Summary of Contents for MSK SL 05-25 W / L
- Page 1 User Manual Snow machine MSK SL 05 - 25 W / L T:\Produkt Info SLX Series (Snow Line)\Anleitungen\BA MSK SLX 5-25 L W ab Software 7.0.0 EN_2020.doc...
-
Page 2: Table Of Contents
............................14 2.4.3 EMERGENCY STOP ......................14 DEVICE 2.4.4 OTOR AND ELECTRICAL OPERATING FUNDS ..................14 Functionality PERATIONAL AREA ..........................16 PERATION SEQUENCE ......................... 16 Hygiene YGIENE REQUIREMENTS ........................17 MSK SL 05-25 W / L from p.no. 10220 status 28.04.2020... - Page 3 RAIN THE WATER MANUALLY ......................27 Cleaning MPTY RESIDUAL WATER MANUALLY ..................... 28 LEAN THE MACHINE HOUSING ......................29 .......................... 29 ENEW WATER HOSES Maintenance 10.1 ATER BATH ............................30 MSK SL 05-25 W / L from p.no. 10220 status 28.04.2020...
- Page 4 ....................40 12.1.12 ATER INLET FAULT ........................41 12.1.13 PTIONAL SEWAGE PUMP FLOODED ....................41 12.1.14 ..................41 PTIONAL ROTATING FIELD MONITORING 12.1.15 PTIONAL LEVEL SENSOR HAS TRIGGERED ..................41 MSK SL 05-25 W / L from p.no. 10220 status 28.04.2020...
-
Page 5: General
The entire manual has been prepared for supervisors and operators, as well as for cleaning and maintenance personnel. 1.2 STANDARDS, SPECIFICATIONS AND GUIDELINES This chapter contains all relevant standards, specifications and guidelines for the MSK SLX Touch summarized in a chart. Component... -
Page 6: Contact Adress
Tel.: +49 (0) 7832 9777350 phone: +49 (0) 7832 9993193 Fax: +49 (0) 07832 976874 fax: +49 (0) 07832 976874 info@msk-snow.com info@msk-snow.com or the local customer service. Firm stamp MSK SL 05-25 W / L from p.no. 10220 status 28.04.2020... -
Page 7: Type Plate
1.4 TYPE PLATE The MSK SLX is identified with the following type plates: The type plate is made of PVC. The following data is shown on the type label: • Producer • Type • Serial number • Construction year • Refrigerant •... -
Page 8: Typography
Loosen screws (1) on the switch flap (2) above the water bath (3) with a tool by turning to the left and … Fig. 3). See the following example: MSK SL 05-25 W / L from p.no. 10220 status 28.04.2020... -
Page 9: Safety
SYSTEM DAMAGE This safety notice warns of potential sources of danger that can cause damage to property. NOTE This note provides general tips for optimal use and further information. MSK SL 05-25 W / L from p.no. 10220 status 28.04.2020... -
Page 10: Safety Data Sheet
2. Every working day before start-up, the operator has to carry out a visual inspection of the connections and the MSK SLX in general, as well as the functionality of all safety devices relevant to operation. 3. The operator must immediately report any deficiencies in safety equipment to the supervisor. -
Page 11: General Safety Instructions
Set up or lay water pipes and the machine in a frost-proof area. SYSTEM DAMAGE High-pressure cleaners are not allowed to be used to clean the MSK SLX, as water can penetrate the basic housing construction and damage electrical components. -
Page 12: Operator-Relevant Safety Equipment
5. Supply / power plug The supply pipe with the mains plug connects the MSK SLX to the mains. The supply pipe has to be firmly connected to the plug and must not be damaged. - Page 13 11. Rotating field control The phase sequence relay monitors the rotating field of the mains (only at 400V) connection. 12. Hall sender Monitors the gear motor. MSK SL 05-25 W / L from p.no. 10220 status 28.04.2020...
