Related Manuals for DEVANTI H1107G
Summary of Contents for DEVANTI H1107G
- Page 1 INSTRUCTION MANUAL OUTDOOR PATIO HEATER FOR OUTDOOR USE ONLY ! PLEASE KEEP THE MANUAL FOR FUTURE USE. THE INSTALLER OR SELLER MUST LEAVE THE MANUAL TO THE CONSUMER.
-
Page 2: Table Of Contents
TABLE OF CONTENTS Warnings Assembly Gas Requirements & Connecting To A Gas Cylinder Securing A Gas Cylinder Minimum Clearance from Combustible Materials Gas Leak testing Lighting Instructions Safe Appliance Locations Maintenance & Servicing Storage Trouble Shooting Technical Data WARNINGS For outdoor use only ! ... - Page 3 Combustible materials are considered to be wood, compressed paper, plant fibers, plastic, plexiglas or other materials capable of being ignited and burned. Such materials shall be considered combustible even though flame proofed, fire retardant treated or plastered. Additional clearance may be required for glass, painted surfaces and other materials which may be damaged by radiant or convention heat.
- Page 4 PART LIST PART DESCRIPTION QUANTITY Reflector Panel Reflector Plate Head Assembly Deck Ring Top of Housing (preassembled) Door (preassembled) Door Lock (preassembled) Rear of Housing (preassembled) Gas Pipe Hose & Regulator Post Base (preassembled) Wheel Kit ALL HARDWARE CONTENTS (Include preassembled)
-
Page 5: Assembly
ASSEMBLY Instruction before assembly Required Tools: Philip Screwdriver / Adjustable Spanners / Wrenches Leak Detection Solution: one part detergent and three parts water Assemble all nuts and bolts loosely at first. Tighten all connections after completion of assembly. This eases your work and increases the stability of your appliance. - Page 6 3. Attach reflector panels (A) together using M6 x 8mm screws (FF), Φ6 washers (DD) and cap nuts (GG). Secure loosely with cap nuts (GG). Note: In order to achieve proper alignment of reflector sections, it may be necessary to loosen the preassembled bolts prior to assembly and retighten once complete.
- Page 7 6. Insert gas pipe with hose & regulator assembly (I/J) through top of housing (E) and Post (K), tighten gas pipe (I) to head assembly(C). Secure head assembly (C) to the post (K) using preassembled bolts M5 x 10 (HH), lock washer (JJ), and Φ5 washers (EE). Note: The control knob on head assembly (C) should be aligned with door (F).
-
Page 8: Safe Appliance Locations
SAFE APPLIANCE LOCATIONS This appliance shall only be used in an above ground open air situation with natural ventilation, without stagnant areas, where gas leakage and products of combustion are rapidly dispersed by wind or natural convection. Any enclosure in which the appliance is used shall comply with one of the following: An enclosure with walls on all sides, but at least one permanent opening at ground level and no overhead cover. - Page 10 OPERATING INSTRUCTIONS BEFORE FIRST USE AND AFTER EVERY GAS CYLINDER CHANGE, GAS DELIVERY SYSTEM MUST BE PURGED OF AIR BEFORE IGNITING! TO DO THIS, TURN THE CONTROL KNOB ANTI-CLOCKWISE TO THE PILOT SETTING. PRESS KNOB IN AND HOLD FOR 3 MINUTES BEFORE ATTEMPTING IGNITION. TO LIGHT THE PILOT ...
- Page 11 Soap bubbles will begin to form in the soapy solution if a leak is present. In case of a leak, turn off the gas supply. Tighten any leaking fittings, then turn the gas supply on and recheck. In case of any damage or gas leakage after several attempts, contact your local dealer for assistance.
- Page 12 IMPORTANT SAFETY RULES Ceiling/Overhang For use outdoors or in amply ventilated areas. An amply ventilated area must have a minimum of 25% of the 915mm Dia.815mm surface area open. The surface area is the sum of the walls surface. 915mm The use of this appliance in enclosed areas can be dangerous and is PROHIBITED.
-
Page 13: Storage
SERVICING Please consult your local dealer for servicing this appliance and replacement of its parts. The servicing of the appliance shall be carried out only by authorised personnel. Caution: do not use unauthorized parts or components for this appliance, only use original equipment replacement parts and components. -
Page 14: Technical Data
(see left photo) while pushing the control knob in the “PILOT” position. IN THE EVENT OF ANY PROBLEM, PLEASE ALWAYS CONSULT YOUR LOCAL DEALER. TECHNICAL DATA Model number: H1107G & H1207G Gas type: propane Nominal GC: 40.5MJ/h By-pass GC: 20.00MJ/h Test point pressure: 2.75kPa...
Need help?
Do you have a question about the H1107G and is the answer not in the manual?
Questions and answers