Advertisement

User Manual
1
1
T108

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the T108 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for TIFGALOP T108

  • Page 1 User Manual T108...
  • Page 2 4.Prohibition of unauthorized modification of vehicles. 5.Please wear a safety helmet when riding and pay attention to safety! If you have any questions, you can consult us through the contact information below! What app : +86 13122291009 Reception email: Tifgalop@163.com...
  • Page 3: Folding Instructions

    Folding instructions 1. Pull the safety button 2. Step on the folding button with your foot and raise the handlebar 3. Close the handles on both sides, and then tighten the screws in the middle...
  • Page 5 Instrument and function introduction switch state...
  • Page 6: Parameter Setting

    1.Buttons There are two buttons on the display panel, namely power button / boot button and function button / mode mutton 2.Use Long press to turn on the power, the battery power and speed are displayed instantaneously according to the running status of the scooter, and the single mileage and cumulative mileage in the display are displayed according to the selected function.
  • Page 7 displayed, and then short press function key, P2, P3, P4, P5, P6, P7 will be displayed in turn; And they respectively indicated : P0: the wheel diameter setting; P1:the underpressure point setting; P2: the magnetic pole logarithm setting; P3: the speed measurement signal selection setting; P4:KM or MILE selection setting;...
  • Page 8: Fault Display

    the motor will be displayed,. You can press function button to increase 1 or you can press power button to subtract 1;  When P3 is displayed, short press power button, it will display 0 or 1; it indicates the speed measurement signal selection setting. When 0 is displayed (0 is generally selected), it indicates that the motor Hall signal is selected for speed measurement.
  • Page 9: Check Before Riding

    Check before riding 1. The saddle must be adjusted in the correct position and the bolts must be locked. 2. The indicator is correct, the lamp and horn work normal. 3. The brake lever must be flexible and reliable, and the motor can be powered off when braking.
  • Page 10: Safety Instructions

    Safety instructions 1. This product is limited to one person, do not carry other people at the same time. 2. It’s better to wear safety helmets and other protective equipment when riding this product, pay attention to riding safety. 3. Please practice in the flat and wide outdoor place with low traffic flow first, and then drive on the road after you are proficient in the product.
  • Page 11 Regular Inspection & Maintenance A: Check S: Adjust D: Replace L: Lubricate T: Tighten Inspection Items 60 days 180days 360days Whether the handlebar rotates and whether the steering parts are loose or worn Whether the tire is properly inflated and the tire is worn Front and rear axle gears, wheel axles are deformed or worn...
  • Page 12 Common Faults & Troubleshooting Methods Specific failure Cause of issue Solution conditions The anti-theft device or key lock is Replace the anti-theft display damaged device or key lock panel cannot The battery voltage is too low Fully charge the battery be turned on Blown fuse Replace fuse...
  • Page 13: After-Sales Service

    After-sales service Part Name Service Term Warranty Approach Motor 6 months Failure in normal use 1 year warranty for non-human damage Battery 6 months Failure in normal use Normal attenuation is not covered by warranty Instrument 6 months Quality issues 1 year warranty for accelerator non-human damage...
  • Page 14 What is not covered by the warranty The warranty period has expired or no car purchase certificate Commercial rental cars are not warranted The gifts are not covered by the warranty Unauthorized modification, damage caused by replacement parts The consumables of consumables are not guaranteed after one month, and if the consumables are damaged and are not replaced in time, the related parts will be damaged.

Table of Contents

Save PDF