Page 3
– in consideration of maximum allowed connecting power, warranty of 24 months is valid from the date of sale to the end buyer, but not more than 36 months after delivery from Smarteh. In case of claims within warranty time, which are based on material malfunctions the producer offers free replacement.
Longo Bluetooth Products LBT-1.B02 1.ABBREVIATIONS Light Emitted Diode Programmable Logic Controller Personal Computer OpCode Message Option Code Lux, the unit of illuminance Push button...
Mesh gateway connected to the same Bluetooth Mesh network. LBT-1.GWx Modbus RTU gateway is connected to the main control device as Smarteh LPC-3.GOT.012 7" PLC based Touch panel, any other PLC or any PC with Modbus RTU communication. Besides Smarteh Bluetooth Mesh devices, other standard Bluetooth Mesh devices can be integrated into above mentioned Bluetooth Mesh network.
Longo Bluetooth Products LBT-1.B02 3.FEATURES Figure 1: LBT-1.B02 Table 1: Features Communication standard: Bluetooth Mesh is a low power wireless mesh protocol and allows device to device communication and device to main control device communication. Radio frequency: 2.4GHz Radio range for direct connection: < 30m, depending on application and building.
Longo Bluetooth Products LBT-1.B02 4.OPERATION LBT-1.B02 Bluetooth Mesh multisensor can only operate with Smarteh LBT-1.GWx Modbus RTU Bluetooth Mesh gateway while provisioned to the same Bluetooth Mesh network. Figure 2: LBT-1.B02 device connection Figure 3: Bluetooth Mesh system topology...
NOTE: When the voltage of two installed AA batteries in series is lower than 2.2 V, LBT-1.B02 multisensor detects low battery condition. If the batteries are not replaced soon, the multisensor will switch off. Voltage level of the batteries can be monitored regularly i.e. on the Smarteh LPC-3.GOT.012 PLC based Touch panel or similar.
LBT-1.B02 Bluetooth Mesh multisensor accepts a set of operation codes as specified in below tables 2 to 4. LBT-1.B02 Bluetooth Mesh multisensor is communicating with the main control device as Smarteh LPC-3.GOT.012 via Smarteh LBT-1.GWx Modbus RTU Bluetooth Mesh gateway.
Page 11
Longo Bluetooth Products LBT-1.B02 Table 3: 3xxxx, Input registers, Modbus RTU to Bluetooth Mesh gateway Raw → Engineering data Reg. Name Description Number of messages pending in 1 .. 10 → 1 .. 10 Messages pending receiving buffer Destination node address. Can →...
Page 12
Longo Bluetooth Products LBT-1.B02 Table 4: Multisensor LBT-1.B02 option codes Option Raw → Engineering data Name Description code → FW version status Firmware version status 0 .. 65535 0 .. 65535 0 → Not used 1 → Not used 2 → Not used...
Longo Bluetooth Products LBT-1.B02 5.INSTALLATION Table 5: Connectors and switches Switch Vandal switch: close = not active, open = active K1.1 Power supply, 7..30 V DC K1.2 Power supply, GND Bat.1 Battery Alkaline AA/LR6 1.5 V high capacity battery, non rechargeable Bat.2...
Page 14
Longo Bluetooth Products LBT-1.B02 Table 6: Push buttons and LEDs Bottom-right Button press notification push button Upper-right Button press notification push button Upper-left Button press notification or push button Mode setting: Inside 5-second time window, perform a corresponding number of simultaneous pressing of PB3 and PB4 in duration of not less than 200 ms.
Longo Bluetooth Products LBT-1.B02 5.1. Mounting instructions Figure 6: Housing dimensions Dimensions in millimeters. Figure 7: Screw holes positions...
Page 16
Longo Bluetooth Products LBT-1.B02 Figure 8: Mounting instructions...
Page 17
Longo Bluetooth Products LBT-1.B02 Figure 9: Installation flowchart...
Page 18
LED blinking once per 10 sec. *NOTE: Smarteh Bluetooth Mesh products are added and connected to a Bluetooth Mesh network by using standard provisioning and configuration mobile apps tool such as nRF Mesh or similar.
Longo Bluetooth Products LBT-1.B02 5.2. Maintenance The LBT-1.B02 multisensor is maintenance free. Only two AA batteries require replacement with the new one when empty. On the main control device i.e. LPC-3.GOT.012, the indication for replacing the batteries will become active. If batteries will not be replaced approximately in one month after the battery warning appear for the first time, multisensor will switch off.
Longo Bluetooth Products LBT-1.B02 6.SYSTEM OPERATION 6.1. Interference warning Common sources of unwanted interference are devices that generate high frequency signals. These are typically computers, audio and video systems, electronics transformers, power supplies and various ballasts. The distance of the LBT-1.B02 multisensor to the above mentioned devices should be at least 0.5m or greater.
Longo Bluetooth Products LBT-1.B02 7.TECHNICAL SPECIFICATIONS Table 7: Technical specifications 2 high capacity batteries alkaline AA type (LR6) or external power supply 7 .. 30 V DC. Power supply Can not be connected in parallel, only a separate connection is allowed.
Longo Bluetooth Products LBT-1.B02 9.CHANGES The following table describes all the changes to the document. Date Description 12.10.23 The initial version, issued as LBT-1.B02 multisensor UserManual.
Need help?
Do you have a question about the Longo Bluetooth Products LBT-1.B02 and is the answer not in the manual?
Questions and answers