Summary of Contents for EAGOTECH EDX
- Page 1 Product Manual This manual is intended primarily for the trained technician to install, disassemble, or maintain the e-bike. - 1 -...
-
Page 2: Table Of Contents
CONTENT PRODUCT FEATURES ....................- 3 - ........................- 3 - RODUCT ESCRIPTION ........................- 3 - ARTS ESCRIPTION ........................- 4 - RODUCT IMENSION ..........................- 6 - EFINITION TECHNICAL DATA......................7 UNCTION ................................HARACTERISTIC ............................... OUNTING ARAMETER ........................... MOUNTING ........................ -
Page 3: Product Features
PRODUCT FEATURES PRODUCT DESCRIPTION is an 250W E-Bike electric system including battery and controller, it is compatible with most of down tubes for slim outlook e- bike. offers various options of HMI and sensors and supply sufficient power for wide range of light selections. -
Page 4: Product Dimension
PRODUCT DIMENSION a. Main dimensions... - Page 5 b. Cable and length...
-
Page 6: Pin Definition
PIN DEFINITION Motor Torque sensor Light H.M.I CEXLPERT E-BIKE SYSTEM... -
Page 7: Technical Data
Charge voltage 42.0V Charge current ≤ 4A Weight 1.50± 0.1 kg Waterproof level IPX6 CHARACTERISTIC Protocol Eagotech CAN Communication Operating temperature Charge:0~45℃/Discharge:-10~60℃ Storage temperature -20℃~+60℃(<1 month) -20℃~+45℃(<3 month) -20℃~+23℃(<12 month) Charging time approx. Standard charge:4hours Light power Total 15W/12V for head/rear lights... -
Page 8: Mounting
MOUNTING TOOL LIST Phillips screwdriver Cable lead wire ACCESSORY LIST Plastic gasket Optional depends on the frame type 3 pcs Phillips screw M5x0.8P (length depends on frame thickness) 3 pcs Charging socket with cable 1 pcs Countersunk M3x0.5P (length depends on frame thickness) 4 pcs Phillips screw MOUNTING INSTRUCTIONS... - Page 9 Step 2: Pull out the component cables and fasten the fixation screws (with maximum torque 30kgf-cm). Charging Socket Installation Step 1: Insert the charging port adapter. Make sure the dustproof plug end toward the seat tube.
- Page 10 Step 2: Fasten 4 pcs of screws. Step 3: Connect the battery and charging socket connectors.
-
Page 11: Operation
• All Eagotech Chargers only use genuine Eagotech batteries and battery packs, or battery packs approved for use with your e-bike by the manufacturer, and purchase only from reliable sources. -
Page 12: Charging Instructions
• Do not apply excessive tension to the cables and charging plugs. • Do not touch the metallic parts of the device or the power plug on the AC adapter or other parts when the charger is wet, electric shocks may occur. - Page 13 • Do not leave batteries in the charger for more than 24 hours, if the charging cannot complete in 24 hours, contact your local bicycle dealer for assistance. The battery pack can be charged under any power mode; interrupting the charging process will not damage the battery pack.
-
Page 14: Safety Instructions
• Do not put fingers or hands into the product. • Do not use this product if the flexible power cord or output cable is frayed, has broken insulation, or any other signs of damage. • All the component leads shall use original Eagotech components. -
Page 15: Important Notice
• The term “battery” is used in these instructions to mean all original Eagotech e-bike batteries. • Read and observe the safety warnings and directions contained in all the Eagotech e-bike system operating instructions and in the operating instructions of your e-bike. GROUNDING INSTRUCTIONS •... -
Page 16: Moving And Storage Instructions
MOVING AND STORAGE INSTRUCTIONS • When possible, keep the product and all e-system components in their original package and keep tools or other metal objects away from them while storage and moving. • If you did not keep the original packaging, they can be packed in strong cartons with proper packing materials such as bubble wrap or soft cloth and label the cartons Fragile. -
Page 17: Product Warning Label
• Do not clean the product or any e-system component with any detergent or organic solvent. Only clean the product with a water- dampened soft cloth. • Do not clean the product or any e-system component with pressured water. PRODUCT WARNING LABEL •... -
Page 18: Disposal
DISPOSAL • In accordance with Directive 2012/19/EU and Directive 2006/66/EC respectively, electronic devices that are no longer usable and defective/drained batteries must be collected separately and recycled in an environmentally friendly manner. • The e-system drive unit including the motor, driver, battery, speed sensor, HMI, accessories, and packaging should be disposed of in an environmentally correct manner.