Hansen Radar Outdoor Installation Instructions

Installation Instructions
Radar Outdoor
Safety notes
The electrical connection must be carried out by qualified electricians only.
Ÿ
The supply voltage must be switched off before carrying out any installation or
maintenance activities.
Only use original parts from the manufacturer for maintenance and repair.
Ÿ
The manufacturer accepts no liability for damage caused by improper use or
Ÿ
extreme external influences. These are for example:
Mistakes during transport and installation:
Ÿ
excessive bending, twisting or squeezing of the LEDs and connecting
wires, particularly due to improper use of sharp tools
damage due to improper transport or installation
tampering with the electric circuits
Environmental and natural influences:
overheating due to excessive ambient temperatures
chemical influences in the environment (e.g. sulphur)
dirt contamination
overvoltage due to lightning
Please keep these instructions with the documentation of your installation.
Intended use
1
The hansen Radar Outdoor is a semi-finished product which fulfills its final
Ÿ
function after further processing (e.g. installation) by the customer or third
parties.
The Radar Outdoor is designed for the illumination of channel letters, light
Ÿ
boxes and similar hollow bodies inside and outside dry rooms. In addition, it
can be operated "open", i.e. without protective enclosure inside dry rooms
when appropriate mechanical or electrical protection is provided.
Proper operation, storage and processing of the Radar Outdoor is only
Ÿ
ensured in still natural air, free of chemically reactive gases, vapours,
aerosols, liquids or solids, within the temperature range between -10 °C and
+50 °C, at humidity levels below dew point (no condensation), free of UV
radiation or ionizing radiation with wavelengths below 380 nm. Any use of
the product outdoors outside suitable hollow bodies or under water is not
permitted.
The intended use includes observance of the associated technical data
Ÿ
sheet, operating instructions and installation instructions.
Radar Outdoor and accessories
2
1
1 Radar Outdoor LEDs
Accessories (picture shows example):
Not included in the scope of delivery. Depends on the
order, quantity and scope (see delivery note).
2 LED converter (optional)
3 WAGO connectors (optional)
4 Insulating caps (optional)
3
4
Technical modifications reserved. Content is protected by copyright.
Page 1/2
Unpacking and checking the content
The packaging must be opened in such a way that the content
Ÿ
cannot be damaged. Particular care must be taken when
using sharp tools.
After unpacking, immediately check the content for damage
Ÿ
(e.g. transport damage) and compliance with the delivery
note.
Any defects or deficiencies must be notified to the supplier
Ÿ
(the company Hansen) immediately.
Rear side
Connecting cable
Fixing hole (ø 4.6 mm)
Installing the Radar Outdoor LEDs
The Radar Outdoor LEDs are usually mounted on the inside
Ÿ
rear wall of the illuminated body (e.g. light box) with the
LEDs/lenses facing towards the front.
The Radar Outdoor LEDs should be distributed as evenly as
Ÿ
possible inside the illuminated body. This can be ensured by
installing them at the spacing pre-determined by the length of
the connecting cables. If required, they can be installed at a
smaller spacing, which will create loops in the connecting
cables.
The Radar Outdoor LEDs can be fixed in two ways:
Ÿ
with double-sided adhesive tape or
with screws
Fixing with double-sided adhesive tape
Ÿ
The Radar Outdoor LEDs are provided with an adhesive pad
on the rear protected by a paper foil. Remove the protective
foil and place the LED on the desired spot. To ensure good
adhesion, press the LED onto the surface with moderate
finger pressure. Make sure not to place the finger onto the
LED/lens but onto any other part of the module.
Fixing with screws
Ÿ
Each Radar Outdoor LED can be fixed to the rear wall using a
screw. The adhesive tape provided on the rear can (with or
without the protective foil) remain on the module. For a
screwed connection, each Radar-LED is provided with a
4.6 mm fixing hole. Threaded bolts, chipboard screws, sheet
metal screws or self-tapping screws can be used. Make sure
to only hand-tighten the screws as firmer tightening may crack
the housing and damage the LED.
Hansen GmbH
Tel. +49 4843-2009 0 § info@hansen-led.de
Adhesive pad
Front side
LED
August 2021 M06e/08/2021
§ www.hansen-led.de