Table of Contents
Advertisement
Quick Links
Temperature Relays and MINIKA®
Operating Manual STW164IP
For more information and help about this product please scan the
choose the following link:
Operating manual, Quick guide, Datasheet, Connection diagram, CAD Data
Firmwareupdates, FAQ, Videos about installation and settings, Certificates
- extraction systems
Control of up to 32 sliders via bus line in connection with bus modules STW168M and STW161M
STW164IP
12660-0710-00
Mains Monitoring
Digital Panelmeters MINIPAN®
STW164IP
Switching Relays and Controls
Page 1 / 30
ZIEHL industrie – elektronik GmbH + Co KG
Daimlerstr.13, 74523 Schwäbisch Hall, Germany
+ 49 791 504-0,
info@ziehl.de,
Measuring Transducers
Grid- and Plant Protection
updated: 2023-12-05 / dr
from Firmware: 0-00
QR-Code
or
www.ziehl.deAA
www.ziehl.de
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ZIEHL STW164IP
Summary of Contents for ZIEHL STW164IP
- Page 1 ZIEHL industrie – elektronik GmbH + Co KG Daimlerstr.13, 74523 Schwäbisch Hall, Germany + 49 791 504-0, info@ziehl.de, www.ziehl.de Temperature Relays and MINIKA® Mains Monitoring Digital Panelmeters MINIPAN® Switching Relays and Controls Measuring Transducers Grid- and Plant Protection updated: 2023-12-05 / dr...
-
Page 2: Table Of Contents
Menu pages .......................... 17 10.6 Parameters ..........................18 10.6.1 Machines ..........................18 10.6.2 Extraction ..........................19 10.6.3 Cleaning ..........................20 10.6.4 Discharge ..........................20 10.6.5 Relays ..........................21 10.6.6 Analog Output ........................21 STW164IP 12660-0710-00 Page 2 / 30 www.ziehl.de... -
Page 3: General Notes
Deviations from the following requirements may therefore lead both to the loss of the statutory material defect liability rights and to the liability of the buyer for the product that has become unsafe due to the deviation from the specifications. STW164IP 12660-0710-00 Page 3 / 30... -
Page 4: Display And Controls
Volume flow Line Priority 1...16 End position Y4 Default My data (addresses of STW168M or STW161M) value On/off I-limit value 3.0A Delay on Overrun time Volume flow Line Priority 17^32 End position Y4 STW164IP 12660-0710-00 Page 4 / 30 www.ziehl.de... - Page 5 Interval break time Continuous vibration time 00:50 [mm:ss] Continuous vibration time Cleaning Input Y2 Input Y2 Discharge Starts with Cleaning when Configuration→Discharge Start condition cleaning is pending Overrun time 00:00 [mm:ss] Overrun time STW164IP 12660-0710-00 Page 5 / 30 www.ziehl.de...
-
Page 6: Application And Brief Description
It switches on the central extraction and opens the sliders on the channels to the individual machines. 8-fold slider modules are used to control the sliders. These can be mounted next to the STW164IP or distributed in the system. The latter reduces the wiring effort. -
Page 7: Overview Of Functions
Interval vibration time: 1...30s • Interval break time: 1...120s • Continuous vibration time: 0...1200s • Optional pulse vibration 0.1...10s (rectangle) • Optional cleaning request (while the extraction is running) for cleaning with compressed air STW164IP 12660-0710-00 Page 7 / 30 www.ziehl.de... -
Page 8: Connection Diagram
Convenient display of operating states and programming on the computer via a web browser 6 Connection Diagram Inverter Extraction Cleaning Adjustable options on Relays K3 and K4: - Control of discharge, - Message from Faults End position errors Volume flow exceeded ... STW168M ... STW161M STW164IP 12660-0710-00 Page 8 / 30 www.ziehl.de... -
Page 9: Connection Of Additional Power Supplies
Both DIP switches "RS485 terminate" to on If the STW164IP is not located at the beginning or end of the BUS line, the terminating resistors must be switched on at the corresponding STW168M or STW161M (beginning and end of the BUS line). -
Page 10: Ethernet
➢ After delay time for extraction [Extraction / Overrun time] ➢ Switches off the extraction system ➢ After delay time (machine, last overrun) [Machine / last overrun] ➢ The slider / flap of the extraction channel closes STW164IP 12660-0710-00 Page 10 / 30 www.ziehl.de... -
Page 11: Volume Flow
3. Vibration - 0.1^10.0 s (pulse) [Cleaning / Vibration] The relay K2 switches on/off during the interval vibration time and during the continuous vibration time in the set time interval. STW164IP 12660-0710-00 Page 11 / 30 www.ziehl.de... -
Page 12: Addition Time
The volume flow takes into account the open sliders (total volume flow of all extraction channels) • The function "Extraction/further opening = no" is not active (open all) • When extraction off: Extraction starts without delay STW164IP 12660-0710-00 Page 12 / 30 www.ziehl.de... -
Page 13: Input Y2
(OUT O+, O-), it must have reinforced insulation / safe isolation from the load/mains side. Attention! When using current transformers STWA1 or STWA1H for current measurement, the following must be observed: Only one current-carrying conductor may be passed through the current transformer. STW164IP 12660-0710-00 Page 13 / 30 www.ziehl.de... -
Page 14: Assembly
(German/English) and select. 10.3 Device on the network If the STW164IP is connected to a network via an Ethernet, the measured value display and programming can be performed via a web browser on the computer. Basic knowledge of network engineering is required for configuration. -
Page 15: Device Operation
2 seconds to call up the menu error BUS Menu: Scroll down Navigate between display pages: Call up menu: Press and hold for 2 seconds 10.5 Displays on the device 10.5.1 Display Pages STW164IP 12660-0710-00 Page 15 / 30 www.ziehl.de... - Page 16 U Out: Voltage at output OUT (terminals O+/O-) • Code lock: Code lock against unauthorized adjustment on the device = off / • IP address: IP address of the device in the Ethernet network STW164IP 12660-0710-00 Page 16 / 30 www.ziehl.de...
