Related Manuals for EDA ED-HMI3010-070C
Summary of Contents for EDA ED-HMI3010-070C
- Page 1 ED-HMI3010-070C 7-inch Industrial Panel PC Based on Raspberry Pi 5 User Manual EDA Technology Co., LTD January 2024...
- Page 2 IOT, industrial control, automation, green energy and artificial intelligence based on Raspberry Pi technology platform. You can contact us in the following ways: EDA Technology Co.,LTD Address: Building 29, No.1661 Jialuo Road, Jiading District, Shanghai Mail: sales@edatec.cn...
- Page 3 Copyright Statement ED-HMI3010-070C and its related intellectual property rights are owned by EDA Technology Co.,LTD. EDA Technology Co.,LTD owns the copyright of this document and reserves all rights. Without the written permission of EDA Technology Co.,LTD, no part of this document may be modified, distributed or copied in any way or form.
- Page 4 EDA Technology Co.,LTD does not guarantee that the information in this manual is up to date, correct, complete or of high quality. EDA Technology Co.,LTD also does not guarantee the further use of this information. If the material or non-...
-
Page 5: Reader Scope
ED-HMI3010-070C to help users understand the overall system parameters of the products. This document introduces the appearance, installation, startup ED-HMI3010-070C User Manual and configuration of ED-HMI3010-070C to help users use the product better. This document introduces the OS download, SD flashing and ED-HMI3010-070C Application Guide open/close device case of ED-HMI3010-070C to help users use the product better. - Page 6 Related Agreement Symbolic Convention Symbolic Instruction Prompt symbols, indicating important features or operations. Notice symbols, which may cause personal injury, system damage, or signal interruption/loss. Warning symbols, which may cause great harm to people.
-
Page 7: Safety Instructions
Safety Instructions This product should be used in an environment that meets the requirements of design specifications, otherwise it may cause failure, and functional abnormality or component damage caused by non-compliance with relevant regulations are not within the product quality assurance scope. ... -
Page 8: Table Of Contents
Content Foreword ..............................i Related Manuals ..........................i Reader Scope ............................i Related Agreement ..........................ii Symbolic Convention ........................ii Safety Instructions ............................. iii Product Description ......................... 1-1 Overview ........................... 1-2 Packing List ........................1-3 Appearance ........................1-4 1.3.1 Front Panel ........................ 1-4 1.3.2 Rear Panel ......................... -
Page 9: Product Description
1 Product Description 1 Product Description This chapter introduces the product overview, packing list, appearance, indicators and interfaces. Overview Packing List Appearance Indicator Interface ED-HMI3010-070C User Manual... -
Page 10: Overview
1 Product Description 1.1 Overview ED-HMI3010-070C is a 7-inch industrial Panel PC based on Raspberry Pi 5. According to different application scenarios and user needs, different specifications of RAM and SD card computer systems can be selected. RAM can choose 4GB and 8GB ... -
Page 11: Packing List
1 Product Description 1.2 Packing List 1x ED-HMI3010-070C Unit 4 x buckles (including 4xM4*8 screws and 4xM4*16 screws) ED-HMI3010-070C User Manual... -
Page 12: Appearance
1 x LCD display, 7-inch LCD touch screen, which supports up to 1024x600 and multi- point capacitive touchscreen. 1 x camera (optional), 8 Megapixel front camera. 1.3.2 Rear Panel This section introduces interfaces and definitions of rear panel. ED-HMI3010-070C User Manual... -
Page 13: Side Panel
1 Product Description Function Definition 4 x installation holes of buckle, which are used to fix the buckles to the device for installation. 1.3.3 Side Panel This section introduces interfaces and definitions of side panel. ED-HMI3010-070C User Manual... - Page 14 2 x HDMI ports, micro-HDMI connector, which can connect a display and supports 4K 60Hz. 1 x DC input, USB Type-C connector, which supports 5V 5A power input. Heat dissipation holes, which help improve cooling performance. ED-HMI3010-070C User Manual...