-
Page 14: Electrical System
The electrical equipment of the MSK Touch complies with EN 60204-1: 2018-09, part 1. 2.4.1 MAINS CONNECTION The MSK Touch is connected directly to the network. The rated current is <16A and the rated power is <0.5kW. Exact technical data, see type plate. - Page 15 NOTE Observe the attached instruction manual of the component manufacturer. MSK SL 05-25 W / L from p.no. 10220 status 28.04.2020...
-
Page 16: Functionality
FUNCTIONALITY 3.1 OPERATIONAL AREA The MSK SLX is exclusively intended for the production of snow from drinking water. 3.2 OPERATION SEQUENCE An internally cooled roller (evaporator roller) rotates in a water bath. The water freezes to ice on the surface of the drum. This ice is removed from the drum by a scraper and the characteristic, thin shape of the snow is created. -
Page 17: Hygiene
HYGIENE 4.1 HYGIENE REQUIREMENTS The MSK SLX is divided into three areas in accordance with EN 1672-2: 2007 Food processing machinery, part 2 Hygiene requirements: 4.1.1 FOOD SECTOR The food sector includes all components that come into contact with the product. -
Page 18: Scope Of Delivery
If components are defective or missing, the MSK customer service has to be informed immediately. – Check that the scope of delivery of the MSK SLX is complete and undamaged. 5.1 SCOPE OF DELIVERY FOR MSK SLX The scope of delivery for the MSK SLX consists of:... -
Page 19: Transport And Installation
Fig. 3 Forklift symbol 6.2 INSTALLATION NOTE If components are defective or missing, the Metzger MSK customer service must be informed immediately. Check that the scope of delivery of the MSK SLX is complete and undamaged. -
Page 20: Environmental Conditions
If additional documentation is required for safety reasons, it must be added to the machinery documentation. If the MSK SLX is set up on public area, a safety barrier must be erected around the MSK SLX. Measures to ensure that unauthorized persons do not have access must be taken/implemented and compliance with them monitored. -
Page 21: Connecting The Electrical System
The direction of rotation is indicated by the arrows on the compressor or gear motor. MSK SL 05-25 W / L from p.no. 10220 status 28.04.2020... -
Page 22: Connecting The Water Supplies
An aquastop valve has to be installed at the water connection. The MSK Group accepts no liability for water damage caused by failure to observe this! MSK SL 05-25 W / L from p.no. 10220... -
Page 23: Commissioning And Decommissioning
The MSK Group assumes no liability for water damage caused by failure to observe! 7.1.1 ENVIRONMENTAL CONDITIONS The MSK SLX is designed for use at an ambient temperature and a water temperature of + 4°C to + 40°C. If the water temperature is below + 8°C, there is a risk of icing on the evaporator unit. Water temperatures of over + 25°C can lead to poor snow quality (watery, not pourable). -
Page 24: Function Test
- The SLX or, if applicable, the switch box must be connected to the mains - Activate at least one MSK SLX and switch it on by pressing the ON switch. The water supply to the machine begins, the gear motor for the roller drive begins to redate. The chiller starts when the process water level is reached. -
Page 25: Decommissioning
When decommissioning for a short period, leave the MSK SLX on and off. When decommissioning the MSK SLX over a longer period of time Switch off the MSK SLX snow machine with the OFF button and leave it at the power connection for at least 60 minutes... -
Page 26: Operation
Do not open the housing cover and switching flap during ice production. Risk of frostbite on hands when accessing the roller. Temperature -20°C. Do not change the location of the MSK SLX during snow production, as well as control and safety devices. -
Page 27: Visual Inspection
The residual water must be completely drained if the rotary evaporator is to be put out of operation for a longer period of time and transported. Close the on-site water supply line. Empty residual water manually. MSK SL 05-25 W / L from p.no. 10220 status 28.04.2020... -
