1. Manuals
  2. Brands
  3. InterTest Manuals
  4. Digital Photo Frame
  5. SeeUV WebViewer EM14838
  6. Operation & service manual

InterTest SeeUV WebViewer EM14838 Operation & Service Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
®
Free Standing
EM14838
Vertical Reach · Operation & Service Manual
To avoid injury, read and understand documentation for each system component
prior to operation. Direct any questions about operation to InterTest at
(908) 496-8008 or service@intertest.com
®
Original Instructions

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SeeUV WebViewer EM14838 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for InterTest SeeUV WebViewer EM14838

  • Page 1 ® Free Standing EM14838 Vertical Reach · Operation & Service Manual To avoid injury, read and understand documentation for each system component prior to operation. Direct any questions about operation to InterTest at (908) 496-8008 or service@intertest.com ® Original Instructions...

  • Page 2: Table Of Contents

    ELMO CCU ............Monitor Swing Arm........... Sony Monitor............USHIO UV-LED Light Source........35-watt LED White Light Source ......... 7" HDMI Monitor and Recorder ........InterTest, Inc • 303 Route 94 • Columbia, NJ 07832 REV 1, 4.03.19 908-496-8008 • service@intertest.com • www.intertest.com...

  • Page 3: 1.0 Introduction

    To minimize viewable shadows, InterTest uses high grade optics and micro compo-nents to position the field of vision axis adjacent to the projected illumination. *specifications can change without notice InterTest, Inc • 303 Route 94 • Columbia, NJ 07832 REV 1, 4.03.19 908-496-8008 • service@intertest.com • www.intertest.com...

  • Page 4: 2.0 Customer Support

    Customer Service team at: Address: InterTest, 303 Route 94 Columbia, NJ 07832 Email: service@intertest.com Phone: +1 908-496-8008 Toll free in USA - +1 800-535-3626 InterTest, Inc • 303 Route 94 • Columbia, NJ 07832 REV 1, 4.03.19 908-496-8008 • service@intertest.com • www.intertest.com...

  • Page 5: 3.0 Warranty

    The laws of the State of New Jersey shall govern this warranty. Note: In the event that the equipment can not be returned to InterTest, Inc., for whatever reason, the customer agrees to pay for all travel and living expenses incurred to have an InterTest, Inc.

  • Page 6: 4.0 Unpacking & Inspection

    J. STORAGE DRAWER K. WHITE LIGHT SOURCE L. UV LIGHT SOURCE M. POWER STRIP N. CART O. CASTER WHEEL WITH BRAKE Figure 1 InterTest, Inc • 303 Route 94 • Columbia, NJ 07832 908-496-8008 • service@intertest.com • www.intertest.com REV 1, 4.03.19...

  • Page 7: 5.0 Assembly

    Avoid potential pinch points at all times. Provide a generous bend radius (>50mm) for UV light guide cable. InterTest, Inc • 303 Route 94 • Columbia, NJ 07832 REV 1, 4.03.19 908-496-8008 • service@intertest.com • www.intertest.com...

  • Page 8: 6.0 Operation

    Figure 1 is an illustrated picture of the complete system as viewed by the operator. 8. Assure cart is positioned in proper alignment with target. Set caster wheel brakes (see Figure 1, "O") REV 1, 4.03.19 InterTest, Inc • 303 Route 94 • Columbia, NJ 07832 908-496-8008 • service@intertest.com • www.intertest.com...
  • Page 9 Figure 5 - Engage Pins 90° to engage counter clockwise 90° to disengage Figure 8 - Installation Figure 7 complete. Reverse order for removal InterTest, Inc • 303 Route 94 • Columbia, NJ 07832 REV 1, 4.03.19 908-496-8008 • service@intertest.com • www.intertest.com...
  • Page 10 Adjust the camera’s focus using the focus control found on the Control Box. Switch between the Normal and Mirrored views using the rocker switch on the Control Box. (refer to page 12 for more details.) REV 1, 4.03.19 InterTest, Inc • 303 Route 94 • Columbia, NJ 07832 908-496-8008 • service@intertest.com • www.intertest.com...
  • Page 11 * Option available for VIBES/WebViewer System = VIBES Cable connection for VIBES control option. † Motorized, Insertion and Elevation controls are added options. InterTest, Inc • 303 Route 94 • Columbia, NJ 07832 REV 1, 4.03.19 908-496-8008 • service@intertest.com • www.intertest.com...
  • Page 12 Part Rotation Encoder Cable Figure 11 Illustration not to scale and does not show cart. Specfications may be different than pictured above. REV 1, 4.03.19 InterTest, Inc • 303 Route 94 • Columbia, NJ 07832 908-496-8008 • service@intertest.com • www.intertest.com...
  • Page 13 Motorized movement of WebViewer® Boom along x-axis ELEVATION Motorized movement of WebViewer® Boom along y-axis *Only for manual horizontal and/or vertical positioning versions InterTest, Inc • 303 Route 94 • Columbia, NJ 07832 REV 1, 4.03.19 908-496-8008 • service@intertest.com • www.intertest.com...
  • Page 14 RADIAL REACH Inserts/retracts WebViewer® Camera head INSERTION Motorized movement of WebViewer® Boom along x-axis ELEVATION Motorized movement of WebViewer® Boom along y-axis InterTest, Inc • 303 Route 94 • Columbia, NJ 07832 REV 1, 4.03.19 908-496-8008 • service@intertest.com • www.intertest.com...
  • Page 15 The WebViewer is designed to inspect parts on an encoded, dual-rotating part fixture. InterTest, Inc. is not responsible for injuries or damages. Load the part on to fixture using best practices in line with customers own part handling policies and procedures. Exercise due caution at all times – use care to protect yourself, the part and the system.
  • Page 16 Toggles between transparent text background and black box background Toggles On-Screen Display into 4 SCREEN POSITION different screen quadrants Toggles between inches and UNITS centimeters REV 1, 4.03.19 InterTest, Inc • 303 Route 94 • Columbia, NJ 07832 908-496-8008 • service@intertest.com • www.intertest.com...

