Summary of Contents for body Power ERG8000
- Page 1 ERG8000/ERG9080 DELUXE INDOOR CYCLE TRAINER WITH CURVE-CRANK TECHNOLOGY ® This product is intended for indoor, home use only and is not to be used in a commercial setting. OWNER’S MANUAL...
- Page 2 This page is left blank intentionally...
- Page 3 ARE NOT FOLLOWED. The diagram below highlights and reviews many of the important Safety and Warning labels also found on the unit. Please ensure any user of the unit familiarizes themselves with this Safety and Warning guidelines before use. ERG8000/ERG9080 Page 1...
-
Page 4: General Information
21717 Ferrero Parkway, Walnut, CA 91789 - 1 x Philips (”Crosshead”) Screw Driver Telephone: 1 (888) 266 - 6789 Fax: 1 (909) 598 - 6707 Weight Limit Email: info@bodyflexsports.com Your product is suitable for users weighing: 300 pounds or less ERG8000/ERG9080 Page 2... -
Page 5: Before Assembly
Ruler (with both Metric and English measurements) Use to measure the length or size of hardware including QTY: 1 bolts to ensure you are using the correct part. Adjustable or flat wrenches Use to securely install parts including nuts and bolts. QTY: 2 ERG8000/ERG9080 Page 3... -
Page 6: Part Listing
Nut (M10) Bolt (M8x16 mm) 39L/R Crank PU Washer 40L/R Pedal Tension Knob Bracket Screw (ST4.2x16 mm) Wave Washer (M17) Screw (ST4.2x19 mm) Washer (M5) 43L/R Left/Right Shroud Shroud Cover C Clip (D17) Allen Wrench Bearing (6004-2RS) Spanner ERG8000/ERG9080 Page 4... -
Page 7: Exploded View
: : Not all of the parts and hardware you see here will be used while you are assembling the machine because some of these items are already pre-installed. Please use this page only as a reference guide for parts and hardware. 42 42 89 41 A S6 B S13-S15 ERG8000/ERG9080 Page 5... -
Page 8: Hardware And Tool List
#33 Washer (M10) [7 pieces] [10 pieces] [1 piece] Pre-assembled [3 pieces] Nuts #76. Nylon Nut (M8) [3 pieces] Pre-assembled Others #34 Knob (M10x32mm) [1 piece] Tools (Included) #B Spanner #A Allen Wrench [1 piece] [1 piece] ERG8000/ERG9080 Page 6... -
Page 9: Assembly Step
Attach Right Pedal (No.40R) to Right Crank (No.39R). Turn the Right Pedal (No.40R) clockwise to lightly tighten it. Note: The Pedals (No.40L/R) are marked "L"and "R" for Left and Right. Make sure you attach the correct pedal to the corresponding crank. Front Roller ERG8000/ERG9080 Page 7... - Page 10 (No.69), 1 Bolt (No.84), 3 Spring washers (No.10) and 3 Washers #69 Bolt (M8x45 mm) (No.11). Then attach the Cover (No. 67) on the Handlebar (No.78) #10 Spring Washer (M8) [2 pieces] [3 pieces] (Figure B) #11 Washer (M8) #84 Bolt (M8x16 mm) [3 pieces] [1 piece] ERG8000/ERG9080 Page 8...
- Page 11 However, for your own safety, please make sure to read this entire Owner’s Manual which includes safety instructions and warnings, as well as any safety/warning labels affixed to the product before use. For your safety , please visually and functionally inspect and test the unit after assembly is complete. ERG8000/ERG9080 Page 9...
-
Page 12: Tension Adjustment
The Brake Handle (No.19) is an emergency brake. Use this safety feature in a situation when you would need to get off the bike or stop the bike’s flywheel. During exercise, press down firmly on the Brake Handle (No.19) to stop the bike immediately. ERG8000/ERG9080 Page 10... -
Page 13: Pedal Strap Adjustment
When the pedal is tight, press the buckle and pull the strap up to loosen the strap (Figure A). When the pedal is loose, press the buckle and pull the strap down to fasten the strap (Figure B). Figure B Figure A ERG8000/ERG9080 Page 11... -
Page 14: Seat And Handlebar Adjustment
C. To adjust the height of Handlebar (No.78), loosen and pull on the Knob (No.13), then slide the Handlebar Post (No.74) up or down to the desired height. Once adjusted, tighten the Knob (No.13) to secure the Handlebar Post (No.74) in place. ERG8000/ERG9080 Page 12... -
Page 15: Balance Adjustment
Foot Pads (No.3) until it sits level with the surface that the bike is When you have finished adjusting the Foot Pads (No.3), re-tight- en the Hexagonal Nut (No.2) by turning it counter-clockwise using Spanner (Tool B). If needed, repeat this process to adjust the remaining Foot Pads (No.3). ERG8000/ERG9080 Page 13... -
Page 16: How To Move The Bike
Handlebar (No.78), place one foot on the front base and tilt the bike towards you until the Transport Wheels (No.7) on the front base touch the ground. With the wheels on the ground, you can transport the bike to the desired location with ease. ERG8000/ERG9080 Page 14... -
Page 17: Safety And Maintenance
1 (888) 266-6789 or 1 (909) 598-9876, or mail in a written request to: Body Flex Sports, Inc. 21717 Ferrero Parkway Walnut, CA 91789 More detailed information about how to reach our CUSTOMER SUPPORT may be found on Page 2 of the Owner’s Manual under the “CUSTOMER SUPPORT” section. ERG8000/ERG9080 Page 15... -
Page 18: Warm-Up Instructions
Keep your left leg straight. 2. Return to the starting position slowly. 2. Gently pull your right leg toward your trunk without raising your upper body. Switch leg positions and repeat. ERG8000/ERG9080 Page 16... - Page 19 Repeat on the other leg. muscles in your left calf stretch. other. Switch leg positions and repeat. Reverse arm positions and ERG8000/ERG9080 Page 17...
- Page 20 THANK YOU FOR YOUR PURCHASE MODEL NO.: ERG8000/ERG9080 Please fill in the information below and keep this manual along with your sales receipt as proof of purchase. Serial Number : Date of Purchase : Retailer : Body Flex Sports, Inc.
Need help?
Do you have a question about the ERG8000 and is the answer not in the manual?
Questions and answers