Table of Contents
Advertisement
Quick Links
PRODUCT MANUAL
PEC 827E
120 VAC AC Distribution Shelf
6180498P (23" For Conduit), 6180529P (23" W/Outlets)
6180542P (19" For Conduit), 6180533P (19" W/Outlets)
This document issue 4ge is updated with OmniOn brand and contact information only, no other content change
from issue 4. Issue 4 release date: August 2007.
Page 1
© 2023 OmniOn Power Inc. All rights reserved.
827E AC Dist_MAN
Rev. 2.4
Advertisement
Table of Contents
Related Manuals for OmniOn Power PEC 827E
Summary of Contents for OmniOn Power PEC 827E
- Page 1 This document issue 4ge is updated with OmniOn brand and contact information only, no other content change from issue 4. Issue 4 release date: August 2007. Page 1 © 2023 OmniOn Power Inc. All rights reserved. 827E AC Dist_MAN Rev. 2.4...
-
Page 2: Table Of Contents
4: Initial Turn On and Acceptance Procedures ..........................15 4.1 General ................................................ 15 5: AC Distribution Panel Ratings ..............................15 Description Part Number T-Drawing for AC Distribution Shelf 4390670T Page 2 © 2023 OmniOn Power Inc. All rights reserved. 827E AC Dist_MAN Rev. 2.4... -
Page 3: Foreword
Fill in the part number, as it appears on the label, in the space below. PART NUMBER DATE CODE: SERIAL NUMBER ECN LEVEL: 860 _ _ _ _ P Page 3 © 2023 OmniOn Power Inc. All rights reserved. 827E AC Dist_MAN Rev. 2.4... -
Page 4: Warnings
California to cause cancer and birth defects or other reproductive harm. Wash hands after touching batteries. Page 4 © 2023 OmniOn Power Inc. All rights reserved. 827E AC Dist_MAN Rev. 2.4... -
Page 5: Cautions
Before performing any maintenance, ensure AC or DC power is not applied to the plant. Fuse holders, fuses, and circuit breakers are not to be loaded to more than 80 percent of their ampere rating. Page 5 © 2023 OmniOn Power Inc. All rights reserved. 827E AC Dist_MAN Rev. 2.4... -
Page 6: 1: Installer Information
1.3 Tools and Test Equipment Required for Installation and Acceptance Test Equipment Purpose Quantity Torque Wrench rated to 50 ft. pounds Torque connection points. Digital Meter Distribution verification Figure 1-1. AC Distribution Shelf (Front View) Page 6 © 2023 OmniOn Power Inc. All rights reserved. 827E AC Dist_MAN Rev. 2.4... -
Page 7: 2: Mechanical Installation
Installation is complete. Figure 2-2. AC Distribution Shelf – Open Front Access Cover Figure 2-1. AC Distribution Shelf (Rear View) Page 7 © 2023 OmniOn Power Inc. All rights reserved. 827E AC Dist_MAN Rev. 2.4... - Page 8 Figure 2-3. AC Wire Way from 827E Inverter Shelf to AC Distribution Panel Page 8 © 2023 OmniOn Power Inc. All rights reserved. 827E AC Dist_MAN Rev. 2.4...
-
Page 9: 3: Electrical Connections
Terminal Type Recommended Wire Size 6 AWG – 250 MCM Compression 6 AWG 6 AWG – 250 MCM 1/4" on 5/8” (Two Hole Lug) 6 AWG Page 9 © 2023 OmniOn Power Inc. All rights reserved. 827E AC Dist_MAN Rev. 2.4... - Page 10 Figure 3-1: 120 VAC From Inverter Shelf to AC Distribution Panel (Right Side) NEUTRAL LINE GROUND Figure 3-2: AC Distribution Shelf Input Connections Rear View (Unwired) Page 10 © 2023 OmniOn Power Inc. All rights reserved. 827E AC Dist_MAN Rev. 2.4...
- Page 11 Figure 3-3: AC Distribution Shelf Input Connections Front View (Fully wired) BUILDING GROUND Figure 3-4: Block AC Wiring diagram from the 827E Inverter shelves to the distribution shelf. Page 11 © 2023 OmniOn Power Inc. All rights reserved. 827E AC Dist_MAN Rev. 2.4...
-
Page 12: Load Connections
Figure 3-5: Ground, Load, Neutral Connections Loads are routed under the Neutral connection and out the rear of the AC Panel. Figure 3-6: Load Connections cable routing Page 12 © 2023 OmniOn Power Inc. All rights reserved. 827E AC Dist_MAN Rev. 2.4... -
Page 13: Load Connections (With Outlets)
Recommended Wire Size 2 –15 Amps per position 4 - 14 AWG Compression Dependant on load Ground Neutral Load Figure 3-7: Ground, Load, Neutral Connections (With Outlets) Page 13 © 2023 OmniOn Power Inc. All rights reserved. 827E AC Dist_MAN Rev. 2.4... -
Page 14: Frame Ground Connection
Frame ground. See Figure 3-8. Terminal Type Recommended Wire Size 1/4” on 5/8” Centers for Inserts As Required Frame Ground Connection Figure 3-8: GEC Ground Connection Page 14 © 2023 OmniOn Power Inc. All rights reserved. 827E AC Dist_MAN Rev. 2.4... -
Page 15: 4: Initial Turn On And Acceptance Procedures
15 Amps per circuit position 6180542P (19” For Conduit) 100 Amps 120VAC 70 Amps per circuit position 6180533P (19” W/Outlets) 100 Amps 120VAC 15 Amps per circuit position Page 15 © 2023 OmniOn Power Inc. All rights reserved. 827E AC Dist_MAN Rev. 2.4... - Page 16 – in whole or in parts – is forbidden without document and makes no warranty with respect to and prior written consent of OmniOn Power. This document assumes no liability as a result of any use of information does not convey license to any patent or any intellectual in this document.
Need help?
Do you have a question about the PEC 827E and is the answer not in the manual?
Questions and answers