Table of Contents
Advertisement
Quick Links
X-TREME BRUSH CUTTER
NON PISTON MOTOR
USE AND MAINTENANCE GUIDE
14-20 GPM
XBC60LF
XBC72LF
XBC78LF
Scan QR code for a digital version of this manual
Read and understand the manual. This manual provides information and
procedures to safely operate and maintain the X-Treme Brush Cutter.
16-26 GPM
20-30 GPM
XBC162660
XBC60MF
XBC162672
XBC72MF
XBC162678
XBC78MF
XBC162684
October 2023
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for IronCraft X-TREME XBC60LF
Summary of Contents for IronCraft X-TREME XBC60LF
- Page 1 X-TREME BRUSH CUTTER NON PISTON MOTOR USE AND MAINTENANCE GUIDE 14-20 GPM 16-26 GPM 20-30 GPM XBC60LF XBC162660 XBC60MF XBC72LF XBC162672 XBC72MF XBC78LF XBC162678 XBC78MF XBC162684 Scan QR code for a digital version of this manual Read and understand the manual. This manual provides information and October 2023 procedures to safely operate and maintain the X-Treme Brush Cutter.
-
Page 2: Table Of Contents
Maintenace Log � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 40 Revised October 5, 2023 5:35 PM ©2023 IronCraft Attachments. A ll rights reser ved. Ironcraftusa.com... -
Page 3: Register
WWW.IRONCRAFTUSA.COM/WARRANTY/REGISTER-WARRANTY/ Purchase date Dear Owner: We appreciate your business and thank you for choosing Ironcraft as your Dealer name provider of quality skid steer attachments. We are committed to providing you with a heavy duty product that will provide years of satisfaction and Address safe operation. -
Page 4: Model Comparison
SAFETY INFORMATION MODEL COMPARISON 1�1 INTRODUCTION SKID STEER X-TREME DUTY BRUSH CUTTER The following terms are used interchangeably throughout this manual. 14-20 GPM 20-30 GPM X-TREME BRUSH CUTTER SKID STEER OPERATOR XBC60 XBC72 XBC78 XBC84 XBC60 XBC72 XBC78 XBC84 MODEL implement, attachment, skid steer loader, product, machine,... - Page 5 1�2 SAFETY SYMbOLS SAFETY PICTOGRAMS This manual and decals on this machine use safety symbols, pictograms and color coded signal words to alert you to potential hazards that may cause death or severe injury if a safety instruction Pictograms are graphic symbols meant to alert you of a potential hazard. Read and understand the is ignored.
- Page 6 6" x 6" Danger Stay Back 300 Feet Decal. There is a label on the front left and the front right. decal to this machine. • Contact your local dealer to order replacement decals. IronCraft Logo Decal (not shown) Note: Non-Safety Decal SAFETY INFORMATION SAFETY INFORMATION Ironcraftusa.com...
- Page 7 1�4 SKID STEER LOADER REQUIREMENTS 1�5 GENERAL SAFETY INSTRUCTIONS Below are general safety instructions that relate to the overall operation and maintenance of this machine. It is important that you read and understand each message to prevent serious injury or death. CAUTION ALWAYS PREvENT...
-
Page 8: Operating Procedures
OPERATING PROCEDURES 4. A ctivate your skid steer’s lever lock switch to lock the pins into the flange slots of the brush Unpacking Your Brush Cutter cutter’s attachment plate. If your skid steer does not have this switch, manually lock the levers as Unpacking Your Brush Cutter shown in Figure 2.2b below. - Page 9 2�3 HOW TO START AND STOP NOTICE THE bRUSH CUTTER If the brush cutter begins to vibrate while increasing the RPM’s, deactivate the auxilary hydraulic system and investigate the cause. Refer to the Troubleshooting Chart on page 31 of this manual. bRUSH CUTTER CONTROLS Your brush cutter is designed to run off the skid steer loader’s auxiliary hydraulic system, and is activated and deactivated by a control in the operator’s cab.
- Page 10 2�4 FIRST TIME USE PROCEDURE START HERE 6 inches SKID STEER CHECK Before operating the brush cutter, check the skid steer’s hydraulic oil level FIGURE 2�4: AFTER STARTING SKID STEER, LIFT ATTACHMENT 6 INCHES OFF THE and add oil if necessary. GROUND SURFACE CASE DRAIN HOSE SKID STEER...
