Page 1
PRO200WW1836 Instruction Manual 200 Watt Warm White LED Zoom Profile Spot CAUTION - ATTENTION - VORSICHT RISK OF ELECTRIC SHOCK- DO NOT OPEN RISQUE D’ELECTROCUTION- NE PAS OUVRIR STROMSCHLAGGEFAHR- NICHT OFFNEN In Compliance with the following directives: RoHS Directive (2002/95/EU) and WEEE Directive (2002/96/EU) If this product is no longer functional or reaches the end of its usable life, please take it to an approved recycling plant.
Page 2
For your safety and to ensure you make full use of the PRO200WW1836 features, please make sure you read this manual in full. Before Use •...
Page 3
• The operator must make sure the light fitting has been installed correctly to all the necessary guidelines before each use. • The installation should be inspected every 6 months. PRO200WW1836 Manual.indd 3 PRO200WW1836 Manual.indd 3 21/09/2023 12:05:34 21/09/2023 12:05:34...
3. When the units’ temperature is greater than the protecting circuit, 30% of the power is reduced to the LED slowly. Normal output will resume once the internal temperature has lowered. PRO200WW1836 Manual.indd 4 PRO200WW1836 Manual.indd 4 21/09/2023 12:05:34 21/09/2023 12:05:34...
Bracket Knob Fasten the light into the desired position. 10 Display & Menu Buttons Used to adjust the units settings. 11 Locking Clip Used to keep the colour frame in place. PRO200WW1836 Manual.indd 5 PRO200WW1836 Manual.indd 5 21/09/2023 12:05:35 21/09/2023 12:05:35...
Page 6
Used to go to the next menu or decrease parameter value. 15 Enter Button Used to select a menu option or confirm a setting. 16 Display Shows the various menus and selected functions. PRO200WW1836 Manual.indd 6 PRO200WW1836 Manual.indd 6 21/09/2023 12:05:35 21/09/2023 12:05:35...
0-255 Brightness micro-adjustment 3CH Channel Table Channel Value Rate Control Function Dimmer 0-255 Dimmer, brightness from 0-100% DimmerFine 0-255 Brightness micro-adjustment Strobe 0-255 0-255 Strobe frequency (from slow to fast) PRO200WW1836 Manual.indd 7 PRO200WW1836 Manual.indd 7 21/09/2023 12:05:35 21/09/2023 12:05:35...
Page 8
A DMX terminator is simply a male XLR plug with 120 Ohms, ¼ watt resistor, soldered across pins 2 and 3. You can also buy these pre-made. PRO200WW1836 Manual.indd 8 PRO200WW1836 Manual.indd 8 21/09/2023 12:05:35...
Page 9
When setting your DMX address, you must ensure fixtures don’t overlap from one to the next. You can set two fixtures to the same address, and as long as they are the same fixture (i.e. same channel layout) then they will do the same as each other. PRO200WW1836 Manual.indd 9 PRO200WW1836 Manual.indd 9 21/09/2023 12:05:35...
Page 10
Thank you for taking the time to read this information. For further information, please contact sales@terralec.com or visit www.terralec.co.uk PRO200WW1836 Manual.indd 10 PRO200WW1836 Manual.indd 10 21/09/2023 12:05:35 21/09/2023 12:05:35...