  • Page 17: 7.0 Care & Maintenance

    7.2 Symbol Reference Warning: Heat Operation & Service Source Manual Warning: Warning: Ultra- Moving Parts Violet Light Warning: Electrical Hazard InterTest, Inc • 303 Route 94 • Columbia, NJ 07832 REV 1, 4.03.19 908-496-8008 • service@intertest.com • www.intertest.com...

  • Page 18: 8.0 Safety

    Moving Components - The WebViewer contains moving parts. Please keep clear of all moving areas and components to prevent injury. REV 1, 4.03.19 InterTest, Inc • 303 Route 94 • Columbia, NJ 07832 908-496-8008 • service@intertest.com • www.intertest.com...
  • Page 19 Viewing Resolution: .05 mm (.002”) indication at a 25 mm (.98”) distance *Motorized Insertion and Elevation are optional InterTest, Inc • 303 Route 94 • Columbia, NJ 07832 REV 1, 4.03.19 908-496-8008 • service@intertest.com • www.intertest.com...
  • Page 20  Image Flip (to compensate while using the 90° AFT and 90° FWD optical adapters)  Zero resets for encoded position values InterTest, Inc • 303 Route 94 • Columbia, NJ 07832 REV 1, 4.03.19 908-496-8008 • service@intertest.com • www.intertest.com...
  • Page 21 105 route des pommiers Centre Ubidoca 74370 St Martin Bellevue FRANCE InterTest, Inc. declares under our sole responsibility that the product described Equipment Name: iShot See UV Free Standing WebViewer Model /Type: EM14838 Serial number(s): SO53569 Complies with the requirements of the following European Directives: Machinery Directive 2006/42/EC;...
  • Page 22 9.0 Specifications & Declarations of Conformance EU DECLARATION OF CONFORMITY Product ULB-35i, ULB-35p, ULB-35ndt, ULB-35rvi Manufacturer’s name Ushio America Inc. Oregon Operations Division Business Address Ushio America Inc. 5440 Cerritos Ave., Cypress, CA 90630 This declaration of Conformity is issued under the sole responsibility of the manufacturer. Object of declaration Model Number (not sensitive to spaces, dashes, suffix or case): ULB-35i, ULB-35p, ULB-35ndt, ULB-35rvi...
  • Page 24 9.0 Specifications & Declarations of Conformance Equipment Label InterTest, Inc • 303 Route 94 • Columbia, NJ 07832 REV 1, 4.03.19 908-496-8008 • service@intertest.com • www.intertest.com...
  • Page 25 10.0 Service Records Free Standing WebViewer on Cart EM14838 EM Number: SO57967 Serial Number: Date of Purchase: Date Service Performed InterTest, Inc • 303 Route 94 • Columbia, NJ 07832 REV 1, 4.03.19 908-496-8008 • service@intertest.com • www.intertest.com...
  • Page 26 MODEL Camera Control Unit CC431E Operation Manual Thank you for purchasing the ELMO camera control unit CC431E. To use the cam- era properly, carefully read this operation manual before use. After reading the manual, we suggest you keep it in a convenient place for quick reference. COMPONENTS (1) Camera control unit (CCU) (2) Accessory: Operation manual...
  • Page 27 SAFETY PRECAUTIONS Read the following safety precautions carefully before using this product. These instructions contain valuable information on safe and proper use that will prevent harm and damage to the operator and other persons. Make sure that you fully understand the following details (indications, graphic symbols) before proceeding to the remaining sections in this manual.
  • Page 28 • Do not put the product in an unstable, slanting and/or vibrated place. Drop and/or fail of the product may cause injury. • Do not touch the power cord or other connection cables during a thunderstorm. This might cause electric shock. Caution •...
  • Page 29 PART NAMES AND FUNCTIONS Camera Control Unit (CCU) POWER switch POWER switch AGC switch AGC switch POWER indicator WB switch POWER indicator WB switch CAMERA POWER AUTO UP button UP button MANU CAMERA CAMERA terminal FUNC terminal DOWN button DOWN button White balance White balance FUNC button...
  • Page 30 1 CAMERA terminal Connects to the camera head. 2 POWER switch Turns on and off the camera control unit. 3 POWER indicator Lights up when the power is turned on. 4 AGC switch Selects the gain mode. (AGC OFF/AGC ON/SENS UP) 5 WB switch Selects the white balance mode.
  • Page 31 CONNECTION Example of Standard Connection Monitor (Option) Camera control unit VIDEO Camera Lens head (Option) (Option) CAMERA DC IN 12V Camera cable (Option) DC 12V DC power supply (Option) Cautions on Connection • When connecting or disconnecting the camera cables (for the camera head and camera control unit), always turn off the power switch of the camera control unit first.
  • Page 32 Connection on CCU Back Panel The figure below shows the back panel connection terminals of the camera control unit. DC IN 12V EXT SYNC S-VIDEO VIDEO REMOTE IRIS FUNC LOCK Connector Pin Assignments DC IN 12V S-VIDEO REMOTE IRIS +12V +12V VIDEO +12V...
  • Page 33 • Using the auto-iris lens The following table shows the IRIS terminal when using the auto-iris (EE) lens. Table 1 IRIS Connector Signal Rated Terminal No. –– 0.8 ± 0.1Vp-p Video signal Power (DC) + 12V (less than 50mA) (GND) ––...
  • Page 34 HOW TO USE THE CAMERA Turn on the POWER switch on the camera control unit and adjust the lens iris and focus while observing a picture on the monitor screen. To obtain the best picture quality, per- form various settings. AGC (Automatic Gain Control) AGC functions “OFF”, “ON”...
  • Page 35 (1) White balance adjustment in modes other than AUTO (1.1) White balance adjustment in SET mode 1 Set the WB switch to “SET” position. 2 Shoot a white object to fill entire screen and press the UP button ( ) for about 2 sec.
  • Page 36 OPERATION OF SCREEN MENU Setting while monitoring the menu on the monitor screen is possible. Following seven items can be set. 1 Scene file 2 Electronic shutter (AUTO/MANUAL), backlight correction 3 Pedestal level 4 Phase matching in external synchronization (horizontal/subcarrier synchronization) 5 White balance, auto electronic shutter, AGC measurement area 6 White balance offset 7 Scene file factory setting...
