Jansno X70 Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

W W W. JANSNO.COM

X70

Electric Bicycle

MANUAL

Table of Contents

Summary of Contents for Jansno X70

Page 1 W W W. JANSNO.COM Electric Bicycle MANUAL...
Page 2 If you have questions about your ability to properly assemble this unit, please consult a qualified bicycle service specialist before riding. If you need replacement parts or have questions pertaining to assembly of your bicycle, please contact us on the official website www.jansno.com After-sales videos Whatsapp...
Page 3 Batteries should be fully charged immediately ！ when they are received and immediately after each use for the recommended charge times (see below). · Li-lon (Lithium lon) batteries 4-6 hours. · For your personal and property safety, if no one is vigilant,please don't charge the battery indoors. We recommend that you consult a bicycle specialist if you have doubts or concerns as to your experience or ability to properly assembly, repair, or maintain your bicycle.
Page 4 HELMETS SAVE LIVES!!! ALWAYS WEAR A PROPERLY FITTED HELMET FITTING. MAKE SURE CORRECT WHEN YOU RIDE YOUR BICYCLE. YOUR HELMET COVERS YOUR FOREHEAD. DO NOT RIDE AT NIGHT. CPSC RECORDS SHOW THAT ABOUT 35% OF BICYCLE RELATED DEATHS OCCUR AFTER DARK. AVOID RIDING IN WET CONDITIONS.
Page 5 Please Retain your Sales Receipt as Proof of Purchase. Attach receipt here. Notes:...
Page 6 PREFACE PART 1 Precautions for bicycles ........PART 2 Before You Ride ........... PART 3 Assembly ............PART 4 Detailed Maintenance ........PART 5 Monitor Error Codes Solution......
Page 7 ALL-TERRAIN ELECTRIC BIKE...
Page 8 LCD Screen Display Indication of speed, mileage, Gear Increase Button gear, headlight and PAS, Power Off Switch Line Fault Warning, Function setting, etc Brake Lever Brake Cable Power Switch Gear Reduction Button L&R turn signal swich Accelerator Horn Activation Locks F*R Light Switch Electic Speed Button...
Page 9: Before You Ride
BEFORE YOU RIDE ABOUT THIS MANUAL It is important for you to understand your new bicycle. By reading this manual before you go out on your first ride, you'll know how to get better performance, comfort, and enjoyment from your new bicycle. It is also important that your first ride on your new bicycle is taken in a controlled environment, away from cars, obstacles, and other cyclists.
Page 10: Safety Checklist
SAFETY CHECKLIST Before every ride, it is important to carry out the following safety checks: 1. Brakes Ensure front and rear brakes work properly. · · Ensure brake shoe pads are not over worn and are correctly positioned in relation to the rims. Ensure brake control cables are lubricated, correctly adjusted and display no obvious wear.
Page 11: Frame And Fork
6. Cranks and Pedals · Ensure pedals are securely tightened to the cranks. Ensure cranks are securely tightened to the axle and are not bent. · 7. Derailleurs · Check that front and rear mechanisms are adjusted and function properly. Ensure shift and brake levers are attached to the handlebar, shift and brake.
Page 12 Throttles Throttles are equipped on some models of electric bicycles. Control adjustment button area Throttles operate by rotating the throttle towards the rider Throttle much like a motorcycle. They generally are the inner half of Car monitor the right side handlebar grip and may also contain a battery gauge.
Page 13: Battery Care And Information
Battery Care and Information Proper maintenance of batteries will maximize their lifespan and capacity. JANSNO X70 warranties your new batteries from the date of purchase only if properly cared for-refer to the limited warranty for details. Ruli use Li-lon (Lithium lon) batteries in all of our electric bicycles and scooters.
Page 14 Thank you to provide us with valuable suggestions. When maintaining and repairing your vehicle, give us your valuable suggestion card together with the after-sale card. We will listen to your suggestions actively and modify our deficiencies in time.
Page 15 BIKE ASSEMBLY MANUAL...
Page 16: Bicycle Assembly
Bicycle Assembly Assembly Guides Individual assembly guides for each bicycle model can be found packaged with your bicycle. Getting Started Open the carton from the top and remove the bicycle. Remove the straps and protective wrapping from the bicycle. Inspect the bicycle and all accessories and parts for possible shortages.
Page 17 LG 34Ah dual battery has high capacity and long battery life. The top battery is used first and then automatically switches to the second battery.
Page 18 LCD Screen Accelerator Double Suspesion Fork Headlight Removable Battery Turn signal Saddle Removable Battery Rear Turn Light Shock Absorber Speed Flywheel Front Disc Brake Chainset Chain...
Page 19: Pedals & Crank Set
Pedals & Crank Set Look for the letters “R” for right, and “L” for left, stamped on each pedal spindle. Start threading each pedal by hand to avoid stripping the threads. Tighten with a 15mm narrow open ended wrench. Note that the right hand pedal attaches to the chainwheel side crank arm with a right-hand (clockwise) thread.
