Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for LADE mini
- Page 1 LADEmini Installation Download full manual lade.de/lademini-manual-en...
-
Page 2: Scope Of Delivery
Scope of delivery Not to scale LADEmini Wallbox LADEmini Wallbox Cable gland with bend protection Charging cable (11 or 22 kW) 3-wire Wago clamp Adapter board with RJ45 socket and ribbon cable 2-wire Wago clamp Earth cable Adapter board with IDC connector and ribbon cable Nut M5 Screw for adapter board Screw sleeve... - Page 3 LADEgenius LADEgenius 12 x 2-pole connector 3-pole connector 4-pole connector 4-pole connector large 24 V top-hat rail power supply unit Suction cup for removing the glass pane of the LADEmini wallbox (included with LADEgenius) Optional Metal holder Jumper (for charging points with 22 kW charging capacity) RJ45 connector (when using installation cable between IO module and adapter board)
- Page 4 Modules max. 400 m max. 400 m LADEgenius / LADEgenius RT • Installed on top-hat rail near the house connection. • Controls up to 96 charging points and other consumers. • Measures the current at the house connection (LADEgenius RT). •...
- Page 5 LADEmini Cabinet Example for 4 charging points Contains power electronics for one to four charging points (pre-wired): • IO Module • MID meter • RCD type B • Contactor (2 x 2-pole or 1 x 4-pole) • Circuit Breaker (optional) LADEmini Wallbox Wallbox at the parking space with charging cable, display and LED ring.
-
Page 6: Wiring Overview
Wiring – Overview Power supply line Data line Pre-wired Controls up to 16 IO Modules per channel 24 V voltage supply Main fuse house Current and connection voltage measurement RJ45 socket / Ethernet Internet access via LTE router / switch / LTE antenna Fuse... - Page 7 Cabinet Example for 2 charging points Schematic representation. Contains only components to which cables must be connected. Contactor #1 Contactor #2 Circuit breaker #1 Circuit breaker #2 If no circuit breaker is If no circuit breaker is installed: RCD switch installed: RCD switch...
- Page 8 1 – Installing LADEgenius • Mount LADEgenius on top-hat rail • Attach current transformers to main line and connect them to LADEgenius with respect to the correct phases • Connect voltage measurement with respect to the correct phases. • Connect LADEgenius to router or switch via Ethernet; alternatively: install LTE antenna •...
- Page 9 max. 16 A Up to 16 IO Modules / charg- ing points in series, distrib- uted over several cabinets...
- Page 10 2 – Connect Cabinet Hardware-Version 1 IO Module with 8 DIP switches Requirements: • Cabinet is fixed to the wall • Data and supply lines are laid 1. Connect the data bus coming from 2. Connect the data line going 3.
- Page 11 5. If applicable, switch on 6. Connect the supply line to the first 7. Connect the supply line going terminating resistor. circtuit breaker from the left on the towards the charger to the input side. corresponding contactor (1 x 4-pole or 2 x 2-pole). If no circuit breaker has been installed, connect the supply line to the RCD on the input side.
- Page 12 2 – Connect Cabinet Hardware-Version 2 IO Module with rotary switch Requirements: • Cabinet is fixed to the wall • Data and supply lines are laid 1. Connect the data bus coming from 2. Connect the data line going 3. Adjust hardware settings. LADEgenius to the bottom of the IO module.
- Page 13 5. If applicable, switch on 6. Connect the supply line to the first 7. Connect the supply line going terminating resistor. circtuit breaker from the left on the towards the charger to the input side. corresponding contactor (1 x 4-pole or 2 x 2-pole). If no circuit breaker has been installed, connect the supply line to the RCD on the input side.
-
Page 14: Install Wallbox
3 – Install wallbox Requirements: • Metal holder [C5] and cable junction box [C4] are installed • Data and supply lines have been laid The glass pane is attached to the housing with magnets. Use the enclosed suction cup to remove the pane. - Page 15 1. Insert the data line from the rear, top, right or left and connect it to the adapter board. Variant 1: Lay installation cable Variant 2: Plug pre-assembled on IDC connector, use colour patch cable into RJ45 socket coding A 2.
- Page 16 LADE GmbH Wilhelm-Maybach-Straße 11 55129 Mainz Germany partner@lade.de +49 6131 92 66 330 lade.de...
Need help?
Do you have a question about the mini and is the answer not in the manual?
Questions and answers