  • Page 37 FILE (Screen File) FILE SHUTTER AUTO There are two scene files A and B which can be se- PEDESTAL lected according to the shooting state. SYNC AREA LINK:1 W B-OFFSET 1 Move the cursor to “FILE” in the main menu us- INIT.
  • Page 38 (1) Detail setting in AUTO mode (Auto Electronic Shutter) When the FUNC button is pressed after AUTO is se- AUTO lected, the submenu for SHUTTER:AUTO appears. FILE 1/60 Set details in this screen. SHUTTER 1/100 PEDESTAL 1/250 LEVEL: Adjust the auto electronic shutter SYNC 1/500 video level.
  • Page 39 PEDESTAL (Pedestal Level) FILE SHUTTER AUTO 1 Move the cursor to PEDESTAL using the UP or PEDESTAL DOWN button. SYNC AREA LINK:1 2 Press the FUNC button. The cursor moves to the W B-OFFSET data. Set the data using the UP or DOWN button. The data can be set in a range of –50 to +50.
  • Page 40 3 Move the cursor to a desired item (H-PHS, SC- PHS, SC-FINE) using the UP or DOWN button. FILE Press the FUNC button and the data is displayed. SHUTTER Set the data using the UP or DOWN button and PEDESTAL press the FUNC button to select the data.
  • Page 41 2 Press the FUNC button to display data 1 ~ SLIT for LINK. Move the cursor to a desired item of FILE AREA data (1, 1/2, 1/8, SLIT) using the UP or SHUTTER DOWN button. PEDESTAL SYNC 3 Press the FUNC button to set the data. AREA LINK 1 W B-OFFSET...
  • Page 42 WB-OFFSET (White Balance Offset) FILE SHUTTER AUTO This offsets the focusing point of white balance in PEDESTAL the direction of orange or cyan when the WB switch SYNC AREA LINK:1 is set to “SET”. W B-OFFSET INIT. 1 Move the cursor to WB-OFFSET using the UP or DOWN button.
  • Page 43 INIT. (Scene File Initialization) FILE SHUTTER AUTO This reset settings of the scene file to the factory PEDESTAL setting. SYNC AREA LINK:1 W B-OFFSET 1 Select a scene file (A or B) to initialize the setting INIT. in FILE. 2 Move the cursor to INIT. using the UP or DOWN button.
  • Page 44 EXTERNAL SYNC When using the camera with an external sync, connect a composite video signal (C-VIDEO) to the EXT SYNC terminal on back of the camera control unit. When the camera accepts external sync, it is automatically switched from the internal sync to the external sync. (1) External sync signal input conditions 0.3 ±...
  • Page 45 CAUTIONS ON USE AND INSTALLATION Carefully handle the units. Handling of the protection cap. Do not drop, or give a strong shock or vi- Keep the protection cap away from chil- bration to the camera. This may cause dren. Children may put them into mouth problems.
  • Page 46 TROUBLESHOOTING CHART Symptom Items to be checked No picture • Is the power supplied correctly? • Is the lens iris adjusted correctly? • Are the cables connected correctly? Poor color • Is the monitor (TV) adjusted correctly? • Is the white balance of the camera adjusted correctly? (in modes other than automatic trace) •...
  • Page 47 SPECIFICATIONS Specification with micro camera head (MN43H) connected. DC12V ± 0.5V Power supply Power consumption 310 mA Image sensor 1/2 inch IT-CCD Effective pixels Horizontal: 768 pixels, Vertical: 494 pixels Effective image area Horizontal: 6.54 mm, Vertical: 4.89 mm (1/2 inch type) Scanning system 2:1 interlace Scan frequency...
  • Page 48 PROFILE Unit : mm [inch] ø : diameter Camera Control Unit [6.14] [3.35] 11 [0.43] 7 [0.28] CAMERA POWER AUTO MANU FUNC 21.5 10.5 21.5 [0.85] [0.41] [0.85] [0.79] [1.06] [4.49] DC IN 12V EXT SYNC S-VIDEO VIDEO REMOTE IRIS FUNC LOCK 4-M3 pitch 0.5 Threaded hole...
  • Page 49 Servicing Instructions for Service Personnel Connection to Camera Head (MN42H/CN42H) When connecting to the camera head (MN42H/CN42H), select the internal switch inside the camera controller following to the procedures below. 1 After turning off the power, remove all the cables connected to the camera control- ler.
  • Page 50 6-14, Meizen-cho, Mizuho-ku, ELMO CO., LTD. Nagoya, 467-8567 Japan OVERSEAS SUBSIDIARY COMPANIES ELMO Canada Mfg. Corp. ELMO Mfg. Corp. ELMO (Europe) G.m.b.H. 44 West Drive, Brampton, Neanderstr. 18 1478 Old Country Road, Ontario, L6T 3T6, 40233 Düsseldorf, Plainview, NY 11803-5034 Canada Germany U.S.A.
  • Page 51 Model 7500 Floating Flat Panel Arm he award-winning 7500 Radial Arm is a remarkable work tool. Effortlessly position your monitor exactly where you want it, and add flexibility to your work style. Suspend your flat panel above the desk surface and reclaim your valuable space. Innovative cable management routes cables inside the arm, in order to keep your desk organized.
  • Page 52 Model 7500 Specifications 3. 1 25" 7.69" horizontal vertical range range 27" 17.90" 15.25" 8.88" 6.18" -.13" 4.5" 17.25" SIDE VIEW TOP VIEW TOP VIEW Vertical Range Horizontal Range Arm Folded CAPABILITIES FLEXMOUNT CONFIGURATIONS ™ Vertical range ..............18" (+/- 9" from horizontal) Horizontal range .............27"...
  • Page 53 InterTest, Inc • 303 Route 94 • Columbia, NJ 07832 • 908-496-8008 • sales@intertest.com • www.intertest.com...
  • Page 54 InterTest, Inc • 303 Route 94 • Columbia, NJ 07832 • 908-496-8008 • sales@intertest.com • www.intertest.com...
  • Page 55 InterTest, Inc • 303 Route 94 • Columbia, NJ 07832 • 908-496-8008 • sales@intertest.com • www.intertest.com...
  • Page 56 InterTest, Inc • 303 Route 94 • Columbia, NJ 07832 • 908-496-8008 • sales@intertest.com • www.intertest.com...
  • Page 57 UV-LED Light Source Kit...
  • Page 58 Agency Compliance Statements ..............11 FCC Class A Compliance Statement ............11 FCC Class A Compliance Statement ............11 Canadian Notice ..................11 Canadian Notice ..................11 iShot® UV/White LED Light Source Kit www.intertest.com Midori™ ULB-35_RVI Midori™ ULB-35_RVI www.ushio.com www.ushio.com...