Page 20 Front Wheel-Bolt-oninstallation 1. Make sure the brakes are loose enough to allow the wheel to pass through the brake pads easily. 2. Place wheel into fork dropouts. 3. Install retaining washers with raised lip pointed towards the fork, and insert into the small hole of the fork blade. NOTE: Some bikes may have step retaining washers in place of the retaining washer (shown in dotted box).
Page 21 Tighten both rear wheel axle nuts securely. Failure to do this may cause the rear wheel to dislodge from the frame dropouts resulting in serious damage or injury. ！ Periodically, disassemble the mechanism from the bicycle and inspect for any wear or damage and replace if necessary.
Page 22 Disc Brakes - Tektro 1. Check the tightness of the six disc mounting bolts holding the brake rotor onto the wheel. If you need to remove these bolts, be sure to us a thread-locking compound when re-installing them. 2. Make sure the two bolts securing the caliper adaptor bracket to the fork are tight.
Page 23 5. Install the wheel, making sure the brake rotor fits into the slot in the caliper. Center the caliper around the brake rotor, then tighten the caliper mounting boits. 6. Using the inner pad adjusting bolt, adjust the inside brake pad so it is as cose as possible to the rotor without rubbing.
Page 24: Derailleur Systems
DERAILLEUR SYSTEMS The derailleur system includes the font and rear derailleurs, the shift levers, and the derailleur control cables, all of which must function correctly for smooth gear shifting to occur. Derailleur Although the front and rear derailleurs are initially adjusted at the factory, you will need to inspect and readjust both before riding the bicycle.
Page 25: Final Check
Final Check · After all adjustments have been made, shift through every gear several times at varying speeds. This will ensure all your adjustments are correct and will allow you to pinpoint any trouble areas. If you encounter any problems, refer to the appropriate section and make any necessary adjustments.
Page 26: Schedule1-Lubrication
Correct routine maintenance of your new bike will ensure smooth running Longer lasting components-Safer riding-Lower running costs Every time you ride your bicycle, its condition changes. The more you ride, the more frequently maintenance will be required. We recommend you spend a little time on regular maintenance tasks. You should be able to accomplish most tasks.
Page 27: Drive Train
DRIVETRAIN The drivetrain of a bicycle refers to all parts that transmit power to the rear wheel including the pedals, chain, chainwheel, crank set and freewheel. R=Right L=Left Turn clockwise to tighten. Turn counter-clockwise to tighten. PEDALS Pedals are available in a variety of shapes sizes and materials, and each are designed with a particular purpose in mind.
Page 28 Problem Possible Cause Remedy Gear shifts not working - Derailleur cables - Lubricate/tighten/replace properly sticking/stretched/damaged cables - Front or rear derailleur not - Adjust derailleurs adjusted properly - Indexed shifting not adjusted - Adjust indexing properly Slipping chain - Excessively worn/chipped chainring - Replace chainring, sprockets or freewheel sprocket teeth and chain...
Page 29 Problem Possible Cause Remedy Freewheel does not rotate - Freewheel internal pawl pins - Lubricate. If problem persists, are jammed replace freewheel Brakes not working effectively - Brake blocks worn down - Replace brake blocks - Brake blocks/rim greasy, wet or dirty - Clean blocks and rim - Brake cables are - Clean/adjust/replace cables...
Page 30 Problem Possible Cause Remedy Steering not accurate - Wheels not aligned in frame - Align wheels correctly - Headset loose or binding - Adiust/tighten headset - Front forks or frame bent - Take bike to a bike shop for possible frame realignment Frequent punctures - Inner tube old or faulty - Replace Inner tube...
Page 31 Instrument ebike error status code meaning Status State Reason code meaning Normal status After the failure of the vehicle during this operation was repaired Try unplugging the left brake plug and see if E02 disappears, if you unplug Brake failure the right brake plug, will it disappear? Finally confirm which brake lever is the problem and contact professional customer service for replacement: Brake lever Battery undervoltage Battery drain...
Page 32 Communication ① Check the plug condition ; (send) failure ② The meter is damaged. Communication fail The P20 setting item is set to 0 ( when this fault occurs in the No. 2 protocol ) Please don't change too many parameters to avoid setting errors and restoring the factory ！...
Page 33: Installation Procedures
Installation procedures 1: First handlebar installation, try to pay attention to not tear off the waterproof wire connector. 2: Battery installation to be in place, press down hard, (battery key can be turned to lock the battery) and then open the battery in the upper right corner of the red switch.
Page 34 W W W.JANSNO.COM Ltd: Shenzhen Jansno Trading Co., Ltd Business E-mail: bp@jansno.com Add: 1306, No.19 Zhongxing Road, Longgang District, Shenzhen, Guangdong, China Wechat After-sales videos Whatsapp...