Related Manuals for jcb JCB-SH140D
Summary of Contents for jcb JCB-SH140D
- Page 1 SPACE HEATER INSTRUCTION & USER MANUAL JCB-SH140D Original Instructions IM-DH140D-EN...
-
Page 2: Table Of Contents
Fuel Nozzles Fuel Filter Fuel Pressure Adjustment & Wiring Diagram Troubleshooting Specifications Warranty, Manual Updates, Returning Your Product, Leaving a Review & Ordering Spare Parts Contact Us Recycling & Disposal & Environmental Protection Declaration of Conformity JCB-SH140D Instruction & User Manual... -
Page 3: Introduction
The safety precautions and warnings are to ensure your safety and protect you from harm or damage to the product. The information contained in this manual was accurate at the time of production, however Genpower Ltd & JCB may make modifications to the product without notification. JCB-SH140D... -
Page 4: General Warnings & Disposal
This WILL cause server burns and injury. Diesel Fuelling Warning: ONLY fill this machines with diesel or suitable fuel. When fueling ensure the machine is OFF, away from an open flame or ignition source. JCB-SH140D Instruction & User Manual... -
Page 5: Safety Information
> Do not overreach. Keep proper footing and balance at all times. This enables better control of the machine in unexpected situations. Extending your body too far can result in a loss of balance and you may fall which will result in injury. JCB-SH140D Instruction & User Manual... -
Page 6: Inspect Your Machine
> Keep the machine in good operating condition. Operating the machine in poor or questionable condition could result in serious injury. > Be sure all safety devices are in working order and warning labels are in place. These items are installed for your safety. JCB-SH140D Instruction & User Manual... -
Page 7: Work Area & During Use
> Do not carry passengers. > Always turn off the machine and ensure that all moving parts have come to a complete stop before making any repairs, adjustments, or inspections. JCB-SH140D Instruction & User Manual... -
Page 8: Risk Of Burns/Fire/Explosion
All fuel storage should be in accordance with federal, state, or local authorities have jurisdiction. > NEVER use this heater in living or sleeping areas. > NEVER use this heater where flammable vapours may be present. JCB-SH140D Instruction & User Manual... -
Page 9: Electrical Safety
> All trailing cables should be routed so as not to cause any kind of trip hazard. > NEVER work on or near electricity with wet hands, wet clothing and wet gloves. JCB-SH140D Instruction & User Manual... -
Page 10: Carbon Monoxide
DO NOT enter a room you suspect of having carbon monoxide present – instead call the emergency services. Contact a Doctor immediately or go to Hospital – let them know that you suspect carbon monoxide poisoning. JCB-SH140D Instruction & User Manual... -
Page 11: Fuel Safety
> When fuel is spilled on yourself or your clothes, wash your skin and change clothes immediately. > ALWAYS clean up spills promptly using absorbent granules and a lidded bin. JCB-SH140D Instruction & User Manual... -
Page 12: Fuelling/De-Fuelling & Storage
(such as a water heater, furnace, or clothes dryer). Allow the engine to cool before storing in any enclosure. > Replace all fuel tank and container caps securely and wipe up spilled fuel. Never operate the unit without the fuel cap securely in place. JCB-SH140D Instruction & User Manual... -
Page 13: Batteries (Where Present)
Gasses from charging batteries are highly flammable and great care should be taken to charge in well ventilated areas. There is an explosion risk if the battery terminals are short circuited, when connecting/disconnecting ALWAYS exercise great care so that the terminals or battery JCB-SH140D Instruction & User Manual... -
Page 14: Vibrations (Where Applicable) & Noise (Where Applicable)
Limit the working time to a minimum. For your personal protection and protection of people working nearby it is also advisable for them to wear hearing protection. > See Certificate of Conformity section for Outdoor Noise declaration of conformity. JCB-SH140D Instruction & User Manual... -
Page 15: General Safety
1-K Kerosene, and care should be taken to provide more fresh air ventilation to accommodate any added contaminants that may be added to the heated space. Use of #1 or #2 fuel oil may result in more periodic maintenance. JCB-SH140D Instruction & User Manual... -
Page 16: Component List
COMPONENT LIST JCB-SH140D Instruction & User Manual... -
Page 17: Dimension List
Gauage showing the current Fuel Pressure 11. Flame Cone - An element that helps to disperse the outlet heat Dimensions A. 879mm F. 702mm B. 570mm G. 935mm C. 867mm H. 514mm D. 844mm I. 319mm E. 237mm JCB-SH140D Instruction & User Manual... -
Page 18: Unboxing Safety & Box Contents
>Wheels & Wheel Cover >Axle (This is housed within the anti-vibration packaging) >2 x Cotter Pins >Washers >Front Wheel Mounts > Rear Mounts >8 x Nuts (A) >4 x Nuts (B) JCB-SH140D Instruction & User Manual... -
Page 19: Assembly
6. Place a wheel, followed by a washer. Secure this into place using the Cotter Pins. Simply insert the cotter pin through the hole in the axle, until holds into place. 7. Repeat on both sides and secure the Wheel Covers JCB-SH140D Instruction & User Manual... -