  • Page 59: System Symbol Descriptions

    Prepare this product for reuse or separate collection as specified by Directive 2002/96/EC of the European Parliament and the Council of the European Union on Waste Electronic and Electrical Equipment (WEEE). If this product is contaminated, this directive does not apply. www.intertest.com Operating Manual Operating Manual www.ushio.com...

  • Page 60: Warning And Precautions

    Protection provided by the equipment maybe impaired if not used in AVERTISSEMENT accordance with the manufacture recommendations. / La protection assurée par l’équipement risque d’être altérée si l’appareil n’est pas utilisé conformément aux recommandations du fabricant. Midori™ ULB-35_RVI www.ushio.com iShot® UV/White LED Light Source Kit www.intertest.com...
  • Page 61 Figure 3. Front View ON/OFF Indicator ON/OFF Indicator ON/OFF Indicator Power ON/OFF Power ON/OFF Power ON/OFF Rotate Knob Rotate Knob Rotate Knob Light Intensity Light Intensity Light Intensity Knob Knob Knob Operating Manual Operating Manual Operating Manual www.ushio.com www.ushio.com www.ushio.com www.intertest.com Operating Manual...
  • Page 62 1/4-20 UNC mounting stud located in the middle of box bottom side. 1/4-20 UNC mounting stud located in the middle of box bottom side. Threaded Threaded Mounting Stud: Mounting Stud: 1/4-20 UNC 1/4-20 UNC Midori™ ULB-35_RVI Midori™ ULB-35_RVI www.ushio.com www.ushio.com iShot® UV/White LED Light Source Kit www.intertest.com...

  • Page 63: Maintenance And Cleaning

    Rotate knob to increase light output intensity to desired output. Repair For repair information, please contact Customer Service at: Repair Telephone: (714) 236-8600 Email: customerservice@ushio.com For repair information, please contact our team at: Phone: Office: 908-496-8008 Email: support@intertest.com Operating Manual www.ushio.com www.intertest.com Operating Manual...

  • Page 64: Manufacture Contact Information

    5.0 amp current equivalent with a minimum 5.0 amp current equivalent with a minimum 5.0 amp current limit rating. limit rating. limit rating. Midori™ ULB-35_RVI www.ushio.com Midori™ ULB-35_RVI Midori™ ULB-35_RVI Midori™ ULB-35_RVI www.ushio.com www.ushio.com www.ushio.com iShot® UV/White LED Light Source Kit www.intertest.com...

  • Page 65: Dimensions

    12vdc LiP Battery Pack 5002493 5002493 50159 Storz Fiber Adapter; screw-in 50159 50160 Olympus Fiber Adapter; screw-in 50160 Operating Manual Operating Manual www.ushio.com www.ushio.com UAC-01 Portable Light Case 5002496 www.intertest.com Operating Manual UPS-03 12vdc LiP Battery Pack 5002493 Operating Manual www.ushio.com...

  • Page 66: Approvals

    USHIO America or an authorized agent. The purchase date determines limited warranty requirements. No other express or implied limited warranty is given. Midori™ ULB-35_RVI www.ushio.com iShot® UV/White LED Light Source Kit www.intertest.com...

  • Page 67: Agency Compliance Statements

    Le present appareil numerique n’emet pas de bruits radioelectriques depassant les limites applicables aux appareils numeriques de la classe A prescrites dans le Reglement sur le brouillage radioelectrique edicte par le ministere des Communications du Canada. Operating Manual www.ushio.com www.intertest.com Operating Manual...
  • Page 68 Sold By: www.intertest.com 303 State Route 94 Columbia, NJ 07832 USA Office: 908-496-8008 Toll Free (U.S.): 800-535-3626 Fax: 908-496-8004 MADE IN USA Rev1-092017...
  • Page 69 ULB-35 SERIES LED LIGHT SOURCE OPERATING MANUAL...
  • Page 70 Preface Thank you for purchasing the Midori™ fiber optic illuminator which utilizes state-of- the-art solid-state illumination technology. The light source is a high output, efficient, compact and lightweight fiber optic light source for industrial applications where space is a premium. The ULB-35 series fiber illuminators utilize eco-friendly solid state LED lighting technology, exhibits instant-on and electronic intensity dimming capability with long operating lifetime.

