Summary of Contents for FAAC DAAB Scan&Go Basic kit
- Page 1 USER MANUAL SCAN & GO Revision 2 FAAC Nordic AB BOX 125, SE-284 22 PERSTORP SWEDEN TEL. +46 435 77 95 00...
-
Page 2: Table Of Contents
USER MANUAL SCAN & GO Table of contents Introduction ..........................3 Components ..........................3 Scanner Units........................3 Ticket generation ....................... 3 2.2.1 SGB-DT1.4 (desktop printer) ..................3 Command cards ........................3 Operation ..........................5 ... -
Page 3: Introduction
USER MANUAL SCAN & GO 1 Introduction This document is a manual for the “softwareless” commissioning of a Scan&Go Basic kit which includes one scanner housing and one desktop printer. Please read the relevant technical sheets and ensure the technical installation is done as described in this document before continuing. 2 Components 2.1 Scanner Units The standalone scanner control unit, with integrated CCD scanner and LCD display, interprets the tickets... - Page 4 USER MANUAL SCAN & GO Remove permanent card: is used to remove a permanent card from the control unit memory ‐ Open barrier: is used to trigger one relay of the control unit ‐ Reboot: is used to reboot the control unit ‐ Set time: is used when synchronizing the time of a printer with a control unit. ‐...
-
Page 5: Operation
USER MANUAL SCAN & GO 4 Operation 4.1 Desktop printer : operation and configuration Plug the printer in and start to print. The SGB-DT1.4 does not require any configuration and is thus immediately operational. Paper requirements: POS direct thermal paper 79.5mm +/- 0.5mm ... -
Page 6: Print Access Tickets With The Desktop Printer
USER MANUAL SCAN & GO 4.1.1 Print access tickets with the desktop printer The desktop printer comes with three push buttons. The orange button is inactive. The grey and blue push buttons allow printing barcodes with a default validity. Blue button: generates by default single use tickets valid for 30 minutes ... -
Page 7: Print Statistics With The Desktop Printer (Admin Mode)
USER MANUAL SCAN & GO 4.1.3 Print statistics with the desktop printer (Admin mode) The desktop printer allows you to print statistics showing the number of tickets you generated with the grey and blue push button since the last statistics generation. Power the printer off ... -
Page 8: Configuration
USER MANUAL SCAN & GO 5 Configuration Configuring the scanner control units can be done without using configuration software. Simply scan barcode command cards and read the messages appearing on the display so you know where you are in the configuration process. When powering on the controller, the LCD display shows the serial number of the controller during a few seconds: Then the following default messages appear repeatedly: And: date and time... -
Page 9: How To Link An Additional Printer To A Scanner Controller
USER MANUAL SCAN & GO 5.1 How to link an additional printer to a scanner controller Each S&G Basic scanner control unit and printer comes with a “S&G Scanner” and “S&G Printer” identity card. This is a unique barcode card necessary for a softwareless commissioning. -
Page 10: How To Choose Languages
USER MANUAL SCAN & GO 5.2 How to choose languages In this example, we want the messages to appear in English, French and German. 1. Scan the card “S&G Scanner” to the scanner controller until the message ‘Please scan: Command card’ appears on the screen. 2. -
Page 11: How To Configure The Flow Direction Of A Controlled Access
USER MANUAL SCAN & GO 5.3 How to configure the flow direction of a controlled access The controller must be programmed in Entrance or Exit mode in order to allow coherent messages to appear on the display. The default mode is “Exit”. 5.3.1 Exit ... -
Page 12: How To Configure An Access In "Free Access" Mode
USER MANUAL SCAN & GO 5.4 How to configure an access in “Free access” mode? Scan the card « S&G Scanner » to the controller until the message ‘Please scan: Command card’ appears. Then scan the card “Free access” until the message ‘Free access configured’ appears. ... -
Page 13: How To Reset The Controller (Factory Defaults)
USER MANUAL SCAN & GO 5.6 How to reset the controller (Factory defaults) Scan the card « S&G Scanner » until the message ‘Please scan: Command card’ appears. Then scan the card “Restore factory defaults” until the message ‘Resetting….’ appears. The message ‘Reset OK’ appears when the reset procedure is finished. 5.7 Set timezone ... -
Page 14: How To Remove A Permanent Access Card
USER MANUAL SCAN & GO 5.9 How to remove a permanent access card Scan the card « S&G Scanner » until the message ‘Please scan: Command card’ appears. Then scan the command card “Remove permanent card” until the message ‘Please scan: Command card’ appears. ... -
Page 15: How To Print Parking Tickets With The Desktop Printer
USER MANUAL SCAN & GO 5.11 How to print parking tickets with the desktop printer The desktop printer comes with three push buttons. The orange one is not active. The other two allow printing barcodes. Each button generate barcodes with a default validity. Grey button (Multiple entry): This ticket can be used multiple times until the end of the day ... -
Page 16: How To Reboot The Controller
USER MANUAL SCAN & GO 5.13 How to reboot the controller Scan the card « S&G Scanner » until the message ‘Please scan: Command card’ appears. Then scan the command card “Reboot” During the reboot process, the LCD display is empty. 5.14 How to trigger the output relay of the control unit ... -
Page 17: Troubleshooting
USER MANUAL SCAN & GO 6 Troubleshooting 6.1 Fatal errors In most of the Fatal error cases, the electronic should be replaced. Please contact your DAS supplier. Fatal Error SPI timeout: Communication failure on the internal bus Fatal error Database error: Memory error ... -
Page 18: The Message "Ticket Invalid!" Or "Ticket Ignored" Appears
USER MANUAL SCAN & GO 7.7 The message “Ticket invalid!” or “Ticket ignored” appears This message appears during a configuration process, when you don’t respect the logical order of scanning command. 7.8 The printer is virtually linked and yet the display shows the message: “Ticket printed by another system!”... -
Page 19: Notes
USER MANUAL SCAN & GO Notes ... - Page 20 USER MANUAL SCAN & GO Notes ...
-
Page 22: Command Cards
USER MANUAL SCAN & GO ... - Page 23 USER MANUAL SCAN & GO ...
- Page 24 USER MANUAL SCAN & GO ...
- Page 25 USER MANUAL SCAN & GO ...
Need help?
Do you have a question about the DAAB Scan&Go Basic kit and is the answer not in the manual?
Questions and answers