Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ascent ACT AP8616B GPON OLT
Summary of Contents for Ascent ACT AP8616B GPON OLT
- Page 1 ACT AP8616B GPON OLT Hardware Installation Manual Revision C...
- Page 2 Installation Manual Revision C Copyright © 2024 Ascent Communication Technology Limited. All rights reserved. Reproduction in any manner whatsoever without the express written permission of Ascent Communication Technology is strictly forbidden. This document is produced to assist professional and properly trained personnel with installation and maintenance issues for the product.
-
Page 3: Table Of Contents
AP8616B GPON OLT Contents Chapter 1 Introduction of AP8616B GPON Access Device ........... 4 1.1 Standard Configuration ................4 1.2 Special Features Attribute Parameters of ACT GPON ......6 1.3 ROHS Description..................7 Chapter 2 Installation Preparation ................8 2.1 Cautions ....................8 2.2 Safety Advice .................... -
Page 4: Chapter 1 Introduction Of Ap8616B Gpon Access Device
AP8616B GPON OLT Chapter 1 Introduction of AP8616B GPON Access Device The document describes the characteristics and parameters of AP8616B GPON and gives an overview of ACT GPON. 1.1 Standard Configuration AP8616B GPON has 8 GPON SFP ports, 4 gigabit SFP/TX combo ports, 4 gigabit SFP ports, 4 10GE SFP+ ports, 1 console port, and 1 100M Ethernet management port. - Page 5 AP8616B GPON OLT If the indicator is always on, the link on the port is normal. ACT/link indicator of 10GE T1 to T4 port If the indicator flickers, the data is received or transmitted through the port. If the indicator is on, the ONU device has been connected;...
-
Page 6: Special Features Attribute Parameters Of Act Gpon
AP8616B GPON OLT 1.2 Special Features Attribute Parameters of ACT GPON Item Protocol IEEE 802.1d Spanning Tree Protocol IEEE 802.1p Class of Service IEEE 802.1q tagged VLAN Protocol Standard IEEE 802.3x Flow control IEEE 802.3ad Link aggregation IEEE 802.3ah Ethernet in the First Mile Task Force RFC 1058 RIP Standard of IP Routing Protocol RFC 1723 RIP v2... -
Page 7: Rohs Description
AP8616B GPON OLT 1.3 ROHS Description Figure 1-3 ROHS Description Solutions Provider for FTTx, RFoG, and HFC Page 7 of 20 www.ascentcomtec.com... -
Page 8: Chapter 2 Installation Preparation
AP8616B GPON OLT Chapter 2 Installation Preparation 2.1 Cautions Similar to other electronic products, the semiconductor chip easily gets damaged if you power on and off abruptly and frequently. To restart up the AP8616B GPON, you have to open the power on-off after the power is turned off for three to five seconds. -
Page 9: Requirements For Common Locations
AP8616B GPON OLT Seek for medical help, or judge the loss and seek for available help. 2.2.4 Electrostatic Discharge Prevention Electrostatic discharge may damage devices and circuits. Improper treatment may cause this device to malfunction completely or discontinuously. Move or locate the devices according to the measures of electrostatic discharge prevention, ensuring the chassis connects the ground. -
Page 10: Chapter 3 Installing Ap8616B Gpon Device
AP8616B GPON OLT Chapter 3 Installing AP8616B GPON Device Caution: Only professionals are allowed to install or replace the devices of this device. 3.1 Installation Flow of AP8616B GPON Figure 3-1 Installation Flow of AP8616B GPON 3.2 Installing the Machine Box of AP8616B GPON The machine box of AP8616B GPON can be installed on the desk or can be fixed to other cabinets. -
Page 11: Connecting The Port
AP8616B GPON OLT 3.2.2 Installing the Machine Box on the Cabinet The machine box of AP8616B GPON is fixed on the cabinet through the brackets. When you fix the brackets, the front panel of AP8616B GPON faces forward. The detailed operations are shown in Figure 3-2. Figure 3-2 Fixing the Machine Box of AP8616B GPON to the cabinet After the brackets are installed, install the GPON device on the cabinet. - Page 12 AP8616B GPON OLT Figure 3-5 Connecting the CLI Port of AP8616B GPON and the Computer Figure 3-6 Cable connection at the CLI port Note: The CLI port of AP8616B GPON does not support flow control. Therefore, you must set the option data flow control to none when you configure AP8616B GPON with the super terminal.
- Page 13 AP8616B GPON OLT 3.3.2 Connecting the GPON SFP Port AP8616B GPON has 8 GPON SFP ports. The indicators lie in the right side of these ports, indicating the LINK/ACT state. They are used to connect the GPON access devices and other ONUs. A single-mode SC optical fiber and a GPON optical module are needed for connect AP8616B GPON and other ONUs.
- Page 14 AP8616B GPON OLT 3.3.4 Connecting Gigabit Ethernet TX Port AP8616B GPON provides 4 fixed gigabit SFP/TX combo ports (G1 to G4). The indicators lie in the right side of these ports, indicating the LINK/ACT state. When the TX ports (G1 to G4) are used, the corresponding optical port cannot be used. Figure 3-9 Connecting the 1000M TX port and other devices To use the TX port, you can connect the TX port and other Ethernet devices with the direct-through or cross cable through the UTP port of the GPON access device.
-
Page 15: Checking After Installation
AP8616B GPON OLT Sending the normal phase TXD2+ Output of the data Sending the paraphase of TXD2- Output the data Receiving the paraphase of RXD1- Input the data Receiving the normal phase RXD2+ Input of the data Receiving the paraphase of RXD1- Input the data... -
Page 16: Chapter 4 Maintaining The Gpon Access Device
AP8616B GPON OLT Chapter 4 Maintaining the GPON Access Device Caution: 1) Before opening the chassis, make sure you have discharged the static electricity on your body and turned off the power of the GPON access device. 2) Before performing operations beside the power supply or on the chassis, turn off the power on-off and plug out the power cable. -
Page 17: Closing The Chassis
AP8616B GPON OLT 4.2 Closing the Chassis The section mainly describes how to put the cover and close the chassis. Do as follows: 1) Put them well according to their locations and joint them together along their sides. See the following figure. Figure 4-3 Closing the Chassis Procedure 1 Figure 4-4 Closing the Chassis Procedure 2 2) According to the figure above, put close the edges of bottom shell and the cover. -
Page 18: Chapter 5 Hardware Fault Analysis
AP8616B GPON OLT Chapter 5 Hardware Fault Analysis The part describes how to remove the fault from the GPON access device. 5.1 Fault Separation The key for resolving the systematic faults is to separate the fault from the system. You can compare what the system is doing with what the system should do to detect the fault. - Page 19 Phone: +84 243 795 5917 WEB: www.ascentcomtec.com EMAIL: sales@ascentcomtec.com Specifications and product availability are subject to change without notice. Copyright © 2024 Ascent Communication Technology Limited. All rights reserved. Ver. ACT_AP8616B_Hardware_ Installation_Manual_V1c_Mar_2019 Solutions Provider for FTTx, RFoG, and HFC Page 19 of 20 www.ascentcomtec.com...
Need help?
Do you have a question about the ACT AP8616B GPON OLT and is the answer not in the manual?
Questions and answers