Tempro TP527 Operating Instructions

LIMITED WARRANTY
CHECKOUT PROCEDURE
TEMPRO ONE-YEAR LIMITED WARRANTY.
MODELS COVERED IN THIS MANUAL, ARE WARRANTED BY TEMPRO TO THE ORIGINAL
USER AGAINST DEFECTS IN WORKMANSHIP OR MATERIALS UNDER NORMAL USE FOR
ONE YEAR AFTER DATE OF PURCHASE. ANY PART WHICH IS DETERMINED TO BE
DEFECTIVE IN MATERIAL OR
AND RETURNED TO AN AUTHORIZED SERVICE LOCATION, AS TEMPRO DESIGNATES,
SHIPPING COSTS PREPAID, WILL BE, AS THE EXCLUSIVE REMEDY, REPAIRED OR
REPLACED AT TEMPRO'S OPTION. FOR LIMITED WARRANTY CLAIM PROCEDURES,
SEE "PROMPT DISPOSITION" BELOW. THIS LIMITED WARRANTY GIVES PURCHASERS
SPECIFIC LEGAL RIGHTS WHICH VARY FROM JURISDICTION TO JURISDICTION.
LIMITATION OF LIABILITY.
TEMPRO'S LIABILITY FOR CONSEQUENTIAL AND INCIDENTAL DAMAGES IS
EXPRESSLY DISCLAIMED. TEMPRO'S LIABILITY IN ALL EVENTS IS LIMITED TO AND
SHALL NOT EXCEED THE PURCHASE PRICE PAID.
WARRANTY DISCLAIMER.
PRODUCT INFORMATION AND ILLUSTRATE THE PRODUCTS IN THIS LITERATURE
ACCURATELY; HOWEVER, SUCH INFORMATION AND ILLUSTRATIONS ARE FOR THE
SOLE PURPOSE OF IDENTIFICATION, AND DO NOT EXPRESS OR IMPLY A WARRANTY
THAT THE PRODUCTS ARE MERCHANTABLE, OR FIT FOR A PARTICULAR PURPOSE,
OR THAT THE PRODUCTS WILL NECESSARILY CONFORM TO THE ILLUSTRATIONS OR
DESCRIPTIONS. EXCEPT AS PROVIDED BELOW, NO WARRANTY OR AFFIRMATION OF
FACT, EXPRESSED OR IMPLIED, OTHER THAN AS STATED IN THE "LIMITED WARRANTY"
ABOVE IS MADE OR AUTHORIZED BY TEMPRO.
Technical Advice and Recommendations, Disclaimer.
practice or dealings or trade custom, sales shall not include the furnishing of technical
advice or assistance or system design. Tempro assumes no obligations or liability on
account of any unauthorized recommendations, opinions or advice as to the choice,
Operation
installation or use of products.
Product Suitability.
construction, installation, and/or use of products for certain purposes, which may vary
from those in neighboring areas. While attempts are made to assure that Tempro
products comply with such codes, Tempro cannot guarantee compliance, and cannot be
responsible for how the product is installed or used. Before purchase and use of a
product, review the product applications, and all applicable national and local codes and
regulations, and be sure that the product, installation, and use will comply with them.
Certain aspects of disclaimers are not applicable to consumer products; e.g., (a) some
jurisdictions do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you; (b) also, some
jurisdictions do not allow a limitation on how long an implied warranty lasts,
consequently the above limitation may not apply
to you; and (c) by law, during the period of this Limited Warranty, any implied
warranties of implied merchantability or fitness for a particular purpose applicable
to consumer products purchased by consumers, may not be excluded or otherwise
disclaimed.
Prompt Disposition.
adjustment with respect to any product which proves to be defective within limited
warranty. For any product believed to be defective within limited warranty, first write
or call dealer from whom the product was purchased. Dealer will give additional
directions. If unable to resolve satisfactorily, write to Tempro at address below, giving
NOTE
dealer's name, address, date, and number of dealer's invoice, and describing the nature
of the defect. Title and risk of loss pass to buyer on delivery to common carrier. If product
was damaged in transit to you, file claim with carrier
Tempro Brand, A Division of Senasys www.tempro-products.com
1435 International Dr. 715-831-6353
Eau Claire, WI 54701
™
TEMPRO IMMERSION CONTROLLERS,
WORKMANSHIP
TO THE EXTENT ALLOWABLE UNDER APPLICABLE LAW,
A DILIGENT EFFORT HAS BEEN MADE TO PROVIDE
Notwithstanding any past
Many jurisdictions have codes and regulations governing sales,
A good faith effort will be made for prompt correction or other
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect
yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage!
Retain instructions for future reference.
General Safety Information
Disconnect all power
before installing or
servicing this product. If the power
disconnect is out of view, lock it in the
open position and tag it to prevent
unexpected restarting of power. Failure to
do so could result in fatal electric shock.
intended for limiting or regulating
temperatures. They must NOT be used
in potentially dangerous locations such
as flammable, explosive, chemical laden
areas or in wet atmospheres.
as operating controls only. Where an
operating control failure would result in
personal injury and/or loss of property, it
is the responsibility of the installer to add
Do not depend upon
devices (safety, limit controls) or systems
the thermostat as the
(supervisory alarm systems) that protect
sole means of disconnecting power when
against, or warn of control failure.
installing or servicing the product it is
controlling. Always disconnect power
at the main circuit breaker as described
above. Failure to do so could result
in fatal electric shock.
Senasys
Eau Claire, WI 54701
Installation
LOCATION
MOUNTING – IMMERSION
CONTROLLER & BULB
These immersion
controllers are
Do not dent or deform
the sensor coil of
These thermostats
this control. A dent or deformation
are designed for use
will change the calibration and cause
the control to cycle at a temperature
lower than the knob setting.