Page 20: Operation
>NEVER use Diesel (1-K kerosene) that has been stored from one season to the next. It deteriorates over time. OLD DIESEL (1-K kerosene) WILL NOT BURN PROPERLY IN THIS HEATER. >Use diesel in the heater/ 1-K kerosene is a suitable substitute. JCB-SH140D Instruction & User Manual... -
Page 21: Operation Theory & Fuelling The Heater & Ventilation
Always provide a fresh air opening in the heated space of at least three square feet (2800sq.cm) for each 29kW/hr of heater output. The following are some examples.. -A two-car garage door raised 15.24cm (6 inches) -A single-car garage door raised 15.24cm (9 inches) JCB-SH140D Instruction & User Manual... -
Page 22: Starting & Stopping & Restarting
Simply turn the power switch to “OFF” position and unplug the power cord. Operation- Restarting Wait ten seconds after shutting off the heater. Turn the power switch to “ON” position. Be sure to follow all starting procedure precautions. JCB-SH140D Instruction & User Manual... -
Page 23: Maintenance And Care
>To drain the fuel tank, simply remove the Drain Plug bolt and washer >Allow the fuel to flow out. >Once all the fuel has been removed, Re- >install the Washer and Drain Plug. Drain Hole Washer Drain Plug JCB-SH140D Instruction & User Manual... -
Page 24: Photocell
>The photocell should be cleaned at least once per heating season or more depending on condition. >Use a cotton swab dipped in water or alcohol to clean the lens of the photocell. *NOTE: the proper photocell position as noted in the diagrams. Photo Lens Incorrect Position Circuit Board Correct Position JCB-SH140D Instruction & User Manual... -
Page 25: Ignition Electrode
>Remove the screw that secures the Ignition Electrode. Now Remove the Ignition Electrode >After removing the electrode, clean the terminals with a wire brush. >Re-gap the terminals to 0.14’’(3.5mm) if required. Screw Ignition Electrode Ignition Wires Spark Gap Burner Head JCB-SH140D Instruction & User Manual... -
Page 26: Air Filter & Fan Blades
Remove all accumulated dust and dirt with a damp cloth, taking care not to bend any of the fan blades. Be sure fan blades are dry before re-starting the heater. For fan removal, see below. Set Screw Motor Shaft Fan Blade JCB-SH140D Instruction & User Manual... -
Page 27: Fuel Nozzles
NOTE: Use of diesel (1-K kerosene) may require additional maintenance. Using this heater without proper maintenance or with contaminated or old fuel may lead to improper combustion and possible soot production. SUITABLE FUELS ARE ESSENTIAL. JCB-SH140D Instruction & User Manual... -
Page 28: Fuel Filter
>Replace/Clean Fuel Filter, then reattach the bottom Fuel Line first. Return back into it's position. >Reattach the top Fuel Line and replace Control Panel Cover Photocell Wire Circuit Board Fuel Filter Screw Fuel Line Circuit Panel Cover Power Switch Power Switch JCB-SH140D Instruction & User Manual... -
Page 29: Fuel Pressure Adjustment & Wiring Diagram
Correct pump pressure is 38Kpa / 5.5Psi For best measurement of pressure, test with full tank of fuel. Optimum pressure occurs when the nose cone is cherry red and there are no extending flames from the heater. Adjustment Screw Wiring Diagram JCB-SH140D Instruction & User Manual... -
Page 30: Troubleshooting
2. Check power cord and extension cord 4. Improper electrical connection between to insure of proper connection, test power temperature limit sensor and circuit board. supply. 3. Check/replace fuse. 4. Inspect all electrical connection (see wiring diagram). JCB-SH140D Instruction & User Manual... -
Page 31: Specifications
SH140D Heat Output (kW) Heat Output(BTU) 126,250 Fuel Consumption (L/hr) Fuel Tank Capacity (L) Kerosene/Diesel Fuel Type Heating Area(m 38/5.5 Pump Pressure (Kpa/Psi) Power Supplier 230V 50Hz 5A Phase Type Single 22.3 Net Weight (kg) JCB-SH140D Instruction & User Manual... -
Page 32: Warranty, Manual Updates, Returning Your Product, Leaving A Review & Ordering
We reserve the right to make any modifications without prior notice whenever necessary. Our latest manuals are also placed online. All our manuals can be downloaded at: www.jcb-tools.co.uk Returning Your Product If you are returning your product, please contact the dealer for their returns policy. -
Page 33: Contact Us
Our friendly aftersales team will be more than happy to help you. Phone Call our team on 01646 687 880 Email aftersales@genpower.co.uk Post Genpower Ltd, Isaac Way, Pembroke Dock, Pembrokeshire, SA72 4RW. Support Website Go to jcb-tools.co.uk JCB-SH140D Instruction & User Manual... -
Page 34: Recycling & Disposal & Environmental Protection
> You must comply with local regulations for the disposal of waste materials after mowing. > When disposing, do not pollute the environment with the machine, but hand it over to a disposal centre, in accordance with the local laws in force. JCB-SH140D Instruction & User Manual... -
Page 35: Declaration Of Conformity
The person authorized to compile this technical file: Date: 01/12/2022 Signature Name/ title: Roland.J.Llewelin / Managing Director JCB Tools are a Licensee of J.C.Bamford Excavators ltd, operated via Genpower ltd. Address: JCB Tools ,Isaac Way, Prembroke Dock, SA72 4RW JCB-SH140D Instruction & User Manual...