-
Page 15: Indicator
1 Product Description 1.4 Indicator This section introduces various statuses and meanings of indicators contained in ED-HMI3010-070C. Indicator Status Description The Ethernet connection is in the normal state. Yellow indicator Blink The Ethernet connection is abnormal. of Ethernet port The Ethernet connection is not set up. -
Page 16: Interface
1.5 Interface Introducing the definition and function of each interface in the product. 1.5.1 Power Supply The ED-HMI3010-070C includes one power input, and the silkscreen is “PWR IN”. The connector is USB Type-C, which supports 5V 5A power input. TIP: In order for Raspberry Pi 5 to achieve better performance, it is recommended to use a 5V 5A power adapter. -
Page 17: Hdmi
The connector is micro-HDMI, which can connect to HDMI displays and supports up to 4Kp60. 1.5.4 USB 2.0 ED-HMI3010-070C includes 2 USB 2.0 ports, and the silkscreen is " ". The connector is USB Type- A, which can connect to standard USB 2.0 peripherals and supports up to 480Mbps. -
Page 18: Installing Device
2 Installing Device 2 Installing Device This chapter introduces how to install the device. Installing Raspberry Pi 5 (optional) Embedded Installation ED-HMI3010-070C User Manual... -
Page 19: Installing Raspberry Pi 5 (Optional)
A cross screwdriver has been prepared. Steps: Insert the SD card into SD card slot of Raspberry Pi 5. Use a screwdriver to loosen 4 M3 screws on ED-HMI3010-070C case counterclockwise, and remove the case. ED-HMI3010-070C User Manual... - Page 20 2 Installing Device Use a screwdriver to loosen 4 M2.5 screws on heat sink counterclockwise, and remove the heat sink. ED-HMI3010-070C User Manual...
- Page 21 2 Installing Device Remove the film of thermal conductive silicone. ED-HMI3010-070C User Manual...
- Page 22 Raspberry Pi 5, and then place the heat sink on the Raspberry Pi 5 (make sure the four mounting holes of the heat sink are aligned with 4 mounting holes of the Raspberry Pi 5). ED-HMI3010-070C User Manual...
- Page 23 Here we only take installing Raspberry Pi 5 on an LCD screen with CAM interface as an example. Insert the mounting screws of the Raspberry Pi 5 into the mounting holes of the heat sink and tighten clockwise to fix the heat sink and Raspberry Pi 5 on the back of the LCD screen. ED-HMI3010-070C User Manual...
- Page 24 2 Installing Device Plug the power cord into the corresponding 40-Pin on the Raspberry Pi 5. Cover the case, insert 4 M3 screws, and tighten clockwise to fix the case to the back of the LCD screen. ED-HMI3010-070C User Manual...
-
Page 25: Embedded Installation
A cross screwdriver has been prepared. Steps: You need ensure the opening size of the cabinet according to the size of ED-HMI3010-070C, as shown in the figure below. Drill a hole on the cabinet according to the hole size of step1. - Page 26 Use 4 M4x8 screws to pass through the buckle and tighten it clockwise to fix the buckle to the device; then use 4 M4x16 screws to pass through the screw hole (threaded hole) of the buckle and tighten clockwise to the end through the buckles. ED-HMI3010-070C User Manual...
- Page 27 2 Installing Device ED-HMI3010-070C User Manual 2-10...
-
Page 28: Booting The Device
3 Booting The Device 3 Booting The Device This chapter introduces how to connect cables and boot the device. Connecting Cables Booting The System For The First Time ED-HMI3010-070C User Manual... -
Page 29: Connecting Cables
A network that can be used normally. Get the HDMI cable and network cable that can be used normally. Schematic diagram of connecting cables: Please refer to 1.5 Interface for the pin definition of each interface and the specific method of wiring. ED-HMI3010-070C User Manual... -
Page 30: Booting The System For The First Time
3.2 Booting The System For The First Time ED-HMI3010-070C has no power switch. After the power supply is connected, the system will start. The product is installed with the Desktop version system when it leaves the factory. After the device is started, it will directly enter the desktop. -
Page 31: Remote Login
4 Remote Login 4 Remote Login This chapter introduces how to log in the device remotely. Finding Device IP Connecting To The Device Desktop Through VNC ED-HMI3010-070C User Manual... -
Page 32: Finding Device Ip
When the device starts normally but the display is not connected, you can log in to the router to check the current device IP. Preparation: ED-HMI3010-070C has been connected to the network through the router. The IP and network password of the router in the network have been obtained, and the IP ED-HMI3010-070C User Manual... - Page 33 192.168.X.X. Steps: Open a browser, Enter the router IP of the network where ED-HMI3010-070C is located in the address bar: 192.168.x.x, and press Enter to enter the router login interface. According to the interface prompts, enter the network password and enter the router management interface.
-
Page 34: Connecting To The Device Desktop Through Vnc
The RealVNC Viewer tool has been installed on PC. ED-HMI3010-070C has been connected to the network through the router. IP address of ED-HMI3010-070C has been get. The VNC function in the ED-HMI3010-070C system has been turned on, as shown in the following figure. Steps: Open RealVNC Viewer and select "New connection…"... - Page 35 4 Remote Login After entering the IP address of ED-HMI3010-070C, click "OK". Enter the username and password in the Authentication prompt box that pops up. ED-HMI3010-070C User Manual...
- Page 36 4 Remote Login TIP: Default username is pi, Default password is raspberry. Select "OK" to log in and connect to the remote desktop. ED-HMI3010-070C User Manual...
Need help?
Do you have a question about the ED-HMI3010-070C and is the answer not in the manual?
Questions and answers