Summary of Contents for Cerruti BASIC HY Series
- Page 1 USER AND MAINTENANCE MANUAL HYDRAULIC SNOW BLOWER TWO STAGE BASIC HY series mod. L1400 SX Read this manual carefully before using the snow blower MA704403-GB...
- Page 2 CERRUTI S.R.L. VIA STATALE 27/H 14033 CASTELL’ALFERO AT Tel.(+39)0141/296957 – Fax (+39)0141-276915 Tax and VAT Number 01295490054 DECLARATION OF COMPLIANCE CERRUTI S.R.L declares under its own responsibility that the machine: SNOW BLOWER Model HY L1400 BASIC BS SERIAL n° ....Year ………..
-
Page 3: Table Of Contents
Index page Foreword …………………………………………………………….……1 Manufacturer details ..……………………………………………... 3 Product ID plate/CE marking . ……………………………………..3 Uses ..………….……………………………………………………. 4 Description and operation of the tool………………………..……... 4 Technical data ………………………………………………………… 6 General safety………………………………………………………... Safety devices and protections…………………………….……….. 10 Safety plates and symbols ..………………………………………… 11 Lifting/manoeuvring ……………………………………………………... - Page 4 The technical information contained in this manual is the property of CERRUTI and must be considered confidential. Reproduction, even partial, of the content and illustrations is prohibited by law.
-
Page 5: Manufacturer Details
Manufacturer Identification Details Manufacturer: CERRUTI S.R.L. Address: Via Statale, 27/H – 14033 Castell’Alfero (AT) Italy Telephone: +39 0141 296957 Fax: +39 0141 276915 E-mail: info@cerrutimacchineagricole.it Machine Identification Plate/CE Marking The machine model, the frame serial number and other identification and technical details are reported on the riveted metal identification plate located on the upper part of the body shell. -
Page 6: Uses
Uses - The BASIC HY snow turbine is a tool for application to an operating machine with the characteristics indicated on page 6, for the clearance of snow from roads, streets, pavements, squares, industrial areas, etc. It removes almost any kind of snow, as long as it is not too heavy (wet) or frozen. The speed of the tool depends on the type and depth of the snow. - Page 7 Description of the tool Warning! Observe the number of revs supplied by the manufacturer to avoid dysfunctions of the tool or excessive vibrations. 1- Body 10- Spacer barrier 2- Machine identity plate 11- Chute safety guard 3- Snow expulsion chute 12- Front guard 4- Lifting hook 13 –...
-
Page 8: Technical Data
Technical data 1400 Sx Working width 1400 mm - Working height 650 mm - Front worm diameter 395 mm - Rotor diameter 400 mm - Approx. mass with hitch plate 240 Kg - Hydraulic motor with gears - GR3-71cc Maximum working pressure 200 Bar –peak pressure 215 Bar. Number of hydraulic motor revs at full speed 900/1000 rpm - Expulsion chute with hydraulically controlled regulation of rotation and inclination. -
Page 9: General Safety
CERRUTI cannot be held responsible for accidents or damage caused by inadequately trained staff using the machine or staff misusing the machine as well as any inobservance, even partial, of the safety regulations and intervention procedures outlined in this manual. - Page 10 If any procedures or working techniques are used which are not explicitly advised by CERRUTI, you must ensure that there are no dangers to yourself and others and that these procedures are performed under your sole responsibility.
- Page 11 General Safety Regulations Regularly check the tightness of the screws and auger support nuts. Before attaching the quick release coupling to the vehicle distributor, ensure that the transport circuits and the turbine are not under pressure. Ensure that the quick release couplings are locked in their respective places. Before every use of the turbine, check that there are no cuts or abrasions on the hydraulic tubes and if there are, replace them with others provided by the manufacturer.
