NightRider NSB-BAR17AB Manual

Thank you for purchasing genuine NightRider™ LEDS.
This 17" Dual Colour (Amber/Blue) Beacon is SAE J845 Class 1 certified. Choose from 26 flashing patterns in Amber
only, Blue only, or Amber/Blue alternating. Beacon has memory function and will start up again on the last pattern used.
Be visible, be safe.
AMBER
FLASH PATTERNS
1 Single (ECE R65)
2 Single - Slow
3 Double (ECE R65/SAE)
4 Triple
5 Quad (ECE R65)
6 Octa
7 Twelve
8 Half/Half-Octa
9 Cross Octa
10 One - One Single
11 One - One Octa
12 CW Triple
13 CCW Triple
CW: Clockwise / CCW: Counterclockwise
Installation Options:
QUICK MAGNETIC MOUNT:
4 strong magnetic feet
with suction cups
FIXED MOUNT:
Peel off or cut a hole into sticker cov-
ering the bottom of the magnetic foot,
exposing the bolt. Remove bolts and all
4 magnetic feet.
NightRider™ LEDS takes no responsibility for incorrect installation and/or damages related. This guide is for reference purposes only. If unsure about your electrical system, contact your dealer or qualified professional
automotive/equipment technician. It is the vehicle operator's responsibility to ensure all product installations are properly, safely and legally installed in accordance to regional regulations of use.
PART# NSB-BAR17AB
17" AMBER/BLUE BEACON
BLUE
14 CW - Rotation
15 CCW Rotation
16 CW Constant Flash
17 CCW Constant Flash
18 CW Single
19 CCW Single
20 CW-CCW Constant Flash
21 Double - Rotation
22 All Quick - Half Quad
23 All Quick - Single - Fast Quad
24 Left Steady -Right Single
25 Right Steady - Left Single
26 Steady On
Please note that it is not recommended to use mag-
netic mounting of warning devices on fast moving
vehicles, use fixed mount option in that case. Usage
is at sole risk and responsibility of the user.
Remove the brown backing from the
foam gasket and then stick the gasket
to the bottom of the beacon.
www.nightriderleds.com
FEATURES:
• 144 x High Power 1.5W Epistar LEDs
• Colour: Amber / Blue
• 26 Flash Patterns
• IP67 certified - weatherproof & vibration resistant
• SAE J845 Class 1 (Amber/Blue) certified
• CISPR 25 Class 3
• Reverse Polarity Protection
• Size: 436mm (L) x 216mm (W) x 60mm (H)
• Memory function
• Operating Range: 12V or 24V
• Installation: Magnetic or Direct Mount (Hardware included)
Selection of Flashing Pattern / Colour:
- Press down selection switch for less than one second
on/off
to go to the next flashing pattern.
- Press down selection switch for 1-3 seconds
to go back to the previous pattern.
- Press down selection switch for 3-5 seconds to change
colour, press once more for 3-5 seconds to for alternating
colours, press for 3-5 seconds again for initial colour.
- Press down selection switch for more than 5 seconds to
Pattern/Colour
reduce power output to 50%, press down for more than
Selection Switch
5 seconds again to return to high power output.
on/off
NSB-WSMP
When using NightRider™ Gen2 Actuator Switch:
Gen2 Actuator Switch
Part # NSB-WSMP
WHITE: Pattern Select
RED: Positive
BLACK: Ground
Insert and fasten a threaded stud into
each of the 4 tapped holes where the
magnetic feet used to be.
SAE J845 Class 1
CISPR 25 Class 3
NightRider Gen2
Actuator Switch for
hardwiring option.
WIRING
Beacon
Part # NSB-BAR17AB
YELLOW: Pattern Select
RED: Positive
BLACK: Ground
Once all four bolts are safely secured in the beacon
and gasket is attached, install beacon onto desired
surface. We recommend applying some blue
threadlocker to secure your beacon light.