-
Page 11: Cutting Operations
2�5 CUTTING OPERATIONS BEFORE CUTTING GENERAL OPERATING TIPS ALWAYS LEARN inspect work area before starting the cutter. Locate and mark any utilities, steel posts, rocks or any other objects that could damage the brush cutter what the cutter head looks like in a level position when you are seated in the skid steer. Knowing during operation. -
Page 12: Maintenance Procedures
Tilt the front of the deck approximately 1 to 2 feet above ground level. Improper maintenance or modifications to the design or performance of this machine DO NOT raise the rear of the deck. will void the warranty. ONLY use genuine Ironcraft replacement parts on this machine. DRIVE SLOWLY SAFETY INSTRUCTIONS into the vegetation and use the skid steer tilt function to push the vegetation forward. -
Page 13: Maintenance Schedule
3�2 MAINTENANCE SCHEDULE 3�3 STORAGE This brush cutter attachment will provide years of dependable service if routine maintenance procedures are performed. The maintenance tasks listed below are based on normal operating conditions. More frequent maintenance may be necessary with intense use or when operating in STORAGE TIPS adverse environmental conditions. -
Page 14: Blade Holder Removal
3�4 bLADE HOLDER REMOvAL WARNING To avoid an accident that could result in death or serious injury, NEVER place your body under an unsupported cutter deck when servicing this brush cutter. ONLY service the brush cutter on stable, even terrain. NEVER park on sloped terrain to avoid being struck and killed or seriously injured by the unexpected rolling or movement of the skid steer. -
Page 15: Blade Removal Procedures
3�6 bLADE REMOvAL CAUTION Cutter blades are sharp and could cut you if mishandled. ALWAYS wear protective gloves and footwear when handling cutter blades. NOTICE This procedure requires special tools and skills. DO NOT attempt to remove or sharpen blades if you do not have the tools or skills. Take your brush cutter to your local dealer for blade services. -
Page 16: Blade Installation Procedures
3�8 GEARbOX MOTOR MAINTENANCE 3�7 bLADE INSTALLATION NOTICE NOTICE Maintenance procedures for the gear box motor require special tools and skills. DO Disconnect the negative ground cable from your skid steer’s battery when NOT attempt to service the gear box motor unless you have the tools and skills to do performing this procedure with the brush cutter attached to the skid steer. -
Page 17: Troubleshooting
TROUBLESHOOTING 3�9 TORQUE SPECIFICATION TAbLE 4�1 TROUbLESHOOTING CHART TORQUE vALUES SAE GRADE 8 LUBRICATED PROBLEM CAUSE RESOLUTION LB-FT LT-FT Deck is not properly leveled & Refer to leveling instructions found in material is balling under deck this manual. 1/4” Dull blades Remove and sharpen blades. -
Page 18: Specifications
SPECIFICATIONS PARTS INFORMATION Factory fresh parts specifically designed for your implement are readily available. MINI SKID STEER (MSS) X-TREME DUTY BRUSH CUTTER For hassle free service and to ensure you receive the correct parts for your implement, please provide your dealer with the following information: 14-20 GPM 20-30 GPM MODEL XBC60LF XBC72LF XBC78LF... - Page 19 6�1 PARTS ASSEMbLY DIAGRAMS Low Flow (14-20 GPM) Mid Flow (20-30 GPM) DESCRIPTION QTY. PARTS NUMBER DESCRIPTION QTY. PARTS NUMBER Cutter Deck Weldment Cutter Deck Weldment Gear Box - 100 HP Gear Box - 100 HP Shear Bolt & Nut Set Shear Bolt &...
-
Page 20: Warranty Information
Ironcraft reserves the right to make improvements in design or changes in specifications at any time without incurring any obligations to owners of Ironcraft will ship a replacement part with a Service Request Form and RGA #. There will be a call previously purchased products. No one but Ironcraft is allowed to alter, modify or enlarge this tag with the Manufacturer’s address and instructions for returning the defective part. -
Page 21: Safety Acknowledgement Forms
SAFETY ACKNOWLEDGEMENT FORM OPERATOR NAME SIGNATURE DATE ATTN ALL OPERATORS: Print your name, sign and date in the boxes below to acknowledge that you have read and fully understand the safety instructions presented in this manual, and have been trained on how to safely operate this attachment. OPERATOR NAME SIGNATURE DATE... -
Page 22: Maintenace Log
MAINTENANCE LOG DESCRIPTION OF MAINTENANCE SERVICED BY DATE Use this log sheet to document all routine maintenance and repair services performed on this machine. DESCRIPTION OF MAINTENANCE SERVICED BY DATE MAINTENANCE LOG MAINTENANCE LOG Ironcraftusa.com Ironcraftusa.com... -
Page 23: Revised October 5, 2023 5:35 Pm
7 rocky MT rd Athens, Tennessee 37303 (p) 423-405-5150 (f) 423-405-5904 www�ironcraftusa�com Revised October 5, 2023 5:35 PM ©2023 IronCraft Attachments. A ll rights reser ved. XBCLFMFM A N01...
Need help?
Do you have a question about the X-TREME XBC60LF and is the answer not in the manual?
Questions and answers