  • Page 71: System Symbol Descriptions

    System Symbol Descriptions Caution: Consult Caution: Hot Surface accompanying documentation Caution Hazard Warning Lamp On Lamp Off Light; Lighting; Bright Light Illumination Intensity +49°C Storage Humidity Transport Temperature -20°C Alternating Current Direct Current Do Not Immerse in Any Manufacturer Liquid Do not dispose of this product as unsorted municipal waste.

  • Page 72: Warning And Precautions

    Warning and Precautions / Mises en garde et précautions WARNING / There are no user serviceable or replacement parts. Do not attempt to dismantle MISE EN GARDE box or remove top cover. / Aucune pièce ne peut être réparée ou remplacée par l’utilisateur.
  • Page 73 System Description and Operation The light source power switch should be in the OFF position. Plug the external 12vdc power supply into the 12vdc connector. Figure 1. Plug the external power supply cord into AC receptacle main power. Plug the fiber-optic bundle into the light port and connect the opposite end to the equipment being used.
  • Page 74 Figure 4. Cooling and Air Flow Paths Do not obstruct air flow paths. This device is designed to have proper forced air cooling paths to maintain thermal stable operation. Place in an area that provides adequate ventilation to prevent unit from overheating.

  • Page 75: Maintenance And Cleaning

    Maintenance and Cleaning Turn the LED Light Source off and unplug the power cord from both the wall outlet and the rear of the unit. Wipe the external surfaces clean with a cloth dampened with mild soap and water. DO NOT IMMERSE. Wipe the power cords clean with a cloth dampened with mild soap and water.

  • Page 76: Manufacture Contact Information

    Manufacture Contact Information Supplier Name: Ushio America, Inc. Address: 5440 Cerritos Ave. Cypress, CA 90630 Telephone: 714-236-8600 Email customerservice@ushio.com Website: www.ushio.com Model or Type: ULB-35 Environment Ratings Operating Temperature: 41° F to 104° F (5° C to 40° C) Humidity: 0 to 95% rh (non-condensing) Storage Temperature: -10°...

  • Page 77: Dimensions

    Dimensions Length: 127MM (5.0”) Width: 90MM (3.5”) Height: 68MM (2.7”) Weight: 0.45 kg (1.0 lbs) [90 mm] [ 127 mm ] 3.5” 5.0” [ 114 mm ] 4.5” [ 68 mm] 2.7” Illumination Source Type: LED Custom Module Color Temperature: 5700 K - 6500 K Nominal Power: 35 Watts...

  • Page 78: Approvals

    Approvals The CE mark on this product indicates that it has been tested to and conforms to the provisions noted within the following directives: Low Voltage: 2014/35/EU EMC: 2014/30/EU RoHS 2: 2011/65/EU In accordance with the following standards: EN61010-1 IEC 61326-1 EN 61326-1 IEC 62471 IEC/EN 61000 3-2...

  • Page 79: Agency Compliance Statements

    Agency Compliance Statements This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
  • Page 80 Release Version 1.8 Versatile IP Test Monitor 7 inch wide touch screen Video Surveillance Products (Installation and management) This product is for CCTV system installation and management. Some problems may occur with inappropriate use. Please read the instructions prior to its use and keep it with the warranty certificate.
  • Page 81 Cautions for use of this product If you give excessive shock to this product or drop it, LCD may be damaged. Therefore, have a special care not to break it. (The damaged LCD is not available for free A/S even in warranty.) Do not spray water directly and wipe this product gently with a dry towel when you clean it.
  • Page 82 Cautions for use of the memory card Checklist for the memory card selection Micro SD/SDHC/SDXC memory cards are compatible with this test monitor. Compatibility between memory cards and this test monitor depends on the brand and type of memory cards. Memory cards from the following brands are recommended for use with this test monitor.
  • Page 83 Cautions for use of the memory card Removal of the memory card Errors may occur in the saved file if you remove the memory card during use. Please refer to the following instructions to remove the memory card. Main Home Enter My Apps page from the Home screen.
  • Page 84 Cautions for use of the memory card Storage Screen Check if the Unmount SD card is enabled in the storage page. Recheck the inserted SD card status if the Unmount SD card is disabled even though the SD card is inserted. Please remove the SD card and insert it again. Unmount Screen Select OK when a message for unmounting the SD card is shown on the screen.
  • Page 85 Overview Table of Contents Cautions for use of this product Cautions for use of the memory card Overview Table of contents Introduction & Features IP App. functions Viewer App. functions Product components Product Parts and Descriptions Top interface Front interface Bottom Navigation and Tool Bar Backside interface &...

  • Page 86: Overview 3

    Overview Table of Contents Viewer App. Functions Main page Supported resolution SDI / HDMI / HD Analog Signal level meter function Focus meter function & CRC error count function Video menu bar RS-485 Tx. RS-485 Rx. & Analyze function Video recording Video capturing &...
  • Page 87 Overview Introduction This IP test monitor is a multifunctional test monitor based on Android system for convenient monitoring and maintenance for video surveillance systems. As this tester supports ONVIF, the international standard for IP security products, it is possible to connect with various network cameras easily and check their video.
  • Page 88 Overview IP App. functions IP Camera search Discover the IP address of your network camera connected to this test monitor or all network cameras on your LAN by Auto Discovery function. Live video checking Real-time video monitoring of your connected IP camera. IP camera settings IP camera video preview and IP camera address setting change available when building IP systems.
  • Page 89 Overview Viewer App. functions HD/EX/3G-SDI Input Support HD/EX/3G-SDI Input. Please refer to page 59 for more information on the supported resolution. HD Analog, CVBS Input Support AHD/TVI/CVI Input. Please refer to page 59 for more information on the supported resolution. HDMI Input &...