-
Page 17: Display Page, Filter Cleaning
Exit parameter menu: Press right → (several times) until the green tick is activated. Using the ↓ / ↑ keys, select the (discard change) or the tick (save changes) and leave by pressing → STW164IP 12660-0710-00 Page 17 / 30 www.ziehl.de... -
Page 18: Parameters
Start with swipe signal, sliders remain 00:00:00... 01:00:00 open for the set time hh:mm:ss Time offset when multiple sliders open at the same time Offset open Global Settings: Slider offset 00.00..02.50 ss,ss open 0.0..2.5s STW164IP 12660-0710-00 Page 18 / 30 www.ziehl.de... -
Page 19: Extraction
Min. vol line Min. volume flow line Minimum volume flow in the respective extraction line. In order to achieve this, additional sliders/flaps in the line may be opened 1.100% 1.100% STW164IP 12660-0710-00 Page 19 / 30 www.ziehl.de... -
Page 20: Cleaning
Overrun time Overrun time of the discharge starts as soon as the Overrun time 0...1200s condition for the discharge is no longer met. 00:00..20:00 mm:ss STW164IP 12660-0710-00 Page 20 / 30 www.ziehl.de... -
Page 21: Relays
/ Relay K3 / Relay off / Rel K4 / Rel K3 - Error from RS485 BUS (device not reachable) - Error Us 24V from STW164IP - Error in internal memory - Error in parameter - Error in parameter for priority of slider... -
Page 22: Network
-> code lock on/off -> enter old code (factory setting 504) -> enter new code (only if code lock on) Set factory reset Reset device to factory default Factory setting yes / STW164IP 12660-0710-00 Page 22 / 30 www.ziehl.de... -
Page 23: Simulation
On the device, In the web browser, Menu / Info Register Counter Operating hours Counter STW164IP and Operating hours of devices controlled by the STW164IP. Counter The values can be reset via the web interface STW161M / STW168M Slide Counter Counter Number of slider openings. -
Page 24: Web Interface
Save firmware (compare firmware versions with information in the table to see if newer version is available) o Start update (selection of downloaded firmware, upload to STW164IP) o Update (the STW161M/STW168M with the selected address will receive the firmware update) -
Page 25: Register - Network
Error status Description Error Log... machine 1...31: bit-0 (valence = 1): Module is switched on in configuration of STW164IP bit-1 (valence = 2): Communication to STW161M / STW168M available bit-2 (valence = 4): Relay on STW161M / STW168M has energized... -
Page 26: Register - Counter
(valence = 64): Error in parameter for priority (STW161M/ STW168M - priority the same several times) bit-7 (valence = 128): internal device error bit-8 (value = 256):Error on supply voltage of STW164IP (voltage too high / too low) bit-9 (valence = 512): Error on display of STW164IP No errors are logged during a simulation on the device / via the website. -
Page 27: Toubleshooting And Measures
Display / website reports: >><< Cause The supply voltage on the STW164IP is too high or too low Check supply voltage on STW164IP. Remedy If the voltage is too low, this can be remedied with an additional power supply unit in the BUS line (see connection diagram) ■... -
Page 28: Technical Data
Inputs I0...I31 (I0...I15 also possible directly on STW164IP) Current transformers - STWA1(H) (terminals I- and I0.I15) - Potential-free contact (terminals Y+ and I0.I15) - Ziehl current sensor S1 (S1 output PNP at I0.I15, Us of S1 at Y+ and I-) approx. 15kQ AC internal resistance max. - Page 29 (twisted pair) Length max. 1000m (RS485 BUS) When selecting and dimensioning the cable, it must be ensured that sufficient voltage is available on each BUS participant (STW164IP, STW161M/STW168M with slider/flaps). Power consumption of the BUS devices for the calculation: • STW164IP approx.
-
Page 30: Design V8
16 Disposal Disposal should be carried out properly and in an environmentally friendly manner in accordance with legal provisions. ZIEHL is registered with the EAR Foundation under WEEE no .: DE 49 698 543. STW164IP 12660-0710-00 Page 30 / 30...
Need help?
Do you have a question about the STW164IP and is the answer not in the manual?
Questions and answers