AAG Linx Spinner Quick Start Manual

Version: A/03
Product Features
Technical specification
Working voltage: DC 3.7V
1. To wake the sensor up for the first time, press the reset button. The screen will come on after a few seconds.
Radio frequency: 433.05~434.79MHz
Until this is done, the sensor will generally not operate.
Safety code (50 million times without repeat, high security)
Warning
2. Adjusting Sun settings
1, Stable performance, wireless remote control, solar powered, Type-C charging.
Warning: In most cases it is not recommended to use the sun settings, as automated and unattended
2, Check the voltage once a day. When the voltage is lower than 2.7V, a small battery icon is displayed to indicate low voltage.
3, The sensor can be fixed to the wall with two screws.
operation of awnings can lead to possibly undesired or dangerous operation.
4, Adjustable wind intensity range: 0~180Km/h; sunlight intensity range: 0~100Klux.
To ignore sun operation, make sure sun settings are set to "0.0"
5, Once the wind intensity exceeds the setting level, the sensor will send signals to the motor automatically to close the awning
1. Tap 'M" to bring up display if it is blank.
within 3S.
2. Press and hold "M" for about 2 seconds and the digits will start flashing along with the sun symbol.
6, When the sunlight intensity exceeds the setting level continuously more than 2 minutes, the sensor will send signals to open
the awning and will not detect the sunlight intensity within 15 minutes; when the sunlight intensity hasn't less than the setting
3. Use the "UP" button to count up and the "A" button to count down. Holding either button will cause
level continuously more than 15 minutes, the sensor will send signals to close the awning.
the unit to count faster.
7, The LCD display screen will be ON for 30S. The LCD screen will turn off after 30S without any press while the programming
4. Each full digit is 1000 Lux. You can set up to 100,000 Lux.
keeps running at the background; Press any button(except reset button) to turn on the LCD screen for 30S.
3. Adjusting Wind settings
Matchable Motors And Emitters
1. Tap 'M" to bring up display if it is blank.
Uni-directional mode
2. Press and hold "M" for about 2 seconds and the digits will start flashing along with the sun symbol.
3. Tap "M" again and the Flag (wind symbol) will appear, and the digits will flash.
4. Use the "UP" button to count up and the "A" button to count down. Holding down either button will
cause the unit to count faster in that direction.
DC1600
5. The numbers in the display are the actual wind speed you are setting, from 0.1 kmh to 180 kmh.
For a folding arm awning, a speed of between 15 – 25 kmh would be normal. Higher settings can be used
for Zip systems.
DD118B
NOTE: once the wind has triggered the awning to retract, a zip system or guided awning will not react to
the sensor again for 8 minutes, but the remote will still work.
For folding arm awnings, neither the sensor nor the remote will work for 8 minutes.
sales@australianawning.group
Linx® Spinner Sun/Wind Sensor
Note: 1,Pls make sure that the wind-sun sensor have been paired to the receiver.
2,pls make sure when press UP button, the awning will be retracted.
Menu
UP
Working temperature：-10℃~+60℃
Radio range: outdoor
R-type tubular motor
E/ED-type tubular motor
1300 791 010
LCD
Adjust
P2
Reset
Working current: ＜20mA
meters, indoor＞40 meters
＞100
Bi-directional mode
DD1600H
DD118B
www.australianawning.group linxautomation.com.au
k l u x km/h
SUN: WIND:
LCD
Standard tubular motor
DD1538H or External
Receiver (Refer to
"Matchable Receiver")