  • Page 90: Product Components

    Overview Product Components Please check if the following components are all included in your package when you receive this item. Item Name Description IP Multifunctional Charge the battery prior to its use. It may be discharged at Test Monitor the time of delivery. Exclusive bag Keep the test monitor in this bag for its storage or use.

  • Page 91: Product Parts And Descriptions

    Product Parts and Descriptions Top Interface Name Description The exclusive adapter included in this package is only allowed to recharge this test monitor. DC12V power supply for camera operation is also available ① Power Connector through this port by using the power output lead. There are 5,680 mAH Li- Polymer batteries built in this monitor.

  • Page 92: Front Interface

    Product Parts and Descriptions Front Interface Name Description IPS 7 inch TFT LCD panel in 1280x800 high resolution with tempered glass is applied. In addition, optical bonding is applied for outdoor environment and ① Touch Screen the fingerprint can be removed easily by applying the anti-fingerprint coating to this test monitor.

  • Page 93: Bottom Navigation And Tool Bar

    Product Parts and Descriptions Bottom Navigation and Tool Bar Name Description This button is for terminating an App. during operation or returning to the ① Back button previous page. This button is for going to the Home screen. However, in this case, the App. ②...
  • Page 94 Product Parts and Descriptions Backside Interface Name Description Test monitor stand for convenient monitoring. Adjust the angle of this test ① Monitor Stand monitor. ② Speaker Dual speakers are mounted. Adjust volume. Connection Diagram HDMI Output HD Analog & HD/EX-SDI CVBS Camera Camera Exclusive Adapter...

  • Page 95: Launcher

    Product Functions Launcher The following launcher screen will be shown once this test monitor is turned on. Name Description ① IP Camera App. This App. is for IP video. Tap the icon to open the IP App. This App. is for HD/EX/3G-SDI Video. Tap the icon to open the SDI Viewer ②...

  • Page 96: Ip App. Functions

    IP App. Functions IP Camera Connection and Settings Launcher page Select IP Camera App. to connect a network camera. IP App. Home page The IP Camera App. has various functions such as IP search, camera settings, monitor settings, ping test, gallery, etc. If you connect an IP camera by LAN directly, please go to page 18.

  • Page 97: Ip Camera Connection By Lan

    IP App. Functions IP Camera Connection by LAN This is for connecting an IP camera to the monitor by LAN directly without a DHCP server or a router. Change the monitor IP address to connect an IP camera. 1) When an IP camera is set with the DHCP or default IP address Monitor IP Settings Page Tap the Monitor Settings icon in the IP App.
  • Page 98 IP App. Functions 2) When connecting an IP camera manually (When you know the camera IP address) Monitor IP Settings Page Tap the Monitor Settings icon in the IP App. main page to see the above page. 'Use Ethernet' on the top of this page shall be marked all the time. Select 'Advanced Configure' at the bottom of this page to open the monitor IP setting page.

  • Page 99: Ip Camera Connection By A Dhcp Server

    IP App. Functions IP Camera Connection by a DHCP server This is for connecting an IP camera to the monitor when a DHCP server or a router is connected and it assigns an IP address to the camera and monitor automatically. Monitor IP Settings Page Tap the Monitor Settings icon in the IP App.

  • Page 100: Checking Items Prior To The Camera Discovery And Connection

    IP App. Functions Checking items prior to the camera discovery and connection Check the following items and move to the next step after completing the monitor settings. IP App. Home Page (Main Page) STEP 1 : Check the PoE status in the upper left corner. Turn on the PoE to supply PoE to your camera. If PoE is off, this monitor will not supply PoE to your camera.

  • Page 101: Ip Device Discovery

    IP App. Functions IP Device Discovery Camera #1 Camera #2 Camera #3 Camera #4 Search page Once you enter the Search from the IP App. main page, the discovered cameras will be displayed on the screen as shown in the above picture. IP values depend on camera brand due to the different network settings of camera manufacturers.

  • Page 102: Ip Camera Connection And Settings

    IP App. Functions IP Camera Connection and Settings Camera settings page Once you select the Camera Settings icon or one of discovered cameras in the Search page, the camera setting screen is displayed. Enter any word such as the camera name or installed location to identify the camera in the Name field.
  • Page 103 IP App. Functions Once the camera is connected, the preview video will be displayed as shown in the following picture. Camera Setting Page Scroll-down the left setup panel after the camera is connected. you can modify the profile settings. After completing all settings, press the Save button to save the configuration to the IP App. main page for future use if you choose so.

  • Page 104: Utilize Configuration

    IP App. Functions Utilize Configuration Configuration Menu Screen In the IP App. main page, press and hold the saved configuration or press the SET key to display a context menu. Select Edit to change the configuration and select Explore to check the information of the configured camera.

  • Page 105: Ip App. Main Page

    IP App. Functions IP App. Main Page Name Description There are Search, IP camera settings, Monitor settings, Ping test, Gallery ① Action Menu Icon icons as shown in the above picture. This is for turning on/off the PoE (Power over Ethernet) function. When the PoE function is on, this monitor supplies PoE to a connected IP camera ②...
  • Page 106 IP App. Functions Menu in the IP App. Main Page In the IP App. main page, once you press the menu or mode key or touch menu icon , the menu bar will be shown as follows. PoE OFF PoE function is OFF. PoE ON PoE OFF When turning the PoE function on, PoE 48V OUT will be shown on...

