Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Excalibur Water Systems SMART PURIFIER PLUS
- Page 1 SMART PURIFIER™ PLUS REVERSE OSMOSIS SYSTEM...
-
Page 2: Table Of Contents
Product Introduction........................4 Reverse Osmosis (RO) Faucet Modes………………………..............4 Guide to Display Panel and Buttons on Your RO Filtration Unit…………………………………………...…..…4 Guide to Ports…………………………………………………………………………………………………………………..………6 Specifications…………………………………………………………………………………………………………………..……….6 Parts List............................7 Installation Instructions........................8 Before Installation........................8 Required Tools……………………………………………………………………………………………………………………..……8 Installation Diagram............................8 How to Drill a Hole in Your Sink or Countertop (Optional) …………………………….…......8 Installation Steps...........................9 Step 1: Connect Tubing to the Four Water Ports on the RO Filtration Unit…………………………..….9 How to Use the Quick-Connect Fittings……………………………………………………………………………....9... - Page 3 Please read and save these instructions. This system has been certified by IAPMO R&T against NSF/ANSI 58 for material safety, structural integrity and TDS reduction, NSF/ANSI 372 standard for Lead Free compliance. Substance Influent challenge Maximum permissible product concentration (mg/L) water concentration 750±40MG/L 187MG/L...
-
Page 4: Product Introduction
This is equipped with two , high-capacity water filters housed in an Smart Purifier PLUS cutting-edge under-cabinet filtration unit, as well as a separate smart faucet for dispensing the filtered/purified water. Both the filtration unit and the smart faucet feature digital displays for your convenience. -
Page 5: Reverse Osmosis (Ro) Faucet Modes
Purified Water indicator • The digital readout indicates in real time the quantity of TDS (“Total Dissolved Solids,” including all minerals such as sodium, calcium, magnesium, etc.) in the purified water, measured as mg per liter. This value is updated every 10 seconds. •... -
Page 6: Guide To Ports
display indicates the approximate filter life remaining (where fewer bars lit indicates less time remaining before the filter needs to be replaced). • After changing a filter, the filter’s corresponding display indicator should be reset. To do so, press and hold the Reset button for 3 seconds to enter filter reset mode, then tap the Select button as needed to highlight the relevant filter’s indicator. - Page 7 Input 110-240 V AC Power Specification Output 24 V DC Rated Frequency 100-240 V ~-50/60 Hz Max Daily Production Rate 1000 GPD Note: if you are using well water as the source, please ensure that the feed water has passed through a pre-filtration system.
-
Page 8: Parts List
(red) x1 3/8" Pressure Reducing Valve --> 40 PSI x1 3/8" Leak Detect x1... -
Page 9: Installation Instructions
Installation Instructions Before Installation Required Tools: • Variable speed drill • Screwdriver Adjustable wrench, • pliers • Utility knife or scissors Flashlight • • Towel • Drill bit 1/4” How to drill a hole in your sink or countertop (optional): NOTE: Confirm if there is an existing hole available to install the RO faucet. -
Page 10: Installation Steps
Installation Steps: Step 1: Connect tubing to the four water ports on the RO filtration unit a. Prepare the ports There are four ports at the bottom back of the filtration system unit. • First, remove the blue lock clip from each port by pulling the clip straight up. Then, remove the white connector from each port by pulling the •... -
Page 11: Step 2: Prepare The Filter Cartridges
Step 2: Prepare the filter cartridges a. Remove the front cover of the RO filtration unit. b. Twist the end of the top filter 90 degrees counterclockwise and pull the filter out of the unit. c. Remove the rubber band from the top of the filter. d. -
Page 12: Step 5: Install The Drain Saddle And Drain Water Tubing
NOTE: An extra adapter nut is included on the feed water adapter allowing it to attach to either a 3/8” or 1/2” feed plumbing line. d. Unscrew the 3/8” lock nut from the port that protrudes from the side of the feed water adapter. e. -
Page 13: Product Maintenance
Please contact us if the system cannot be powered on, and we will help determine the source of the problem. e. After the first power-up, the system will beep and then start an automatic 18-second flush. After the initial 18-second flush is complete, turn on the tap and let the system continue flushing for an additional 30 minutes to wash the filter cartridge. -
Page 14: Flushing The Filter After Replacement
a. Remove the front cover of the RO filtration unit. b. Twist the filter that needs to be replaced counterclockwise until the triangle symbol on the filter is aligned with the “unlocked” symbol on the filter housing. c. Remove the old filter by pulling it straight out. Note that a small amount of residual water will flow out when the old filter is removed. -
Page 15: Troubleshooting
When cleaning, do not pour other liquids into the filter so as not to risk damaging the filter system. Keep the wastewater pipe unobstructed to avoid damage to the filter or internal components. When the drainpipe is blocked, do not use the system (and please turn off the power) to avoid wastewater from flooding the floor. - Page 16 feed water passes through a pre-filtration system. Otherwise, large particles in the well water may clog the filter and shorten the filter life. High TDS in Filtered Water The system will provide a 90% TDS (Total Dissolved Solids) rejection rate (tested under standard laboratory conditions) after full flushing when working properly.
- Page 17 Warranty ~ Working Procedures If during the suitable warranty period, a part is defective, then Excalibur Water Systems will repair or replace that part at no charge to the original owner, with the exception of charges for nominal shipping, service and/or installation.
Need help?
Do you have a question about the SMART PURIFIER PLUS and is the answer not in the manual?
Questions and answers