Download Print this page

Tyco Electronics v Series Product Manual

Multipurpose power line rfi filter for emission control and high-noise industrial environments

Advertisement

Quick Links

V and W Series
UL Recognized
CSA Certified
VDE Approved
V and W Series
The V series and W series filters will better protect
equipment from malfunctions due to conducted
interference coming into the equipment from the line,
especially line-to-line noise and transients. They will also
provide needed noise suppression to allow most
equipment to meet FCC specifications for conducted
emissions.
V Series – offers an N = 3 ("T") line-to-ground impedance
to common mode and an N = 5 ("Dbl. Pi") impedance for
line-to-line differential mode interference. The filters are
designed for susceptibility use when equipment
impedance at RF frequencies is low.
W Series – provides an N = 4 ("Dbl. L") line-to-ground
impedance for common mode and an N = 5 ("Dbl. Pi")
impedance for line-to-line differential mode interference.
The filters are designed for use when equipment
impedance at RF frequencies is high. The two-stage
construction provides excellent suppression at high
frequency.
V series and W series filters are also effective to control
emissions in equipment using SCR and T
compliance with FCC Part 15, Subpart J, and EN55022,
Level A, down to 150kHz.
Electrical Schematics
V Series
LINE
W Series 3A, 6A, 10A
LINE
W Series 20A
LINE
Resistor location for reference only.
98
Catalog 1654001
Dimensions are in inches and
Revised 05-07
millimeters unless otherwise
specified. Values in italics
are metric equivalents.
CORCOM Product Guide
Multipurpose Power Line RFI Filter for Emission Control
and High-Noise Industrial Environments
2
L circuits, for
LOAD
LOAD
LOAD
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
VV1/VW1
3A, 6A, 10A
Specifications
Maximum leakage current,each line-to-ground
@ 120 VAC 60 Hz:
@ 250 VAC 50 Hz:
Hipot rating (one minute):
line-to-ground
line-to-line
Operating frequency:
Rated voltage (max.):
Rated current:
3VV/3VW
6VV/6VW
10VV/10VW
20VV/20VW
Minimum insertion loss in dB:
Line-to-ground in 50 ohm circuit
Current
Frequency–MHz
Rating
.15
.5
1
V Series
3A
15
27
38
6A
15
27
28
10A
15
27
38
20A
15
30
41
W Series
3A
13
25
20
6A
18
30
34
10A
18
30
34
20A
18
30
34
Line-to-line in 50 ohm circuit
Current
Frequency–MHz
Rating
.15
.3
.5
V Series
3A
25
25
65
6A
40
54
65
10A
25
25
65
20A
25
25
65
W Series
3A
25
40
65
6A
30
54
65
10A
25
25
65
20A
25
25
65
USA Cust. Svc.: 1-800-468-2023
CORCOM Prods: 1-847-680-7400
Germany:
49-89-6089-0
VV6/VW6
20A
0.5 mA
.82 mA
2250 VDC
1450 VDC
50/60 Hz
250 VAC
3A
6A
10A
20A
2
5
10
20
30
47
55
55
50
48
47
55
55
50
48
47
55
55
50
48
49
60
46
36
30
45
65
65
65
63
40
65
65
57
47
40
65
65
57
47
40
65
65
57
47
1
2
5
10
20
30
65
63
60
52
50
50
65
65
65
60
57
55
65
63
60
52
50
50
65
63
60
52
50
50
65
65
62
55
35
35
65
65
60
55
38
38
65
65
65
50
45
45
65
65
65
50
45
45
www.corcom.com
www.tycoelectronics.com

Advertisement

loading
Need help?

Need help?

Do you have a question about the v Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Tyco Electronics v Series

  • Page 1 1450 VDC emissions. Operating frequency: 50/60 Hz V Series – offers an N = 3 (“T”) line-to-ground impedance Rated voltage (max.): to common mode and an N = 5 (“Dbl. Pi”) impedance for 250 VAC line-to-line differential mode interference. The filters are...
  • Page 2 5.65 3.12 2.29 20VW7 — — 2.00 143.51 79.25 58.17 50.8 Part Numbers V Series W Series 03VV1 03VW1 Typical dimensions: 06VV1 06VW1 Terminals: .250 [6.35] (5) Holes: .07 [1.8] Dia.(4) 10VV1 Slot: .07 x .16 [1.8 x 4.1] 10VW1...

This manual is also suitable for:

W seriesVv1Vw1Vw6Vv6