Advertisement

Quick Links

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
The vendor makes no representations or warranties with respect to the contents here and specially disclaims
any implied warranties of merchantability or fitness for any purpose. Further the vendor reserves the right
to revise this publication and to make changes to the contents here without obligation to notify any party
beforehand.
Duplication of this publication, in part or in whole, is not allowed without first obtaining the vendor's approval
in writing.
The content of this user's manual is subject to be changed without notice and we will not be responsible for
any mistakes found in this user's manual. All the brand and product names are trademarks of their respective
companies.

FCC Information and Copyright

Dichiarazione di conformità sintetica
Ai sensi dell'art. 2 comma 3 del D.M. 275 del
30/10/2002
Si dichiara che questo prodotto è conforme
alle normative vigenti e soddisfa i requisiti
essenziali richiesti dalle direttive
2004/108/CE, 2006/95/CE e 1999/05/CE
quando ad esso applicabili
Short Declaration of conformity
We declare this product is complying with the
laws in force and meeting all the essential
requirements as specified by the directives
2004/108/CE, 2006/95/CE and 1999/05/CE
whenever these laws may be applied

Advertisement

Table of Contents
loading

Summary of Contents for Biostar BIQ67-AHP

  • Page 1: Fcc Information And Copyright

    FCC Information and Copyright This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
  • Page 2: Table Of Contents

    Table Of Contents FCC Information and Copyright ������������������������������������������������������������������������������� 1 Chapter 1: Introduction ������������������������������������������������������������������������������������������� 3 1.1 Before You Start .............................3 1.2 Specifications ............................4 1.3 Rear Panel Connectors ...........................7 1.4 Motherboard Layout ..........................8 Chapter 2: Hardware installation ����������������������������������������������������������������������������� 9 2.1 Install Central Processing Unit (CPU) .....................9 2.2 Install a Heatsink ..........................11 2.3 Fan Headers ............................12 2.4 Install System Memory .........................13...
  • Page 3: Chapter 1: Introduction

    BIQ67-AHP User’s Manual Chapter 1: Introduction 1.1 Before You Start Thank you for choosing our product. Before you start installing the motherboard, please make sure you follow the instructions below: •  Prepare a dry and stable working environment with sufficient lighting.
  • Page 4: Specifications

    1.2 Specifications Dimensions 305 x 244 x 1.6 mm, ATX form factor Processor LGA1700 Socket, 14 Intel Core Processor (Max TDP at 125W) Core Logic (PCH) Intel® Q670/ W680 LAN controller: 1 x Intel® i226V 1 x Intel® i226LM Chipsets Audio Codec: ALC897 Audio Amplifier: ALC105 Super IO : F81966...
  • Page 5 BIQ67-AHP User’s Manual Buzzer 1 x Buzzer 1 x 16-Bit DIO header (by BIOS setting) 5V/3.3V switch by jumper, default 5V, Pull high/pull low control Digital I/O by jumper, default low Hardware monitor CPU/System temperature, Voltage monitoring for VCC, 3.3, 5, 12V...
  • Page 6 Operation Temp. 0 ºC ~ 60 ºC Humidity : 5% ~ 90% Storage Temp. -10 ºC ~ 70 ºC Humidity : 5% ~ 90% 6 | Chapter 1: Introduction...
  • Page 7: Rear Panel Connectors

    BIQ67-AHP User’s Manual 1.3 Rear Panel Connectors COM1/COM2: Serial port Connectors (RS-232/RS-422/RS-485) RS-232 (Default) RS-422* RS-485* Pin Assignment Carrier detect (DCD) 422 TXD- 485 DATA- Received data (RXD) 422 TXD+ 485 DATA+ Transmitted data (TXD) 422 RXD+ Data terminal ready (DTR) 422 RXD-...
  • Page 8: Motherboard Layout

    1.4 Motherboard Layout »  »  represents the 1st pin. 8 | Chapter 1: Introduction...
  • Page 9: Chapter 2: Hardware Installation

    BIQ67-AHP User’s Manual Chapter 2: Hardware installation 2.1 Install Central Processing Unit (CPU) Step 1: Locate the CPU socket on the motherboard Note »  » Remove pin cap before installation, and make good preservation for future use. When the CPU is removed, cover  the pin cap on the empty socket to ensure pin legs won’t be damaged. »  » The motherboard might equip with two different types of pin cap. Please refer below instruction to remove the  pin cap. Step 2: Open ILM Lever and then load plate using finger tab...
  • Page 10 Step 4: Close the load plate Step 5: Remove and save cover Step 6: Close ILM Lever and latch Note »  » Ensure that you install the correct CPU designed for LGA1700 socket. »  » The CPU fits only in one correct orientation. Do not force the CPU into the socket to prevent damaging the CPU. 10 | Chapter 2: Hardware installation...
  • Page 11: Install A Heatsink

    BIQ67-AHP User’s Manual 2.2 Install a Heatsink Step 1: Place the CPU fan assembly on top of the installed CPU and make sure that the four fasteners match the motherboard holes. Orient the assembly and make the fan cable is closest to the CPU fan connector.
  • Page 12: Fan Headers

