurs. Kickback will propel the tool in direction opposite to the wheel’s movement at the point of snagging.

  • Page 6: Application Area

    Disk protection Spindle lock Power button lock Rated power 750 W Network cable length Socket type VDE socket APPLICATION AREA Angle grinder is a hand tool equipped with an electric motor, designed for cutting, grinding, deburring and other mechanical work with products made of stone, metal and other hard materials. The axis of the motor and the fixed tool are located relative to each other at an angle of 90°.

  • Page 7: Power On/Off

    - Slide the disc over the inner flange mounted on the spindle. - Install back the clamping nut and screw it down. (Use side A or side B of clamping nut depending on tooling thickness) - Tighten the clamping nut to the stop using a special wrench. - Disengage the spindle lock button.

  • Page 8: Tool Maintenance

    As a result of using the tool, the tooling and the parts adjacent to it can become very hot - do not touch them until they are completely cool to avoid burns. When performing grinding and deburring operations, position the edge of the tooling at an angle of 150 to the surface to be worked.

  • Page 9: Service & Maintenance

    5. Warranty service is performed by organizations authorized for this - authorized service centers, the list of which is contained on the support page of the website http://www.accesstyle.ru and is available by phone 8-800-250-07-17. During the warranty period, the elimination of manufacturing defects is free of charge for the buyer upon presentation of the original completed warranty card and / or documents confirming the fact and date of purchase (cash receipt).

Table of Contents