Page 28: Cleaning
CLEANING SYSTEM DAMAGE High-pressure cleaners must not be used to clean the MSK Touch, as water can penetrate the basic housing structure and damage electrical components. Clean the rotary evaporator without high pressure. NOTE Observe the safety data sheet for cleaning. -
Page 29: Clean The Machine Housing
Close the on-site drinking water supply line. Unscrew and replace water hoses. MSK SL 05-25 W / L from p.no. 10220 status 28.04.2020... -
Page 30: Maintenance
At least once a month, the ice slide and ice guides must be checked for contamination or calcification and cleaned if necessary. With every maintenance, the distance of the ice scraper must be checked and the ice scraper readjusted or renewed if necessary. MSK SL 05-25 W / L from p.no. 10220 status 28.04.2020... -
Page 31: Solenoid Valves (Optional)
10.3 SOLENOID VALVES (OPTIONAL) The solenoid valves for the residual water drainage and the water inlet must be checked for function by a butcher MSK service technician or refrigeration specialist and replaced if necessary. 10.4 ROTARY ENTRY AND FLANGE BEARING (OPTIONAL) -
Page 32: Electrical System
10.6.1 LIMIT SWITCH ON SWITCHING FLAP (OPTIONAL) The function of the limit switch on the switching flap must be checked at least once a year. MSK SL 05-25 W / L from p.no. 10220 status 28.04.2020... -
Page 33: Check The Refrigerant Circuit
The amount of refrigerant may not be sufficient. Have refrigerant refilled by a refrigeration specialist. Green color of the refrigerant indicator: Refrigerant ok. Yellow color of the refrigerant indicator: Refrigerant damp due to leaking refrigerant circuit. Notify refrigeration specialist. MSK SL 05-25 W / L from p.no. 10220 status 28.04.2020... -
Page 34: Expansion Valve (Optional)
10.8 ELECTRICAL SYSTEM At least once a year, the entire electrical system of the rotary evaporator, including the supply line, the on / off switch must be checked for function. MSK SL 05-25 W / L from p.no. 10220 status 28.04.2020... -
Page 35: Disorders
11 DISORDERS NOTE If a malfunction occurs, the MSK SLX must be switched off immediately. Operation may only continue after the fault has been checked and rectified. NOTE Observe the operating instructions of the SLX. Disorder Cause of error Troubleshooting... - Page 36 MSK service technician MSK SLX switches off a) Fuse in the control box has a) Check the fuses by a refrigeration completely tripped specialist service technician. MSK SL 05-25 W / L from p.no. 10220 status 28.04.2020...
- Page 37 If the fault cannot be remedied, please contact customer service or the Metzger refrigeration, ice and snow technicians. For phone numbers see point 1.3 contact address. MSK SL 05-25 W / L from p.no. 10220 status 28.04.2020...
-
Page 38: Led Messages
None of the light rings are on. 12.1.2 SYSTEM IN OPERATION The blue LED ring lights up continuously Blue 12.1.3 SYSTEM IN STANDBY MODE The red LED ring lights up continuously Blue MSK SL 05-25 W / L from p.no. 10220 status 28.04.2020... -
Page 39: Compressor Pendulum Protection
The red LED ring lights up in 1 second ON and 1 second OFF cycles Blue 12.1.7 HD DISORDER The blue and red LED ring lights up in 1 second ON and 1 second OFF cycles Blue MSK SL 05-25 W / L from p.no. 10220 status 28.04.2020... -
Page 40: Nd Disorder
The blue and red LED ring lights up in 2 to 1 cycles Blue 12.1.11 MOTOR PROTECTION DRIVE MOTOR The blue and red LED ring lights up in 2 to 2 cycles Blue MSK SL 05-25 W / L from p.no. 10220 status 28.04.2020... -
Page 41: Water Inlet Fault
The blue and red LED ring lights up in 4 to 1 cycles Blue 12.1.15 OPTIONAL LEVEL SENSOR HAS TRIGGERED The blue and red LED ring lights up in 5 to 1 cycles Blue MSK SL 05-25 W / L from p.no. 10220 status 28.04.2020...
Need help?
Do you have a question about the SL 05-25 W / L and is the answer not in the manual?
Questions and answers