-
Page 12: Safety Devices And Protections
General Safety Regulations Warning! The operator must have suitable knowledge of the working area to avoid hitting or collecting objects which are dangerous or could injure people, or damage objects or the machine itself. If you do not have sufficient knowledge of the area, suspend the operation or proceed with maximum caution. -
Page 13: Safety Plates And Symbols
Safety Plates and Symbols Plates with safety symbols and/or messages of the various dangers that could arise during use are attached to the snow blower. Warning! Ensure that all safety messages are legible. Clean them using a sponge, water and soap. Do not use solvents, oil or petrol. -
Page 14: Lifting/Manoeuvring
Lifting/manoeuvring When lifting the tool, use the specific eyelet so that the tool is properly balanced. The weight of the tool is stated on machine data plate (A) Warning! The ropes must not touch the snow expulsion chute during the lifting phase. During the manoeuvring phases, the operator must ensure that the necessary safety conditions exist to guaranteed his safety and that of the other operators. - Page 15 Assembly/disassembly and connection - Lift the chassis (T) of the operating machine using the lift controls until the top part (H) of the plate engages. Ensure that it is engaged, then lift the tool slightly off the ground so that the hitching plates coincide. - Stop the operating machine and make sure that the tool is locked in place with the relative device (A) on the operating machine hitch.
-
Page 16: Instructions For Use
Assembly/disassembly and connection Connection chute control power supply A -B A1- B1 d T A1-B1 chute control power supply turbine power supply turbine delivery drain Warning! For correct use of the auxiliary line activation controls, follow the instructions in the operating machine instruction and maintenance booklet. Disassembly - Disconnect the hoses from the quick hitches and the electrical plug on the operating machine. -
Page 17: Maintenance
Use regulations Always check direction and angle of ejecting snow so as to avoid people or things. The rotation of the hydraulic vent is limited by a mechanical lock; be careful to not insist with the hydraulic control if the vent is not rotating. Rotation must always occur under maximum safety conditions and must never be aimed towards points or places which may be dangerous for people or things. - Page 18 Maintenance Before starting any maintenance operation, turn off the snow blower's engine. Attach a sign to the controls stating: MACHINE UNDER MAINTENANCE - DO NOT START ENGINE Before starting any maintenance operation: - Ensure that the engine is switched off. - Carefully read all the regulations contained in this manual.
-
Page 19: Worms And Transmission Unit
Maintenance Feeding screws and transfer case After finishing work it is important to remove all snow from the turbine with the included wooden stick, check if all screws securing the wear blade (D) and the transfer case mounting (B) are secured. = VTE M10x65 10.9 DIN931 + DE M10 DIN982 = VSP M8x25 DIN7991 +DE M8 DIN982... -
Page 20: Expulsion Chutes
Maintenance Expulsion chute At the end of every work cycle, grease point A on the thrust bearing with grade 2 mineral grease. Spread the grease on the endless screw inside the safety barrier (B). If the neck of the chute should become blocked, proceed as follows: - Turn the chute towards the side. -
Page 21: End Of Use/Garaging
Maintenance It is essential to equip the hydraulic system with a suitable filtration device, safety systems with reliable instruments and suitable systems to avoid turbulences in the fluid. Before starting up the motor at nominal power, we advise you follow the following tips = - check if rotation direction is correct. -
Page 22: Disposal
Scrapping and disposal The equipment’s scrapping operations must be performed by operators who are experts in the sector and in compliance with all standing regulations pertaining the issue: -do not release non-biodegradable products, oils and non-ferrous components (plastic, rubber, etc) into the environment. During scrapping, select all components based on their chemical and composition characteristics and carry out recycling. -
Page 23: Parts Subject To Wear And Tear
Parts subject to wear and tear List of parts normally subject to wear and tear 1- Lower blade code TN0020-04-05 2- Frontal half worms code TN2400-08-010 SX TN2400-08-020 DX 3- Rotor d.400 six code TN8001-01-006 4- Ribbed sleeve code TN9002-02-02... -
Page 24: Hydraulic System
Hydraulic system chute turbine... -
Page 25: Terms Of General Warranty
The faulty part must be returned to CERRUTI who, after inspecting it and verifying that the warranty is applicable, will repair or replace it, taking the necessary time to do so, without charging for either material or labour. - Page 28 CERRUTI srl Via Statale 27/H – 14033 Castell’Alfero (AT) Tel. +39 0141296957 Fax +39 0141276915 info@cerrutimacchineagricole.it www.cerrutimacchineagricole.it...