1. Manuals
  2. Brands
  3. Erwin Sattler Manuals
  4. Household Appliance
  5. Troja
  6. User manual

Erwin Sattler Troja User Manual

Watch winder
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
User manual
Troja watch winder

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Troja and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Erwin Sattler Troja

  • Page 1 User manual Troja watch winder...

  • Page 2: Table Of Contents

    Assembly instruction Thank you very much for your confidence. Your watch winder has been for Troja 16 M, Troja Lunaris M made in our company with high manufactural expenditure and has and Troja Sonata M been assembled and adjusted by our clockmakers in the traditional way.
  • Page 3 Resetting the watches especially with complications like perpetual calendars can often be time consuming. Erwin Sattler watch winders will fulfil this task in a perfect way. The advanced ERWIN SATTLER - BELUWO - technology allows each single watch winder unit to adapt to any automatic watch movement.

  • Page 4: Assembly Instruction

    Troja 16 M, Troja Lunaris M and Troja Sonata M The Troja 16 will be shipped in one box Installation of the Troja 16 M, Troja Lunaris M and Troja Sonata M Take out the movement 1. Unpacking the case top...
  • Page 5 Troja 16 M The precision pendulum clock Caliber 1965 Precision pendulum clock, extendible watch winder and safe Your decision to purchase the precision pendulum clock with seconds pendulum shows that you belong to the very small circle of special connoisseurs of highest mechanical clockmaking art.
  • Page 6 Start up the clock How to fit in the movement Remove the safety rubber band from the pallet lever. Push the movement on the 4 pillars and screw See assembly instruction page 6. it down with the four knurled nuts. Remove the transport protection of the escapement lever. Caution! So that motion can be transmitted from the movement to the pendulum, the driving pin of the With the clock, there is a protecting cover that has to be laid inside the bottom of the...
  • Page 7 How to start the clock Before hanging the weight into the pulley, make sure the cable runs in the front groove of the guide pulley. Wind the clock with the crank one turn counter clock wise. Deflect the pendulum until a Compensation tube »tick«, caused by the drop of the escapement wheel tooth on the pallet, is audible.
  • Page 8 Technical specifications Due to the fact that every place on earth has a different gravitation, a clock that runs +/- 0 sec in Munich/Germany will gain or loose time if it is located somewhere else. Classica Secunda 1995 – Cal. 1965 As an example see the list below: •...

  • Page 9: Troja 16 M

    Press and hold the button If you start up the Troja 16 M (connect it to the power supply) for the first time at 8.00 a.m., for example, the watch winder begins moving at 8.00 a.m. every day. From this point on, the watch winder units will start from 8 a.m. till 12 p.m. every day so then have they a stationary phase lasting 10 hours.

  • Page 10: The Precision Pendulum Clock

    Troja Lunaris M The precision pendulum clock Caliber 1915 Precision pendulum clock, calendar, moon phase, extendible watch winder and safe Your decision to purchase the precision pendulum clock with seconds pendulum shows that you belong to the very small circle of special connoisseurs of highest mechanical clockmaking art.

  • Page 11: Start Up The Clock

    Start up the clock How to fit in the movement Remove the safety rubber band from the pallet lever. Push the movement on the 4 pillars and screw See assembly instruction page 6. it down with the four knurled nuts. Remove the transport protection of the escapement lever. Caution! So that motion can be transmitted from the movement to the pendulum, the driving pin of the With the clock, there is a protecting cover that has to be laid inside the bottom of...
  • Page 12 How to start the clock Before hanging the weight into the pulley, make sure the steel cable runs in the front groove of the guide pulley. Wind the clock with the crank one turn counter clock wise. Deflect the pendulum until Compensation tube a »tick«, caused by the drop of the escapement wheel tooth on the pallet, is audible.
  • Page 13 The accessory box Due to the fact that every place on earth has a different gravitation, a clock that runs +/- 0 sec in Munich/Germany will gain or loose time if it is located somewhere else. When the front door is completely opened, you can pull out the box cover. In the bottom of the As an example see the list below: case you find the accessories as shown in the picture below.