  • Page 107: Ip Device Search

    IP App. Functions IP Device Search Tap the search icon to start camera discovery as shown below. All IP cameras will be searched automatically when entering this screen. Name Description ① Refresh Touch this button to try the search again. This is a method to search IP devices by using Ping and available for use after ②...

  • Page 108: Camera Settings

    IP App. Functions Camera Settings Tap the Camera Settings icon in the IP App. main page to test an IP camera. Selecting one of the discovered camera in the Search page also opens Camera Settings as following. Name Description ① Device Type Select your device type such as ONVIF, RTSP and MJPEG.

  • Page 109: Camera Network Settings

    IP App. Functions Camera Network Settings This function is available only when the camera is connected. Tap the Network Setting icon to enter the following page. Camera Network Information MAC Address is fixed for each camera. Interface Type represents the current network type of the connected camera.

  • Page 110: Edit Media Profile

    IP App. Functions Edit Media Profile Once a camera is connected, you can edit the media profile. Tap the profile edit icon to see the following image. Name Description You can set its resolution, encoding type, video quality through video ①...
  • Page 111 IP App. Functions Main page If tapping the at the top right of the screen after a camera is connected, the window will be shown as the following image. Name Description The PoE voltage status sign on the top will move to the left bottom in video full screen mode.

  • Page 112: Live Video Menu Bar

    IP App. Functions Live video menu bar In the IP App. video page, you tap the menu or mode key or touch the menu icon to show the following menu bar. Full Image / Full Screen In the full image mode, the full video is displayed. This may result in empty spaces that are not occupied by the video.

  • Page 113: Video Recording

    IP App. Functions Video Recording Recording Start Button Start recording by tapping button. Recording Status Display The recording time is displayed. The recording is available up to 5 minutes. Recording End Button End recording and save the recorded file by tapping button.

  • Page 114: Snapshot Capturing

    IP App. Functions Snapshot Capturing Capturing Start Button Start capturing by tapping button. Capturing Status Display Display the capturing status. Capturing Function Termination Select the Capturing in the menu bar. Then, the “√” mark will be removed and the capturing function will be terminated. Press the BACK key to terminate the capturing function.
  • Page 115 IP App. Functions Audio Input This monitor supports AAC (Advanced Audio Coding), G.711 μ-Law, G.711 A-law codecs. If the camera supports audio, the sound will come out through the monitor's speaker. Please note that a profile may not include audio even when the camera supports audio. You can control the speaker output by using the mute function.

  • Page 116: Pan/Tilt Functions

    IP App. Functions Pan/Tilt Functions Opto-mechanical pan/tilt functions are available for PTZ cameras only Pan/tilt the camera by touching the screen and wiping it. Pan/tilt functions are available by both touching the screen and using the arrow keys. The pan/tilt speed depends on each camera brand when operating by the arrow keys. Swipe left from right Swipe up from down Swipe diagonally...

  • Page 117: Zoom Function

    IP App. Functions Zoom Function If the camera supports opto-mechanical PTZ, enable the Digital PTZ first to use Digital Zoom function. Otherwise, opto-mechanical Zoom will be applied. Zoom out/in the video screen by your fingers. Pinch two or more fingers together to zoom out. Stretch two or more fingers apart to zoom in.
  • Page 118 IP App. Functions Presets This function is enabled only for cameras supporting presets. Some characters may not be allowed in preset names by some camera brands. Presets function shows a list of defined presets. Type the Preset Name and press the + button to add a preset.

  • Page 119: Configuration Storage

    IP App. Functions Configuration Storage You can save the configuration after entering all camera information required and previewing the video. Once you save the configuration, you can easily start its corresponding video from the IP App. main page. All camera settings are saved. When changing the camera settings, please save the configuration again. Stored Information All setting information to set a camera such as Name, IP Address, ID and Password is saved.

  • Page 120: Camera Configuration Context Menu

    IP App. Functions Camera Configuration Context Menu Press and hold a saved configuration or Set key. A menu will be shown as the following picture. Some functions are not available for RTSP, MJPEG configurations, which are not ONVIF. Name Description ①...

  • Page 121: Monitor Ip Settings

    IP App. Functions Monitor IP Settings Tap the Monitor Settings icon in the main page of the IP App. to open the Monitor Network Settings page. Tap Advanced Configure at the bottom of the screen to display the following image. Name Description If you check DHCP, a DHCP server can assign IP to this test monitor.
  • Page 122 IP App. Functions IP Address Selection IP address classes shall match each other. The range of the numbers available for IP address is from 0 to 255. All IP address classes can be identified with the bit of the first number. With other classes, it cannot communicate with each other. Class A: 1.0.0.1 ~ 127.255.255.254 Class B: 128.0.0.1 ~ 191.255.255.254 Class C: 192.0.0.1 ~ 223.255.255.254...

  • Page 123: Ping Test

    IP App. Functions Ping Test You can check the connection status of the camera by Ping test. For Ping test, the camera's IP address is used only. Name Description ① IP Address Enter the camera IP address for the Ping test. ②...

  • Page 124: Main Page

    Viewer App. Functions Main Page Viewer App. means an App. for SDI, HDMI, AHD, CVI, TVI, CVBS. Wi-Fi should be off for SDI input. It may generate some video noise in a long-distance transmission. SDI products should be connected to SDI Input BNC port and HD analog/CVBS products shall be connected to Video Input BNC port for the relevant video signal input.

  • Page 125: Supported Resolution

    Viewer App. Functions Supported Resolution When entering video, the signal format and resolution are displayed. Select 3G in the input mode for 3G-SDI video input. The Video Input Status window will be closed in 10 seconds after video is entered. HD-SDI Supported Resolution 720p 25/30/50/60 Hz Input 1080i 50/60 Hz Input...

