Tri-light/lane light with camera assembly (37 pages)
Summary of Contents for NCR 7360-K071
Page 1
Kit Instructions Standard Tri–Light/Lane Light Assembly and Lane Light Label (Self Checkout) 7360-K071 Issue A...
Page 2
NCR, therefore, reserves the right to change specifications without prior notice. All features, functions, and operations described herein may not be marketed by NCR in all parts of the world. In some instances, photographs are of equipment prototypes. Software screen images are representative, and in some cases, may not match a customer’s installed software exactly.
Standard Tri–Light/Lane Light Assembly with Lane Light Label (Self Checkout) This publication provides procedures for installing a Standard Tri–Light/Lane Light Assembly and Lane Light Label (Self Checkout) to an NCR FastLane SelfServ Checkout (7360) unit. Kit Contents Part Number Description 497-0527614 7360-K071 R6 Tri-Light, Standard Pole And Label "Self...
Page 5
Standard Tri–Light/Lane Light Assembly with Lane Light Label (Self Checkout) Part Number Description 497-0525777 Assembly - Tri-Light/Lane Light Housing, Normal 006-8624498 Screw - M4 x 0.7 x 8 mm, Flat Head, Stainless 006-8623599 Plug – Locking, Flush, 9.5 mm Hole, Black (2 pcs) 497-0523835 Cable - Trilight And Lane Light Extender 009-0006598...
Standard Tri–Light/Lane Light Assembly with Lane Light Label (Self Checkout) Installation Procedures Installing the R6 Standard Tri–Light/Lane Light Assembly and Lane Light (Self Checkout) involves the following procedures: • Removing Tri–Light/Lane Light Assembly on the next page. • Removing Tri–Light/Lane Light Pole on page 8.
Page 7
To remove the Tri–Light/Lane Light assembly (with or without Camera), follow these steps: 1. Turn off the NCR SelfServ Checkout software and hardware systems. For more information, refer to "General Operational Procedures" section of NCR SelfServ™ Checkout (7360) Hardware Service Guide (B005–0000–2378).
Page 8
Standard Tri–Light/Lane Light Assembly with Lane Light Label (Self Checkout) Tri–Light/Lane Light with Camera Assembly...
Page 9
Standard Tri–Light/Lane Light Assembly with Lane Light Label (Self Checkout) 3. Lift the Tri–Light/Lane Light Assembly and then disconnect the cables. Tri–Light/Lane Light Assembly...
Page 10
Standard Tri–Light/Lane Light Assembly with Lane Light Label (Self Checkout) Tri–Light/Lane Light with Camera Assembly Note: The assembly has cable ties that provide strain relief for the connectors. Cut these cable ties before disconnecting the connectors.
Page 11
Standard Tri–Light/Lane Light Assembly with Lane Light Label (Self Checkout) Removing Tri–Light/Lane Light Pole To remove the Tri–Light/Lane Light Pole, follow these steps: 1. Insert key in lock on the back of tower and then turn counterclockwise to unlock the terminal.
Page 12
Standard Tri–Light/Lane Light Assembly with Lane Light Label (Self Checkout) 3. Remove the Scanner/Scale to access the screws that secure the Tri–Light/Lane Light Pole. 4. Remove the two (2) screws securing the Tri–Light/Lane Light Pole to the tower. 5. Remove the cables out of the Tri–Light/Lane Light Pole. 6.
Page 13
Standard Tri–Light/Lane Light Assembly with Lane Light Label (Self Checkout) Installing Lane Light Label To install the label on each side of the Lane Light, follow these steps: 1. Remove the Tri–Light/Lane Light assembly, if necessary. 2. Wipe any dust or dirt on the surface of both sides of the Lane Light. 3.
Page 14
Standard Tri–Light/Lane Light Assembly with Lane Light Label (Self Checkout) 5. Hold half of the label in place while peeling off the protective film from the other half of the label and then attach the label on the Lane Light, as shown in the image below.
Page 15
Standard Tri–Light/Lane Light Assembly with Lane Light Label (Self Checkout) Installing Tri–Light/Lane Light Pole To install the Tri–Light/Lane Light pole, follow these steps: 1. Remove the existing Tri–Light/Lane Light Pole, if necessary. For more information, refer to Removing Tri–Light/Lane Light Pole on page 8.
Page 16
Standard Tri–Light/Lane Light Assembly with Lane Light Label (Self Checkout) 4. Insert the Tri–Light/Lane Light cable through the opening in the side of Tri– Light/Lane Light pole and route it out the top of the pole. Note: For the Tri–Light/Lane Light assembly without a camera, only the Tri– Light/Lane Light cable extender exist in the assembly.
Page 17
Standard Tri–Light/Lane Light Assembly with Lane Light Label (Self Checkout) 5. Route the cables coming out of the unit so they align with the grooves and carefully insert the pole into the tower. 6. Secure the pole to the tower with two (2) screws.
Page 18
Standard Tri–Light/Lane Light Assembly with Lane Light Label (Self Checkout) 7. Insert the excess cables into the opening on the Tri–Light/Lane Light pole so that the cables will not interfere with any outer items.
Page 19
Standard Tri–Light/Lane Light Assembly with Lane Light Label (Self Checkout) Installing the Tri–Light/Lane Light Assembly Note: To install a Tri–Light/Lane Light with Camera Assembly, refer to 7360-K066 Tri- Light with Camera Assembly Kit Instructions for more information. To install the Tri–Light/Lane Light assembly, follow these steps: 1.
Page 20
Standard Tri–Light/Lane Light Assembly with Lane Light Label (Self Checkout) 4. Insert the Tri–Light/Lane Light assembly into the Tri–Light/Lane Light pole. Ensure that the pole holes are aligned.
Page 21
Standard Tri–Light/Lane Light Assembly with Lane Light Label (Self Checkout) 5. Secure the Tri–Light/Lane Light assembly to the pole with a screw. 6. Run the ADD utility to ensure device is updated with the latest firmware.