Instruction Manual Hose Reels INDEX 1. INTRODUCTION ..................28 1.1 Description........................28 1.2 Remaining risks and safety stickers..................29 1.3 Non-admitted uses ......................29 2. TECHNICAL PARTICULARS ..............30 2.1 Overall dimensions and weights ..................30 2.2 Noise..........................34 3. DELIVERY, HANDLING AND INSTALLATION .........34 3.1 Delivery ..........................34 3.2 Handling.
Page 4
Instruction Manual Hose Reels SYMBOLS Below we give a short legend indicating the symbols used (the symbols given are the ones most used in this booklet; the remaining symbols are anyhow easy to understand). DANGER draws attention to situations or problems that may jeopardize the safety of persons due to injury or the risk of death.
Painted Stainless steel steel Mod. Mod. Mod. Mod. • Hose reel Mod. 35810-35815-35812: 36485 37147 36490 37490 this is an automatic hose reel whit external 36480 37148 plastic cabinet; that equipment is suitable for air and water. Twin Springs...
Instruction Manual Hose Reels 1.2 REMAINING RISKS AND SAFETY STICKERS. Figure 1 shows the areas at greater risk, with the related stickers showing the remaining risk and the main components comprising the machine, according to the instructions given below: Main components and risks A.
Instruction Manual Hose Reels 2. TECHNICAL PARTICULARS Below we give the essential technical particulars of the models. 2.1 OVERALL DIMENSIONS AND WEIGHTS Standard Series Bore of Max Hose Spool Swivel Connections Sizes Weight Model pressure swivel joint Hose leght width Bracket on In - Out Ø...
Page 8
Instruction Manual Hose Reels Enclosed Series Bore of Max Hose Spool Swivel Connections Sizes Weight Model pressure swivel joint Hose leght width Bracket on In - Out Ø request 35300 M1/2” - F1/2” 1/2” 39507 130 550 450 35400 M1/2” - F1/2” 1/2”...
Page 9
Instruction Manual Hose Reels Mechanical Series Bore of Max Hose Spool Swivel Connections Sizes Weight Model pressure swivel joint Hose leght width Bracket on In - Out Ø request 36490 M1/2” - F1/2” 1/2” 590 650 590 37490 M1/2” - F1/2” 1/2”...
Instruction Manual Hose Reels 2.2 NOISE. The level of noise emitted (level of sound pressure) is extremely low (< 70 dBA). It is anyhow for the employer to evaluate the level of exposure to noise for each single worker.. 3. DELIVERY, HANDLING AND INSTALLATION 3.1 DELIVERY The operator must: •...
Instruction Manual Hose Reels 3.3.1 INSTALLATION HOSE REEL The operator must keep to the following rules: Phase 1 the hose reel are to be mounted on the wall with xing reinforcement dowel (Ø 12 mm.) and connecting of 70 mm. at least. If the plate is present you have to put the plate between the hose reels and the wall.
Instruction Manual Hose Reels 4. SAFETY WARNINGS 4.1 WORK ENVIRONMENT Never approach the equipment with naked ames or the like. Never use the equipment in places where there is a risk of explosion and re. We recommend to install the hose reel at adequate height (at least 2,5 m). Check in advance the solidity of the wall where the equipment is xed (avoid perforated brick).
Instruction Manual Hose Reels 5. GENERAL RULES FOR OPERATION 5.1 PRELIMINARY CHECKS. Effettuare sempre i seguenti controlli: Description • 1. • Check the connection the hose to the wall • 2. • Presence of cable (high tension) high voltage • 3. •...
Instruction Manual Hose Reels 6. MAINTENANCE Do not carry out any maintenance operation when the spring of the equipment is in tension or when the pressu- re is present in the hose of connection. We recommend to discharge the residual pressure in the hose and to place the hose in the initial position (rewinding it in the hose reel).
Instruction Manual Hose Reels Phase 2 put the hose through the guide rollers, drawing your attention to roll the hose in the sense of the curved tongue. Connect the hose to the adaptor placed in the reel then tighten it with suitable key.
Instruction Manual Hose Reels 6.1.2 DISASSEMBLY/REASSEMBLING HOSE-SPRING IN THE SYSTEMS WITH CABINET. 6.1.2.1 DISASSEMBLY Phase 1 the casing (part.2) are disassembled, unscrewing the screws (part.1), the lling hose (part.3), the swivel joint (part.4) and the hose bumper (part.6). Phase 2 unscrew the 4 screws (part.1) at the opposite side of the small casing.
Instruction Manual Hose Reels 6.1.2.3 REPLACE OF THE SPRING Phase 1 put the hex. wrench (part.A) in the bore (part.B and C) and unscrew the hex. socket-screws. Then remove all the kit (part.1) and replace it with one equipped with new spring. The old spring cannot be repaired.
Instruction Manual Hose Reels 6.1.3 CHOICE OF THE HOSE Below we show the rules for the correct choice of the hose in relation to material used (see the chapter 2). 6.1.3.1 GREASE SAE 100 R2T Technical Particulars: • Tube: black, oil, petrol, hydraulic uids resistant synthetic rubber.
Instruction Manual Hose Reels 7. SPARE PARTS Enclosed with this booklet are tables making it possible to request spare parts for our machines from our technical service. Below we give an example of an enquiry. It is recommended to give all the data requested Firm Street...
Instruction Manual Hose Reels 9. ACCESSORIES A swivel bracket can be supplied on request to make easy the use of the hose reel. In the Data table we give for every model of hose reel the code of the swivel bracket. For the hose reels (made with steel) heavy series remove the plate of xing and replace with system jointed.