Advertisement
2. APPLICATION & SPECIFICATION
The SM47/C is designed to extract dust, saw dust and other fine debris from wood machining. It should not be used to extract metallic
debris, glass or water.
Specification:
Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .850cfm
Impeller diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .250mm
Collector hose diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125mm
Intake hose diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 x 100mm
Intake hose maximum length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2m
Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .230V, 50Hz, 1500W
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46kg
Noise level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .<87dBA
3. CONTENTS & ASSEMBLY
Unpack the extractor components and check that all are present and undamaged. In case of shortage or damage please contact the supplier.
Description:
• Collector Body with Motor
• Seal
• Base plate
• Hose
• Hose Clamp x 2
Note: Numbers in brackets are the item numbers on the parts diagram and in the parts list.
3.1.
Attach the four castors (1) to the underside of the base (3) using screws (23), washers (16) and nuts (19). Support base (3) on
battens, or similar, raising castors clear of floor to give stability for the following assembly tasks.
3.2.
With screws (6) and washers (4) attach motor base (5) to base (3).
3.3.
Attach motor (8) to motor base (5), so that collector body is positioned as shown in parts diagram, with screws (6) and washers (4).
3.4.
Attach fan housing (38) feet to base plate (3) with screws (6) and washers (4).
3.5.
Install outlet (30) to fan housing (38) using packing (29), screws (15), washers (16) and nuts (19).
3.6.
Attach collector supports (37) to base with screws (12) and washers (4) and to collector (33) with screws (6) and washers (4). Note
that upper bag support (13) is fitted to the collector (33) with the same screws as the middle support (37).
3.7.
Fit upper (filter) bag (35) over upper bag flange on collector (33) and secure by tightening built-in strap. Hook loop on end of bag
(55) over support arm (13). Fit second (collector) bag (36) to lower bag flange on collector.
Note: Bag clamps (34) are provided and may be used for additional bag security.
3.8.
Install hose (32) between outlet (30) and collector (33) and retain with hose clamps (31).
3.9.
Push-fit inlet (24) to inlet cover (25).
4. OPERATING INSTRUCTIONS
FWARNING! Before operating the extractor ensure that you read, understand and apply the safety instructions in Section
1. 4.1. Confirm that supply voltage matches the voltage shown on the motor data plate and that the motor switch (9) is ‘Off’.
4.2.
Connect extractor hose (39) to the inlet (24) and attach other end to extractor point on equipment. If only one extractor hose is to be used
ensure that the unused inlet is closed with the cap provided.
F
WARNING! DO NOT operate extractor without the hose(s) attached.
4.3.
Plug into mains supply and press motor switch ‘On’.
4.4.
Ensure that the lower bag is emptied of dust and chips on a regular basis and is not allowed to become full.
DUST & CHIP EXTRACTOR
Model SM47/C
73/23/EEC Low Voltage Directive
89/336/EEC EMC Directive
98/37/EC Machinery Directive
93/68/EEC CE Marking Directive
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this equipment.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
•
Filter/Collector Bag x 2
•
Support, Collector x 2
•
Screws, Nuts, Washers (1 bag)
•
Inlet
•
Bag Clamp x 2
Declaration of Conformity
in conformity with the following standards and directives.
Signed by Mark Sweetman
The construction file for this product is held by the Manufacturer and may be inspected, by a national authority, upon
request to Jack Sealey Ltd.
For Jack Sealey Ltd. Sole importer into the UK of Sealey Quality Machinery.
Sole UK Distributor,
Sealey Group,
Bury St. Edmunds, Suffolk.
01284 703534
• Collector
• Support Rod, Filter Bag
• Castors x 4
• Outlet
• Inlet Hose (2m)
We, the sole importer into the UK, declare that the product listed here is
E-mail:
27th March 2000
sales@sealey.co.uk
SM47/C - 1056 - (2) - 100800
Advertisement
