Page 1
Electric Instantaneous Water Heater Operation and Installation Instructions Model No.: Smarta 11 series ----------------------------------------------------------- Keep this Instructions Manual in a safe place once your unit is installed. You may need to refer to it for general instructions or future maintenance.
[Smarta 11 series] Please read and follow the installation and operation instructions carefully, to ensure the long life and reliable operation of this appliance. CONTENTS Important Safety Instructions---------------------------------------------------------------------------page 2 Product Features --------------------------------------------------------------------------------------------page 3 Electrical Diagram ------------------------------------------------------------------------------------------page 4 Technical Data -----------------------------------------------------------------------------------------------page 5...
[Smarta 11 series] Attention! This is not a do-it-yourself project. Failure to have this appliance installed by a licensed plumber and electrician will void all warranties. Under no circumstances should you attempt to install, repair, or disassemble the electric instantaneous water heater without first shutting off all power to the unit directly at the circuit breaker box.
[Smarta 11 series] 11. The shower head should be cleaned and descaled periodically. 12. The water relief valve should work periodically to remove calcium carbonate deposits. 13. The drainpipe which connected to the water relief valve should be installed continuous downward in frostless environment.
[Smarta 11 series] ■Technical Data Model Smarta 11 series 220 – 240 V Rated Voltage Rated Power 11 kw Rated Current 47.9 A Rated Pressure 0.6 MPa Efficiency t=25C 6.3 L/min Safety class IP25 30 – 55 °C Temp. setting arrange Overheat protection 62 °C...
[Smarta 11 series] ■Installation Guideline The installation must be in compliance with the National Electrical Code, your local electrical and plumbing codes. 1. Make sure the appliance is intact, and the fittings are complete. 2. Please make sure the main power supply, water pressure, grounding condition, ammeter and wire reach the standard of installation requirement.
Page 8
[Smarta 11 series] Fig 2 Remove screw which fixed the front case and back case. Fig 3 Open the front case, then connect power cable to the terminal blocks with L1, L2 and E in pointed position. 7 / 12...
Page 9
[Smarta 11 series] Fig 4 Fix the front cover on the appliance, before that, please plug in the flat cable of display board to the main power board, then nail the screws to fix the front cover. Fig 5 Use the cardboard to make 3 mark for punching, then drill 3 holes with 6mm diameter, nail in the wall.
Page 10
[Smarta 11 series] Fig 6 Fix the application on the wall. Fig 7 Connect the water pipe to the water inlet and water outlet connections, please remember to install the rubber seal ring. outlet Inlet 9 / 12...
[Smarta 11 series] ●Water connections 1, All water pipe must comply with national and applicable state and local water pipe codes. 2, The unit should be connected directly to the main water supply. Flush pipe with water to remove any debris or loose particles.
[Smarta 11 series] Please run the water through for a few seconds to let the temperature settle down. Please check hot water with hand before you are taking a shower. ⚫ If the unit will not be used in winter, drain out water completely so that the heater will not be frozen.
[Smarta 11 series] 8. should only be performed by qualified electrician. The person who initially installed the unit is the best one to contact for help. ■Normal Maintenance Note: Do not attempt to repair this water heater yourself. Call a service person for assistance.
Page 16
[Smarta 11 series] يبيئةيخاليةيمنيالصقيع . ي يجبيأنييتميتر كيبيأنبوبيالرصفيالمتصليبصماميتخفيفيالمياهيبشكليمستمريألسفليف ي يجبينز عي ر أسيالرشيبانتظام . ي . يجب عدم توصيل مدخل الماء لهذا الجهاز بمدخل الماء الذي يتم الحصول عليه من أي نظام تسخي ز مياه آخر مميزات المنتج ▪ يخزن...
Page 20
[Smarta 11 series] طريقة التثبيت ▪ ● Fixed installation on the wall Locate an appropriate place on a section of wall as above mentioned. .ابحث عن الموقع المناسب على جزء من الحائط كما هو موضح أعاله Fig 1 Front and back of the appliance.
Page 21
[Smarta 11 series] Fig 3 Open the front case, then connect power cable to the terminal blocks with L1, L2 and E in pointed position. افتح العلبة األمامية ، ثم قم بتوصيل كبل الطاقة بالكتل الطرفية Fig 4 Fix the front cover on the appliance, before that, please plug in the flat cable of display board to the main power board, then nail the screws to fix the front cover.
Page 22
[Smarta 11 series] Fig 5 Use the cardboard to make 3 mark for punching, then drill 3 holes with 6mm diameter, nail in the wall. مار في الحائط مم ، مس فتحات بقطر عالمات لللكم ، ثم قم بحفر استخدم الورق المقوى لعمل...
Page 23
[Smarta 11 series] Fig 7 Connect the water pipe to the water inlet and water outlet connections, please remember to install the rubber seal ring. حلقة المطاطية ال قم بتوصيل أنبوب الماء بوصالت مدخل المياه ومخرج المياه ، يرجى تذكر تثبيت...