  • Page 14: Troja Lunaris M

    Press and hold the button If you start up the Troja Lunaris M (connect it to the power supply) for the first time at 8.00 a.m., for example, the watch winder begins moving at 8.00 a.m. every day. From this point on, the watch winder units will start from 8 a.m. till 12 p.m. every day so then have they a stationary phase lasting 10 hours.
  • Page 15 Troja Sonata M The precision pendulum clock with strike train Caliber 2015 Precision pendulum clock, strike train, moon phase, extendible watch winder and safe Your decision to purchase the precision pendulum clock with seconds pendulum shows that you belong to the very small circle of special connoisseurs of highest mechanical clockmaking art.

  • Page 16: Start Up The Clock

    Start up the clock So that motion can be transmitted from the movement to the pendulum, the driving pin of the pallet lever must be inserted in the triangular cut-out in the safety flap on the beat adjuster. See assembly instruction page 6. To do so, reach behind the movement from the side, carefully press the lever with the cut-out backwards and upwards until the driving pin slots into the triangular cut-out.
  • Page 17 Adjusting the striking mechanism The striking mechanism’s hammer is generally factory adjusted. If, however, the hammer should have gone out of adjustment (perhaps as a result of being transported), it can be readjusted by means of a special mechanism on the rear of the movement. This will be necessary if the hammer is too far from the gong (so that the gong is then too quiet) or too close to it (so that the gong »buzzes«).
  • Page 18 Technical specifications Due to the fact that every place on earth has a different gravitation, a clock that runs +/- 0 sec in Munich/Germany will gain or loose time if it is located somewhere else. As an example see Secunda Sonata – Cal. 2015 the list below: •...

  • Page 19: Troja Sonata M

    Press and hold the button If you start up the Troja Sonata M (connect it to the power supply) for the first time at 8.00 a.m., for example, the watch winder begins moving at 8.00 a.m. every day. From this point on, the watch winder units will start from 8 a.m. till 12 p.m. every day so then have they a stationary phase lasting 10 hours.

  • Page 20: Troja Opus Temporis

    Troja Opus Temporis SATTLER- PRECISION PENDULUM CLOCK CALIBRE 2050 Precision pendulum clock with moonphase, strike train, perpetual calendar, extendible watch winder and safe Thank you very much for your confidence. Your decision to purchase the precision pendulum clock with seconds’ pendulum shows that you belong to the very small circle of special connoisseurs of highest mechanical clock making art.

  • Page 21: Assembly Instruction

    Assembly instruction for the Troja Opus Temporis The Troja Opus Temporis will be shipped in one box Installation of the Troja Opus Temporis Place the safe at the final position 1. Unpacking the case top The safe can be fixed at the wall or floor. Check for wiring in the wall or floor. To use the...
  • Page 22 How to fit in the movement Caution! With the clock, there is a protecting cover that has to be laid inside the bottom of the Put the movement on the two brackets and screw it down with the two hexagon screws through case! The cover has to be used, to avoid damages of the case! Please remove the lower movement pillars.
  • Page 23 How to set the time Adjust all indications (date, day, moon phase) to the previous day and then turn hands with the crank over 24°° o´clock (midnight), allow striking mechanism to chime, calendar indicators Caution! will step forward, and set actual time. Do not adjust the hands by hand! Information: By using the pushers, the movement does not consider the different Connect the crank with the square behind the dial at 2 o´clock.
  • Page 24 The accessory box: How to correct deviations of 1 - 2 seconds from standard time: You can correct deviations of 1 - 2 seconds from standard time with the aid of the two In the bottom of the case you find the accessories as shown in the picture below. stainless steel weights also enclosed in the case.
  • Page 25 • pendulum rod of heat treated super invar If you start up the Troja Opus Temporis M (connect it to the power supply) for the first time at • pendulum weight turned of solid brass, nickel-plated 8.00 a.m., for example, the watch winder begins moving at 8.00 a.m.

