MCOHome AS-9 Quick Start Manual

9 ln 1 Multi-Sensor
AS-9
MCOHome A8-9 is a Z-Wave Plus enabled multiple environmental monitoring sensor, with 3.5 inch TFT clear
display that can monitor the air quality in-time. It is built in with Temperature, Humidity, PM2.5, CO2, VOC, PIR,
Illumination, Noise, Smoke sensor. Device can be added into any Z-Wave network, and is compatible with any other
Z-Wave certified devices.
Temperature: 0~50 C
Humidity: 0%RH~99%RH
PM2.5: 0~500ug/m3
C02: 0~5000ppm
VOC: 0-64000ppb
PIR: 0
or
1 Detection angle up to 120°
Illumination: 0--40000 Lux
Noise: 30dB~ IO0dB
Smoke: 0or 1
Power Supply: DC12V, 50/60Hz
Self-Dissipation:<3W
•
Specification
Work Environment:-20--+60
·c
<99%RH (Non-condensation)
Dimension: 110* 110*32mm
Hole Pitch: 60mm or 82mm
A
A
A
A
A
Read the instructions before starting up the unit!
This product is nota toy. Keep out ofreach of children and animals!
Do not expose the device to moisture, water or other liquids. Do not place liquids near or on the device!
Do not attempt
to
disassemble, repair or modify the device yourselfl
This product is for indoor use only. Do not use outdoors!
A
CAUTIONS!
Flush-mount only into a UL/ETL/CE certified plastic junction box. The minimum size should be
65*65*45mm, minimum Volume is 190cm3. Use Copper Conductors Only.
A
CAUTIONS!
Risk of Electric Shock - More than one disconnect switch may be required to de-energize the
equipment before servicing.
Installation& Wiring
To protect yourself and others from danger and to protect the device from damage, please read the safety
information before using it.
A
Important!
Operation
Power On/Off
Wire the adaptor and the device is powered on. It will display all detected information by the sensors.
Display Interface
Hold Key Fl can switch among the following 4 display interfaces:
1. Data detecting: display all sensors' data
2. Network: Z-Wave Add/Remove
3. Parameter setting: e.g. data calibration, temp. format, restore default parameters etc
4. Local time setting
Z-Wave Operation
Note: A Security Enabled Z-Wave Controller must be used in order to Jully utilize the producl
• Add &Remove Z-Wave network
►
Activate Add/Remove mode in the gateway. When device is powered on, hold Fl to choose interface for Add or
Remove Z-Wave network.
Z-Wave Frequency: Operating frequency range, defined by the regulatory bodies {for Z-wave in Europe:
868.0 - 868.6 MHz, 869.7 - 870.0 MHz)
Maximum Transmitting Power: +3dBm
Housing: Tempered glass+ PC Alloy
Installation: Wall-mounted (Vertical)
Declaration of Conformity
Hereby, MCOHome declares that the device is in compliance with the essential requirements
and other relevant provisions of Directive 2014/53/EU .
WEEE Directive Compliance
1t
The device marked with this symbol should not be disposed ofwith household waste.lt is the
user
1
s responsibility to deliver the used appliance to a designated recycling point.
-
Z -Wave Compliance
~o:j;N
MCOHome sensor is a fully compatible Z-Wave Plus device.
Important Safety Instruction
• A qualified electrician with the understanding of wiring diagrams and knowledge of electrical safety
should complete installation following the instructions.
• Before installation, please confirm the real voltage complying with the device's specification.
Cut off an.y power supply to secure the safety of people and device.
• During installation, protect the device from any physical damage by dropping or bumping. If happens,
please contact the supplier for maintenance.
• Keep the device away from acid-base and other corrosive solids, liquids, gases, to avoid damage.
• Avoid overexertion during operation, to protect device from mechanical damage.
• Read all instructions and documentation and save for future reference.
Location:
Device is suggested to be installed indoor, a place with around 1.5m height above the floor. It should be away from
direct sunlight, an.y cover, or any heat source, to avoid false signal for temperature control.
Notice!
1. Device must be wall-mounted vertically. Do not lay it fiat or upside down while working.
2. Do not mounted it in a wind gap, or cover its bottom, which may affect the detected data.
Step
1:Remove the steel frame from the backside of the device, and then fix it onto the installation box with 2
screws.
Step 2: Wire the adaptor.
Step
3:Put the device back onto the steel frame, it will attach with the frame finnly by built-in magnets.
Step
4:Check the installation and power, the device is ready for work.
4
►
Click F2 five times until
C
turns blue.
►
Hold F2 and the device enter into learning mode, then turns blue and the device is added into Z-Wave network.
►
Follow the same step to remove the device from network.
Association Group
Device supports 1 association group:
AG
Max Command
Trigger Situation
Identifier Node ID Class
Detected value will be reported according to:
1, PM2.5 The value difference between current value and previous
reported value > the setting value of parameter number 1, set value;t0;
2, CO2 The value difference between current value and previous
reported value> the setting value ofparameter number 2, set valuet<);
3, Temperature The value difference between current value and previous
reported value > the setting value of parameter number 3, set value;t0;
4, Humidity The value difference between current value and previous
reported value > the setting value of parameter number 4, set value;t0;
COMMAND 5, VOC The value difference between current value and previous
CLASS
reported value > the setting value of parameter number 5, set value;t0;
-
SENSOR_
6, Illumination The value difference between current
0x0I 1
MULTIL
value and previous reported value > the setting value of parameter
EVEL_V5,
number 6, set value:;t:0;
SENSOR 7, Noise The value difference between current value and previous
MULTILE
reported value > the setting value of parameter number 7, set value;t0;
VEL
8, PIR The current state is different from previous reported state, set
REPORT_
value:;t:0;
V5
9, Smoke The current state is different from previous reported state, set
value:;t:0;
10, Smoke Interval Report Timer set value: 10 and set value:;t:0;
11, PIR Interval Report Timer set value: 11 and set value:;t{);
12, PM2.5 Interval Report Timer set value: 12 and set value:;t:0;
13, CO2 Interval Report Timer set value: 13 and set value:;t:0;
14, Temperature lnterval Report Timer set value: 14 and set valuet<);
15, Humidity Interval Report Timer set value: 15 and set value:;t{);
16, VOC lnterval Report Timer set value: 16 and set value,'();
17, Illumination Interval Report Timer set value: 17 and set valuet<);
18, Noise lnterval Report Timer set value: 18 and set value:;t:0;