Summary of Contents for Puhui T-962 V2.0
- Page 1 INFRARED IC HEATER Mini Smart Reflow Oven User Manual Model: T-962 V2.0 SHANDONG PUHUI ELECTRIC TECHOLOGY CO.,LTD http://www.te168.com...
-
Page 2: Table Of Contents
http://www.te168.com CONTENTS PRODUCT DETAILS...................... PRODUCT FEATURES....................INSTRUCTIONS......................EXHAUST PIPE INSTALLATION ................MACHINE INTERFACE DESCRIPTION ..............EXECUTE TEMPERATURE CURVE ................SELF-SET CURVE (INDEPENDENT OPERATION) ........... SELF-SET CURVE (PC CONNETING) ............... THERMOSTATIC CONTORL ..................OPERATING DETAILS ................... SUGGESTIONS ....................... MAINTENANCE ...................... ATTENTIONS....................... -
Page 3: Product Details
http://www.te168.com Mini Smart Single Heating Zone Reflow Oven I. PRODUCT DETAILS 1. The product integrates the functions of reflow soldering, drying, insulation, shaping, rapid cooling, constant temperature timing to meet various soldering requirements such as SMD, BGA, etc., and capable of soldering single-sided and double-sided PCB in all packaging forms such as CHIP, SOP, PLCC, QFP, BGA, and more. -
Page 4: Instructions
http://www.te168.com INSTRUCTIONS III. EXHAUST PIPE INSTALLATION STEP 1 Loosen the screw on the fastening clamp of the exhaust pipe. (size of the exhaust pipe is Φ110mmx1500mm） STEP 2 Put the exhaust pipe on the product interface, tighten the fastening screws. STEP 3Place the exhaust pipe outdoor. -
Page 5: Machine Interface Description
http://www.te168.com MACHINE INTERFACE DESCRIPTION STEP 1 Please put machine on the flat tabletop with good ventilation and no combustible items nearby. Reserve space for drawer-pull & push. And leave at least 20mm space around the machine, for heat dissipation. Also ensure smooth ventilation at the bottom. STEP 2 Operation interface description STEP 3 Power on the machine, then LCD shows as below:... -
Page 6: Execute Temperature Curve
http://www.te168.com EXECUTE TEMPERATURE CURVE STPE 1 Press▲/▼Button to “Select Temp Curve”, then press OK/RETURN Button, the LCD will show as below: The initial curve is WAVE 1, press ▲ Button to switch to WAVE 2~WAVE 8. WAVE 1 for 85Sn/15Pb 70Sn/30Pb; WAVE 2 for 63Sn/37Pb 60Sn/40Pb;... -
Page 7: Self-Set Curve (Independent Operation)
http://www.te168.com SELF-SET CURVE (INDEPENDENT OPERATION) STEP 1 Select “Select Temp Curve”, then select WVAE 7 or WAVE 8. Press OK/RETURN Button enter the following editing interface: STEP 2 Press ▲/▼ Button to change the temperature value at current time. STEP 3 Press OK/RETURN Button to set the temperature value, and then the system will automatically jump to the next time point. - Page 8 http://www.te168.com SPECIAL NOTE: The system will automatically switch to the following interface, if there is no any operation for 2~3 seconds. Press OK/RETURN Button will save the curve and back to the main menu. STEP 4 When the temperature values at all time points are set, the new curve will be automatically saved and returned to the main menu.
-
Page 9: Self-Set Curve (Pc Conneting)
http://www.te168.com SELF-SET CURVE (PC CONNETING) STEP 1 Connect the machine with the computer using a serial cable. STEP 2 Open the Excel form “temperature data”. SPECIAL NOTE: The maximum temperature shall not exceed 280°C, and the temperature increase shall not exceed 3°C/s. STEP 3 Double-click the unmarked temperature cell to modify the temperature value. - Page 10 http://www.te168.com STEP 6 Open “SerialCom” software, it will show as below: SPECIAL NOTE: Baud rate/ Data bit/ Check bit/ Stop bit/ Receive/ Send parameters do not need to be set. STEP 7 Select the corresponding serial pot connected to the machine in the “COM port” drop-down list, then click the “Open port”...
-
Page 11: Thermostatic Contorl
http://www.te168.com THERMOSTATIC CONTORL STEP 1 Select the “Thermostat Control”, press the OK/RETURN Button enter into the operation interface. STEP 2 Press ▲/▼ Button to set the temperature value (Temperature Range: 40~280°C) STEP 3 After setting the temperature value, press OK/RETURN Button to adjust the time. STEP 4 Press ▲/▼... -
Page 12: Operating Details
http://www.te168.com OPERATING DETAILS A. Gently put the item to be processed on the flat surface in the drawer, close the drawer, then select the desired function and press OK/RETURN Button to execute. The LCD shows as below: B. The process will be done automatically under your supervision through the front window &... -
Page 13: Maintenance
http://www.te168.com MAINTENANCE A. The machine is equipped with an inner cavity cleaning function: after using it a few times, please run the heating curve without any components to allow the residual solvent and solder to evaporate. To ensure the inner cavity is clean and the performance of the whole machine is stable.
Need help?
Do you have a question about the T-962 V2.0 and is the answer not in the manual?
Questions and answers