  • Page 126: Signal Level Meter Function

    Viewer App. Functions Signal Level Meter function 1. SDI Level Meter SDI Level Meter represents the current SDI signal status signal size) in percentage. 100% means the most optimum signal status (the biggest signal size) and the lowest value is 0%. No Good NG displayed in 0~29% Severe signal attenuation...
  • Page 127 Viewer App. Functions Focus Meter function Focus Meter represents the optimum and current focus status(depth) in numerical values The focus depth is represented in numerical values between 255 and 0. Adjust the optimum and current focus depth to be matched. This value depends on camera or lens types.

  • Page 128: Video Menu Bar

    Viewer App. Functions Video Menu Bar Available menu in this bar depends on video signal mode. Press the Menu, Mode button or Menu icon , the Menu bar will be popped up as shown as follows. PTZ Capacity or OSD settings are available through RS-485. It is possible to receive or analyze data by using RS-485.

  • Page 129: Ptz

    Viewer App. Functions To implement PTZ function, the Mode, Protocol, Address and Baudrate must be set. For RS-485, match the polarity for cable connection. UTC function is activated in HD Analog and CVBS modes and by this function, camera control via coaxial cable is available.
  • Page 130 Viewer App. Functions RS-485 Tx The current settings are displayed on the top of the screen. Control the directions by arrow keys, referring to the instructions at the bottom of the screen. Name Description ① Setting Status All setting values such as mode, protocol, address, baudrate are displayed. In PTZ mode, you can select and change Pan/Tilt and Zoom/Focus by touch ②...

  • Page 131: Rx. & Analyze Function Utc

    Viewer App. Functions RS-485 Rx The current settings are displayed on the top of the screen. Data transmitted through RS-485 cable is displayed in HEX value on the screen. When the data is more than 264 Byte, the previous data will be deleted. Analyze function RS-485 commands received from CCTV controller or external devices are displayed.
  • Page 132 Viewer App. Functions UTC is available in HD Analog and CVBS modes. Camera PTZ or OSD settings are available over coaxial cable without any separate data lines. Name Protocol Supported Items Hanwha (Samsung) Techwin (Winner5), Pelco, ① CVBS Mode Pelco - C D-Max (PIXIM) ②...

  • Page 133: Video Recording

    Viewer App. Functions Video Recording It is not recommended to record for a long time without any memory card. Mount Micro SD card if the internal storage capacity is not sufficient. You can set the storage location in Settings after mounting Micro SD Card. When recording video, it is saved in MP4 format.
  • Page 134 Viewer App. Functions Video Capturing It is available to capture and save images in JPG format. Mount Micro SD card if the internal storage capacity is not sufficient. You can set the storage location in Settings after mounting Micro SD Card. How to use Gallery The recorded or captured images are saved in Gallery.

  • Page 135: Poc Function

    Viewer App. Functions PoC function Supply power to the camera over coaxial cable. PoC function is activated in SDI mode and available for PoC cameras only. PoC function is optional. Name Description The step before operating PoC. One you select “Yes”, it starts trying to ①...

  • Page 136: User Settings

    Viewer App. Functions User Settings This menu is to set the storage location, or turn on/off the Level/Focus meter functions. Storage Folder Set where to save the recorded or captured images. Activated only when Micro SD Card is mounted. Level/Focus Meter Turn on/off the Level/Focus meter functions.
  • Page 137 Appendix App. Update Use update App. to update Launcher, Viewer and IP App. Available during WI-FI only. Enter My Apps to update App. Check updates Check the currently installed version during WI-FI. Not activated when the currently installed App. is the newest version. Start updating Activated when the currently installed App.

  • Page 138: Specifications

    Appendix Specifications Model IP Test Monitor Display Resolution 1280 X 3 (RGB) X 800 Size 7.0 inch (Diagonal) Pixel Pitch 0.117(H) X 0.117 (V) mm Brightness 400 cd/m² Viewing Angle 89deg (Horizontal) / 89deg (Vertical) Total: 178deg (IPS Panel) Response Time 11ms HD-SDI 1.485Gbps...
  • Page 139 Appendix Specifications Model IP Test Monitor SDI LEVEL 0 ~ 100 % ERROR RATE ± 2% Measurement FOCUS LEVEL 0 ~ 255 FOCUS LEVEL 0 ~ 255 INPUT DC 12.6V (Exclusive Adapter) Power DC JACK 12V / 500mA OUTPUT USB 5V HDMI Input / Output HDMI C Type F HD-SDI Input...

  • Page 140: Faq

    Appendix Symptom Checking Method Reboot this test monitor. Check the connected cable status. Video may not be displayed, depending on the damage or length of the cable. Check the connected camera status. Viewer Check the termination resistor status. The signal size depends on the termination resistor settings.
  • Page 141 Appendix Symptom Checking Method When a camera uses any separate RTSP port, it may not be connected. For camera settings, please overwrite and change the RTSP port. - The default RTSP port is 554. It may depend on each camera brand. Video is NOT displayed If you initialize a camera after saving its configuration, it may not be able to connect the camera via the saved configuration.

  • Page 142: Extra Features

    Appendix Extra Features Security (Lock) mode Lock mode setting Lock for prevention of robbery Initialization is not available if you do not remember password or pattern once you lock it. Miracast mode Miracast Search products currently available for Miracast by entering Display < Wireless Display <...

  • Page 143: Warranty Certificate

    Appendix Warranty Certificate Model No. Serial No. Distributor Date you purchased Place you purchased Warranty Period Two (2) years from the date of purchase Name Purchaser Address This product has passed thorough quality control and test, and if this gets broken during normal use, we provide the two-year warranty service.

Table of Contents