    2.3 Fan Headers These fan headers support cooling-fans built in the computer. The fan cable and connector may be different according to the fan manufacturer. Connect the fan cable to the connector while matching the black wire to pin#1. CPU_FAN1/ SYS_FAN1: WAFER 1X4 2.54MM Pin Assignment FANPVOUT FAN_TACH...
  • Page 13: Install System Memory

    BIQ67-AHP User’s Manual 2.4 Install System Memory DDR4 Modules Step 1: Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM on the slot such that the notch on the DIMM matches the break on the slot.
  • Page 14 Memory Capacity DIMM Socket Location DDR4 Module Total Memory Size DDR4_A1 8GB/16GB/32GB DDR4_A2 8GB/16GB/32GB Max is 128GB. DDR4_B1 8GB/16GB/32GB DDR4_B2 8GB/16GB/32GB Dual Channel Memory Installation Please refer to the following requirements to activate Dual Channel function: Install memory module of the same density in pairs, shown in the table. Dual Channel Status DDR4_A1 DDR4_A2...
  • Page 15: Expansion Slots

    BIQ67-AHP User’s Manual 2.5 Expansion Slots PEX16_1/PEX16_2: PCI-Express x16 Slot (x16 or x8 speed) •  PCI-Express 4.0 compliant. •  The maximum bandwidth of the PCIe slot is 64GB/s or 32GB/s in total. PEX4_1/PEX4_2/PEX4_3: PCI-Express x4 Slot •  PCI-Express 4.0 compliant.
  • Page 16 M2M_1: M.2 (Key M) Slot •  The M.2 slot supports M.2 Type 2242/2280 module. When installing M.2 module, please place the screw and hex pillar to correct position. M2B_1: M.2 (Key B) Slot •  The M.2 slot supports M.2 Type 3042/2252 module. When installing M.2 module, please place the screw and hex pillar to correct position.
  • Page 17 BIQ67-AHP User’s Manual M2E_1: M.2 (E Key) Socket •  Support M.2 socket 2230 type module. •  Supports WiFi/ Bluetooth module and Intel® CNVi (Integrated WiFi/ BT). Install an Expansion Card You can install your expansion card by following steps: •  Read the related expansion card’s instruction document before install the expansion card into the computer.
  • Page 18: Headers / Connectors

    2.6 Headers / Connectors DC1: POWER CONN ATX 24P-B For better compatibility, we recommend to use a standard ATX 24-pin power supply for this connector. Make sure to find the correct orientation before plugging the connector. Assignment Assignment +3.3V +3.3V -12V +3.3V Ground...
  • Page 19 BIQ67-AHP User’s Manual F_PANEL1: Front Panel Header This connector includes Power-on, Reset, HDD LED and Power LED connections. It allows user to connect the PC case’s front panel switch functions. Assignment Assignment HDD_LED+ POWER_LED+ HDD_LED- POWER_LED- PWRBTN_N FP_RST_N JSPK1: Chassis Speaker Header Please connect the chassis speaker to this header.
  • Page 20 SATA1/SATA2/SATA3/SATA4/SATA5/SATA6/SATA7/SATA8: Serial ATA 6.0 Gb/s Connectors The connector supports the thin Serial ATA cable for primary internal storage devices. Pin Assignment SSATA_TXP1 SSATA_TXN1 SSATA_RXN1 SSATA_RXP1 Note »  » SATA1-SATA4 colay with 1x PCIex4 (PEX4_3) F_USB32_A-5G1: Header for USB 3.2 (Gen1) Ports at Front Panel This header allows user to add additional USB ports on the PC front panel, and also can be connected with a wide range of external peripherals.
  • Page 21 BIQ67-AHP User’s Manual JPRNT1: Printer Port Connector This header allows you to connector printer on the PC. Pin Assignment Pin Assignment STB# PRD0 EEROR# PRD1 PINIT# PRD2 SLCTIN# PRD3 PRD4 PRD5 PRD6 PRD7 ACK# BUSY SLCT VCC5/VCC3_3 JCOM3/JCOM4/JCOM5/JCOM6: Serial Port Headers Pin Assignment .-PDCD...
  • Page 22 JSMB1 Pin Assignment SMB_CLK_HDR SMB_DATA_HDR SMB_ALERT_N +3V3_DUAL SIM1 Pin Assignment UIM_PWR UIM_Reset UIM_CLK Data 22 | Chapter 2: Hardware installation...
  • Page 23: Jumpers / Slot

    BIQ67-AHP User’s Manual 2.7 Jumpers / Slot Jumper Setting The illustration shows how to set up jumpers. When the jumper cap is placed on pins, the jumper is “close”, if not, that means the jumper is “open”. Pin opened Pin closed...
  • Page 24 JP1/JP2/JP3/JP4/JP5/JP6 JP1 - JP6 Ring JATX1: HEADER 1X3 Pin Assignment AT-ATX JDIO-POWER JDIO-POWE VCC3_3 JPDIO1 PU-PD FUNCTION DIO/PRNT JDIO-POWER FUNCTION DIO/PRNT 24 | Chapter 2: Hardware installation...

Table of Contents