  • Page 26: Fingerprintreader

    Maintenance and FAQ’s You will find the manual for the fingerprint reader at page 58 See page 74 The software Troja Opus Temporis How to use the software is described in chapter »Manual Technical data for software smart interface« see page 52...
  • Page 27 “ES_RO10_022” network in the WIFI settings for your device. The network name is made up as follows: ES_watch winder short name_serial number Watch winder short names: Troja 16 M ES_TROJA _ (serial number*) Troja Lunaris M ES _TROJA _ (serial number*)
  • Page 28 This can be reactivated after a brief interruption in voltage (disconnect and reconnect the power pack). Open, the laterally extendable watch winders units of the Troja models can be opened via WIFI here. Data: With this button, the settings are transferred to the watch winder and saved.
  • Page 29 Setting the Rotalis by using a practical example: Space for notes Activate the »Database« field; the keyboard for your smartphone or tablet PC is shown automatically. Enter the first three letters of the desired watch brand, e.g. ERW, the automatic sort function is started and all watches beginning with the relevant letters are listed.
  • Page 30 The watch winders and their components should only be installed by qualified personnel. Assign Security Medium = MkM kOK If you have any questions in this regard, please contact your specialist retailer or Erwin Sattler security level Medium 4 digit PIN-Code directly.
  • Page 31 4. Delete userfingers Detailed description Enter the program mode by scanning the masterfinger 1. Masterfinger enrollment • Red and green LED are on for a short time After activating the device for the first time or after reset to default settings, a masterfingers Press the button »D«...
  • Page 32 7. Change of relay circuit time 11. Check if an ID is already assigned Enter the program mode by scanning the masterfinger Press button »OK« Press the button »RT« on the remote control Enter the ID to be checked Enter the relay circuit time in seconds (1 to 65 seconds) by using the numbers Press button »OK«...

  • Page 33: Space For Your Notes

    Space for your notes Person (Name) Finger...
  • Page 34 THE PHASES OF THE MOON THE MOON 2016 - 2021 The moon circles the earth at a distance of 384.405 km and its diameter is 3.476 km. The moon’s volume is 50 times less that of the earths. The gravitational pull is significantly less than that of the earths and all weights on the moon are 6 times lighter.
  • Page 35 The safe Assembly and operating instructions for a free-standing safe from the »MÜNCHEN« series SAFE DEPOSIT SYSTEM Special edition Erwin Sattler (Euro/VdS Category l) German test institute for fire protection and security]) VdS-resitance unit 1 Insurance cover for private use up to €65,000.00* Insurance cover for commercial use up to €20,000.00*...
  • Page 36 1. Open and locking What if..Open: ...you hear a long beep after your combination last digit and the lock does not open? • Enter code (factory code = 1-2-3-4-5-6), unlock the You entered a not valid code. Repeat the operation, but pay attention for enter the right code. door and open it.
  • Page 37 5. Delete the secondary code Safe deposit system special edition Erwin Sattler Press and hold key »3« until double signal. The light remains on during the following actions. • Enter main code The secondray code is deleted. Security features VdS-resistance unit I in acc. with EN 1143-1. Defined protection against burglary with 30/50 RU against attacks by burglary tools with a mechanical and thermal effect.
  • Page 38 Care and Maintenance: Space for your notes The following maintenance tips will ensure that you enjoy your Troja for many years. We therefore advise you never to keep the clock case open over a long per iod of time, in order to prevent dust from depositing on the clockwork.
  • Page 39 ERWIN SATTLER GmbH & Co. KG Großuhrenmanufaktur Lohenstr. 6 · D-82166 Gräfelfing / Germany Tel. +49(0) 89 / 8955806-0 · Fax +49 (0) 89 / 8955806-28 e-mail: info@erwinsattler.de www.erwinsattler.de...

Table of Contents